HOMEDEPOT G19716-BK, WH Selectable CCT LED Wall Lantern User Guide

HOMEDEPOT G19716-BK, WH Selectable CCT LED Wall Lantern

Safety Information

Read and understand this entire manual before you attempt to assemble, install, or operate this product.

WARNING:
turning off the circuit breaker or by removing the fuse at the fuse box.

Consult a qualified electrician if you have any electrical questions or need to replace the driver.
If you have any non-electrical questions about this fixture, please contact our Customer Service Team at 1-877-527-0313 or visit www.HOMEDEPOT.com. Keep your receipt and these instructions for proof of purchase.

FCC NOTICE

NOTE: This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1.  This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

• Reorient or relocate the receiving antenna.
• Increase the separation between the device and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is located.
• Consult the dealer or an experienced radio/TV technician for help.

Warranty

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of three (3) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the not be liable for any consequential or incidental loss or damage, including but not limited to any labor or expense costs involved in the replacement or repair of said product.
Contact the Customer Service Team at 1-877-527-0313 or visit www.HOMEDEPOT.com.

Pre-Installation

PLANNING INSTALLATION

Before beginning installation, make sure all parts are included using the Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate the product.
To avoid damaging this product, place it on a soft, non-abrasive surface, such as carpet or cardboard.

TOOLS REQUIRED (NOT INCLUDED)

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

PACKAGE CONTENTS

Installation

Installing the mounting bracket

• Thread the fixture mounting screws (DD) into the provided holes of the mounting bracket (EE).
• Pull the supply wires out from the outlet box (1) and mount the mounting bracket (EE) using the bracket mounting Screws (CC).
• Place the fixture pan (C) over the outlet box (1) and onto the fixture mounting screws (DD).
• Adjust the fixture mounting screws (DD) until they protrude Out from the fixture pan (C) 1/4 in.
• Remove the fixture pan (C) and secure the position of the fixture mounting screws (DD) by threading against the mounting bracket (EE).

Connecting the wires

• Connect the black supply wire to the black fixture wire using a wire nut (BB).
• Connect the white supply wire to the white fixture wire using a wire nut (BB).
• Connect the ground wire from the outlet box to the ground screw (D) of the mounting bracket (EE).
• Wrap all wire connections with electrical tape for more secure connections.
• Carefully tuck the wires and wire nuts (BB) into the outlet box.

NOTE: If you have electrical questions, consult your local electrical code for approved grounding methods.

Installing the fixture

• Place the fixture pan (C) onto the fixture mounting screws (DD) and secure it into place by using the lock nuts (AA).
• Place the cage (A) over the glass shade (B) and place both parts over the fixture pan (C). Secure the cage (A) to the fixture pan (C) by using the cage screws (E).
• Turn the power on at the circuit breaker or fuse box.
• Turn the light switch on to activate the fixture.

Color temperature adjustment

• The initial time the light is energized, the color temperature is 3000K.
• Turn off the switch and on again within 3 seconds, the color temperature changes to 5000K.
• Turn off the switch and on again within 3 seconds, the color temperature changes to 4000K.
• Repeat this process for desired color temperature.
  (The switch is installed on wall, not included in product.)

Care and Maintenance

WARNING: Before you perform any cleaning or maintenance work, turn off the electricity at the main circuit breaker panel.

• Use a dry or slightly dampened clean cloth to wipe the surface of the fixture.
• Do not use any cleaners with chemicals, solvents, or harsh abrasives.

Troubleshooting

supply is on.
There is a faulty switch.| Test or replace the switch.
There is a faulty wire connection.| Check the wiring.
There is a faulty driver.| Replace the driver.
The fuse blows or the circuit breaker trips when the light is turned on.| There are crossed wires or the power wire is grounding out.| Check the wire connections.

Questions, problems, missing parts? Before returning to the store, call Customer Service
8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
Retain this manual for future use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>