Widoo Intelligent Technology WD-01CE Smart Rain Forest Spray System User Manual

Widoo Intelligent Technology WD-01CE Smart Rain Forest Spray System

Place the host
When placing the host, you can choose direct placement, suction cup fixation, or hook. Please note the correct direction.

Connection method

When DIY connecting pipes,Wearing gloves will be easier to operate.

Operation process
Download APP>> Registration&login>» Connect device >> Set device

Download APP
Search “Smart Life-Smart Living” by your mobile phone, download and install the APP.

• The following permissions need to be allowed
  • “Smart life” would like to find and connect to devices on your local network.
  • Allow “Smart Life” to use your location while Using App.
  • “Smart Life” would like to send you Notifications.
  • “Smart Life” would like to send you Critical Alerts.
  • “Smart Life” would like to Access Your Home Data.

Attention
“Smart Life” would like to Use Bluetooth.

Registration and Login

You can register with your mobile phone numbers or email. If you have already registered an account, you can enter your account and password to log in.

Connect device

Plug in the type-c power supply, the blue signal indicator lights up, and different flashing modes represent different states, as follows:

1. Always on: Not connected/offline
2. Flashing: To be connected
3. Off: Connected

• Make sure that both WiFi and Bluetooth of the mobile phone are turned on, and the WiFi signal is 2.4GHz.
• Wait for 20 seconds and then open the “Smart Life” APP. Some phones can automatically connect to the device, Enter the wireless network password to add a device (STEP1-STEP7) Some mobile phones cannot automatically connect to the device, and you need to add the device manually. (P1–P2),then follow STEP4–STEP7. After networking, you can enter the device interface,

If the device still can’t connect to the network, refer to the following:

1. WiFi and Bluetooth are both turned on and are in a 2.4GHz network.
2. The router has a good signal and can connect to the Internet normally.
3. When installing the APP, all permissions have been allowed and the wireless network password is correct.
4. The device is in distribution mode and the signal light is flashing. If the signal light is not flashing, Hold the key for 5 seconds to reset the device,Then reconnect again.

Manual control mode

Click the app button or the device touch button to manually turn on or turn off the water pump.

Delay mode

• Hold the button in the app software for 3 seconds to enter the countdown mode. You can set the time, ad the water pump after running according to the time you set. stop

Schedule Watering

Custom mode
Under custom mode, you can set the starting time, watering time and working duration of the device.

Interval mode
Under the interval mode, the device will work for a while, stop for a while and then work again(based on your setting).and the working way will go on cycles.

Program management

You can enable or disable the program by sliding the switch; If you need to delete the program, you can slide the program to the left and click the trash can on the right to delete it.

• Rated voltage: 5 V
• Size: 1308743 (mm)
• Lift:22 m
• Rated current: 1A
• Net weighe: 180 g
• Suction:21.5m
• Noise range: s50db[30cm)
• Maximum pressure: 2 30psi (200kpa)
• Wifi: 2.4 Ghz
• Ambient temperature: 4~45°C

Note

1. Check the nozle regularly. If it is blocked, please clean it in time to get the best spray effect.
2. The position of the water container is relatively lower than the flowerpot to prevent the water in the bucket from directly flowing into the flowerpot without starting up in the sealed pipeline.
3. WD-01CE is only used for intermittent watering, and can not be used as a pump to continuously transport fluid medium for a long time, otherwise it will seriously reduce the service life of the main engine diaphragm pump.

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any i nterference received,including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the party responsible for Compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates use s and can radiate radio frequency energy and, if not installed and used in accordance with the in structions, may cause harmful interference to radio communications. However, there is no guar antee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help with an important announcement.

Radiation Exposure Statement
To comply with FCC RF exposure compliance requirements, this grant is applicable to only mobile configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>