bettabot Betta 2 Smart Pool Skimmer Owner’s Manual
- June 8, 2024
- bettabot
Table of Contents
Betta 2 Smart Pool Skimmer
Owner’s Manual
888-692-3882 (888-MyBetta)
Important Safety Instructions
- DO NOT SWIM while Betta is working in the pool. Take it out of the pool and keep it at a cool place under the shade when the pool is in use.
- Betta Smart Pool Skimmer is NOT a toy. Keep it away from children.
- Be sure to watch your steps and maintain your balance when working by the pool side.
- Do not use while other pool cleaning devices are in the pool.
- During swimming season, keep Betta in the pool all the time unless the pool is in use or the unit needs cleaning or service.
- Do NOT leave Betta in a hot and dry spot out of the pool unattended to avoid severe damage to the unit.
- Do NOT wash Betta using pressure washer as it would cause damage to the unit.
About Betta
Thank you for purchasing Betta the smart pool skimmer. Betta will provide you
with years of reliable service when it is well taken care of and maintained
properly. Be sure to read all the instructions in this manual to fully
understand how to use and care for the unit.
Betta is a smart pool skimmer that mostly runs by itself. It works as a pool
surface cleaner/skimmer and is powered completely by the solar panel that
charges the battery built inside. Betta is fully self-driving unless
controlled by the optional remote included. It has a control system with
various sensors including a Gyro scope to guide itself while maneuvering on
the pool surface. The unit picks up floating debris in its path and collects
it into the removable collection basket inside. Typically, every 3-4days, you
can remove the unit from the pool , empty the collection basket, and clean
the unit using water hose. Place it back to the pool and it starts working
right away after cleaning is done.
There is no need to plug in to charge. The unit has a high-capacity top solar
panel that charges the battery when there is sunlight and manages the
operation automatically based on the battery charge. The unit runs 100% on
solar energy and does NOT have any AC/DC/USB charging ports.
Components
Parts List
| 1. Cover Lock | 7. Solar Panel |
|---|---|
| 2. Distance Measure Sensor | 8. Power Switch |
| 3. LED Status Indictor | 9. Cover |
| 4. Guide Wheel | 10. Debris Collection Basket |
| 5. Propeller | 11. Debris Intake Impeller |
| 6. Anti-stranding Bar | 12. Handle |
Using the Pool Cleaner
4.1 Using the unit for the first time
Note: Betta ONLY takes solar charge when power switch is ON
Be sure to watch your steps and maintain your balance when working by the pool
side.
Step 1. Slide the power switch to the position that you can see “ON” mark to
turn on the unit.
LED status indicators at front will flash and then the propellers and impeller
will start running.
Step 2. Place Betta into your pool and it will start moving and cleaning the
pool’s surface.
Betta runs in either Auto Mode or Remote Control Mode during operation.
Auto Mode
Betta is designed and programmed to be fully self-driving. It maneuvers and
guides itself by reading the sensors and managing operations and charging
smartly on its own. By default, the unit will be working in Auto Mode unless
it’s operated by the remote control.
Remote Control Mode
You can manually control Betta’s movement and travel path in the pool using
included remote control when needed. For example, if you want Betta to go
left, just press and hold the left button on the remote. Remote Mode gives
you fast control to move Betta wherever you want.
4.2 Remote Control
Pairing Betta with a New Remote
The remote control packed with Betta has been paired in the factory.
You only need to do this step if it doesn’t work, or you replaced it with a
new one.
First, slide the power to “OFF” position to turn off the unit. Second, slide
the switch to “ON” to turn it on. Press any button once on the remote control
within 5 seconds after you turn on the unit. Test the buttons on the remote
after the 5 seconds and see if the unit is moving accordingly. If yes, the
paring completes. If not, repeat this process from the beginning. If no
success on paring, please contact Betta customer service.
Using Remote Control
You should be able to use the remote control out of the box since it’s paired
with your Betta in the factory. You only need to pair it if it doesn’t work,
or you replaced either the Betta unit or the remote control.
Press any button on the remote control. Betta will instantly enter Remote
Control Mode.
Press and hold the left button to move Betta left, press and hold the right
button to move Betta right, so on and so forth.
To go back to Auto Mode, press the middle button down for 2 seconds, and Betta
will go back to Auto. Also, if you do not operate Betta with the remote
control for 2 minutes, it will go back to Auto Mode by itself.
4.3 LED Light Status Indicator
LED light status indicators (one on each side at front) will show the
operation status information of working conditions of the unit.
Standard Mode: lights flash in Green.
Status: there is enough power, the unit will keep running.
Intermittent Mode: lights flash in Red.
Status: the battery is low; the unit is running at irregular intervals in
attempts to locate sunlight where it can be recharged.
Sleep Mode: all indicator lights are off.
Status: the battery is very low, or battery becomes completely discharged.
Remote Mode: lights are in steady Green.
Status: the unit is controlled manually via a remote control.
Strand Mode: lights flash in combination of Red and Green.
Status: the unit’s propellers or impeller is not working properly, most likely
it has been stuck by obstacles or cannot run freely. In this case it will stop
running automatically. The unit will try to restart every 20 minutes when it
is in Strand Mode. 
4.5 Battery Run Time during Winter
During winter months, the battery may not get a full charge because the
sunlight is not as strong as during summer. Therefore, you should expect Betta
to have a shorter run time than in the summer. Even in a sunny winter climate
like CA, FL, and AZ, you will not get as fast charge as in the summer, and a
full charge will need a longer period.
Cleaning and Storage
Empty Collection Basket and Cleaning
Be sure to watch your steps and maintain your balance when working by the pool
side.
Clean the debris collection basket every 2-3 days to keep Betta running at
high efficiency.
- Use the remote or waiting until Betta is close to the shallow end of the pool where you can have safe access to Betta.
- Keep it flat when you lift it up by using two hands – one on the front handle and the other on the lift grip at the rear end to avoid debris getting out of the basket. Leave Betta on a flat surface to rest the unit.
- Slide power switch off.
- Unlock the cover lock. Lift the basket handle up to remove the basket out of the unit and empty the debris.
- Rinse the basket out with water hose until it’s completely clean.
- Put the basket back in the unit, secure the cover lock, and turn power on.
- While cleaning the basket, you may also clean the solar panel. You may see some white residues on the solar panel which are chemicals and minerals from pool water.
Wash the residues out using water hose and wipe clean with soft dry cloth. Do NOT use pressure washer to clean or any tools to scrape or brush the panel to avoid damages.
Winter and Long-Term Storage
If you are closing your pool for the winter, please remove Betta from the
pool. Rinse Betta off with hose water, let it completely dry, and keep it
indoor at room temperature in a dry place away from high heat. Before the
first use of the next season, check all the parts of Betta for signs of
trouble before putting it back in use. Turn power on when ready to use.
Troubleshooting
Note: Betta ONLY takes solar charge when power switch is ON
Below is some info that should help your daily use of Betta.
| Problem | Possible reason | What to Do |
|---|---|---|
| Not running at night | The unit is in Sleep Mode. The status lights are off, | |
| indicating the battery level is very low or completely discharged. | Leave the |
unit in the pool. After sunrise the next day, the unit will start running inry
intervals in attempts to locate spots with good sunlight where it can be
recharged. You may manually place it in the direct sunlight to charge it
faster.
Not running during the daytime| Scenario 1: The unit is in Intermittent
Mode—the status lights are flashing in Red, indicating the batter is low.| You
may leave it as is in the pool, the unit will run in intervals in attempts to
locate sunlight where it can be recharged.
Scenario 2: The unit is in Sleep Mode. The status lights are off, indicating
the battery level is very low or completely discharged.| Try to place it in
the spot that has direct sunlight in the pool and wait until it gets some
charge.
Scenario 3: The unit is in Strand Mode. Status lights are flashing in Red and
Green indicating Betta is stuck at some structures, such as stairs, stools, or
propeller/impeller is strapped by something.| • Be patient and wait for a few
minutes. The unit will try restarting every 20 minutes when it is in Strand
Mode.
• Ensure that the basket is in place, and the Cover Lock is properly secured.
• Check propellers and Impeller for dirt, string, or hair.
Unit only runs a
short time when sunlight is sufficient| 1)The solar panel has residues.
2)Propeller or Impeller is strapped.| • Clean the solar panels.
• Ensure propellers and Impeller are turning freely.
Warranty Information
Betta is designed to work in fresh water or salty water up to 5000 P.P.M. The
unit comes with 1Year Manufacturer
’s Warranty from the date of purchase. Using the unit in sea water pools will
void the warranty. If you have any issues or concerns, please contact us
directly. Betta honors extended warranty ONLY through Betta Care. Any other
offers from third-party retailers will not be serviced by Betta directly. If
you have any questions about Betta warranty, please contact us at
info@BettaBot.com or
888-692-3882.
Warranty Registration
scan the QR code below
www.bettabot.com/pages/warranty-registration
Extended Warranty (Betta Care)
scan the QR code below
www.bettabot.com/pages/warranty
Customer Service
Phone: 1-888-692-3882 (1-888-MyBetta)
or 562-579-0001 | Fax:
562-579-0008
Live Chat: Any webpage on www.BettaBot.com
Email: info@BettaBot.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>