embed Aluminum Blinds with Hidden Brackets Instruction Manual

embed Aluminum Blinds with Hidden Brackets

Thank you for choosing Springs Window Fashions. Your window treatment has been custom-sized based on your specifications and created with the highest standards of quality and craftsmanship. Follow the easy step-by-step instructions to install your window treatment. Should you need additional support, please feel free to call our Customer Service Center at
1-800-221-6352 or email us at windowfashions@springswindowfashions.com. We are glad to help you.
For additional safety information in Canada, contact 1-866-662-0666.

HOW TO INSTALL

Inside, Outside, or Ceiling Mount Aluminum Blinds with Hidden Brackets

Tools Needed

Finished looks

• Inside Mount OR Ceiling Mount
• Outside Mount

Everything needed to install your blind

1. Blind
2. Wand
3. Cord Cleats
4. Installation Brackerts
5. Optional Hold-down Brackets
6. Optional Extension Brackets
   Brackets:
   Headrail Widths:
   Brackets
   up to 60″ use………….2
   up to 96″ use………….3
   up to 144″ use………….4
   up to 192″ use………….5

Determine bracket location

• Blinds with 1″ slats, 21″ and wider, with standard or reversed controls
  Persianas con tablillas de 1” (2.5 cm), de un ancho de 21” (53.3 cm) o mayor,

• Blinds with 1” slats, 14” to 20 15/16” wide, with standard or reversed controls
  OR

• Blinds with 1/2” slats, 14” and wider, with standard or reversed controls

• Blinds with 1″ slats, under 14″ wide, with center tilt
  Persianas con tablillas de 1” (2.5 cm), de un ancho de menos de 14” (35.6 cm), con inclinación central

Set install brackets into available open spaces on the headrail, avoiding the cradle and tilter. If more than two brackets, equally space the brackets across the headrail for maximum support. For additional blind types, see details on next page.

• Blinds with 1″ slats, all blind widths, with same side controls
  OR

• Blinds with 1/2″ slats, all blind widths, with same side controls

• Blinds with 1″ slats, under 14” wide, with center tilt, standard or reversed controls
  OR

• Blinds with 1/2″ slats, under 14″ wide, with center tilt, standard, or reversed controls

Set install brackets directly on top of the cradles. If more than two brackets, equally space the brackets across the headrail for maximum support.

Mark bracket location on headrail

Place a piece of tape on the headrail at the center of each bracket location. Mark the center of the bracket on the tape. Remove the brackets from the headrail.

Mark location of blind

INSIDE MOUNT

Place headrail into window opening and transfer the pencil mark. Remem-ber to keep headrail level even if your window is not. Remove tape after pencil marks have been transferred.

OUTSIDE MOUNT

Place headrail into window opening and transfer the pencil mark. Remember to keep headrail level even if your window is not. Remove tape after pencil marks have been transferred.

Drill holes

INSIDE MOUNT

OUTSIDE MOUNT

Screw in brackets

INSIDE MOUNT

OUTSIDE MOUNT

Brackets must be installed on a level surface and aligned from top to bottom and front to back

Optional: Projection brackets

Mount blind on brackets

Place front of headrail onto the hooks on the front of the installation brack- ets and roll the headrail back until you hear the headrail snap into place

Optional: Hold-down brackets

INSIDE MOUNT

OUTSIDE MOUNT

Install cord cleat

Install cord cleats 6” to 12” apart at a height out of reach of children.
Wrap cords around cleats when not in use.

Optional: Attach Tilt Wand

• To connect the wand with the wand connector clip, pull the end of the connector clip through the hole on the end of the wand. Locate the hole at the top of the long groove on the wand tilter stem and insert the wand connector clip. Pull the wand connector clip down and to the short side of the tilter stem and snap on.

Blind operation: opening and closing the slats

Close the slats in the direction desired for light control and privacy. Pull wand into room slightly for easiest operation. Rotate wand to open or close slats.

Cord lift blind operation: raising and lowering

RAISING THE BLIND

Tilt open slats and pull lift cords straight down to raise the blind. At the de-sired height, move cords toward the outside edge of the blind then gently release the cords to engage the lock.

LOWERING THE BLIND

Open the slats a little if closed.
Pull lift cords toward the center of the blind to release the lock. Feed the cords into the blind to lower.

Blind removal

For blind removal insert a flat head screwdriver between the back of the headrail and the metal tab on the bottom of the mounting bracket. Rotate the screwdriver until the bracket disengages from the lip on the back of the headrail.

Cleaning instructions

• Use warm water and mild non-abrasive liquid soap to clean slats.
• Use a feather duster to remove dust from slats.
• Or, use the brush attachment of a vacuum to remove dust from slats.

For additional assistance
please contact our Customer Service Center at 1-800-221-6352.
Springs Window Fashions LLC
P.O. Box 500, 8467 Route 405 South Montgomery, PA 17752

References

• Springs Window Fashions | Springs Window Fashions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>