tp-link LS1005G Gigabit Desktop Switch Installation Guide

© 2023 TP-Link 7106510814 REV2.0.2

Installation Guide

5/8-Port Gigabit Desktop Switch

LS1005G/LS1008G

LED Explanation

Power

            On: Power on
Power    Off: Power off

Link/Act

1. Link/Act (Green)
   On: Running at 10/100/1000Mbps
   Off: No device is linked to the corresponding port
   Flashing: Transmitting/receiving data

Note: For simplicity, we will take LS1008G for example throughout this Guide.

Connection

1. Power Adapter
2. Power LED
3. Ethernet Ports (1-8)
4. LS1008G
5. Internet
6. Router
7. WAN Port
8. LAN Port
9. PC

Frequently Asked Questions (FAQ)

Q1. The Power LED is not lit.

The Power LED should be lit when the power system is working normally. If the Power LED is not lit, check as follows:
A1: Make sure the power adapter is connected to the switch with power source properly.
A2: Make sure the voltage of the power supply meets the requirements of the input voltage of the switch.
A3: Make sure the power source is ON.

Q2. The Link/Act LED is not lit when a device is connected to the corresponding port.

It is recommended that you check the following items :
A1: Make sure that the cable connectors are firmly plugged into the switch and the device.
A2: Make sure the connected device is turned on and works normally.
A3: The cable must be less than 100 meters long (328 feet).

Specifications

General Specifications

Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full Duplex)
Gigabit Ethernet: 2000Mbps (Full Duplex)
Network Media (Cable)| 10Base-T: UTP category 3, 4, 5 cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
100Base-TX: UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
1000Base-T: UTP category 5e cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
Interface| 5/8 10/100/1000Mbps Auto-Negotiation RJ45 Ports
LED Indicators| Power, Link/Act LED
Transfer Method| Store-and-Forward
MAC Address Learning | Automatically learning, automatically aging
Frame Forward Rate| 10Base-T: 14881pps/Port
100Base-TX: 148810pps/Port
1000Base-T: 1488095pps/Port
Wall Mountable| Yes
Distance Between Mounting Holes| LS1005G: 38mm
LS1008G: 48mm

Environmental and Physical Specifications

To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community.
For technical support and other information, please visit https://www.tp- link.com/support, or simply scan the QR code.

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.

The original EU declaration of conformity may be found at https://www.tp- link.com/en/support/ce/

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.

The original UK declaration of conformity may be found at https://www.tplink.com/support/ukca/

Safety Information

• Keep the device away from water, fire, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended.
• Adapter shall be installed near the equipment and shall be easily accessible.

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

References

• TP-Link Community
• CE Regulatory Compliance | TP-Link
• TP-Link Product Support - Wireless Networking Equipment Support
• Regulatory Compliance | TP-Link

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>