Guangzhou Huizhi Trading X02-1 Wireless Controller User Guide

Guangzhou Huizhi Trading X02-1 Wireless Controller

Button Layout

1. Screenshot Button
2. 2. – Button
3. Home Button
4. + Button
5. Light Button
6. Left Stick / L3 Button
7. Direction Button
8. Y Button
9. X Button
10. A Button
11. B Button
12. Right Stick / R3 Button
13. LED1-LED4 Indicator
14. Light Ring
15. M2 Button
16. Vibration Button
17. M Button
18. Turbo Button
19. Reset Button
20. M1 Button
21. R Button
22. ZR Button
23. L Button
24. ZL Button
25. Type-C Charging Interface

Specifications

1. Working voltage: DC3.7-4.2V
2. Input voltage/current: DC5V/1A
3. Charging time: about 3 hours
4. Continuous running time: >10 hours
5. Battery capacity: 1000mAh

Connection

Wired Pairing

1. In TV mode, connect the controller to the dock of switch with a USB cable.
2. After the wired connection is successful, unplug the USB cable, and the controller will automatically connect wirelessly.

Wireless Pairing

1. Press the Switch power button to start the switch.
2. After booting up, do the following: first step enter the “Controller Settings – Change Grip / Order” page, press the “Right” of “Direction“ and “Home” button til the light of “Home” button turns red and flashes quickly.
3. After successfully connected, the light of “Home” button will always light on.

Reconnection
After the first successful connection, short press the “Home” button, the controller will turn on and automatically reconnect to the Switch. After successfully connected, the 4 LED lights indicate the corresponding game player.

Connection Problem
If the controller can not connect with the Switch, please try the following solutions:

1. Fully charged via USB cable if power low then attempts to connect.
2. Try connecting to the Switch via a USB cable first, then connect wirelessly.

In this step, please make sure that the Switch has turned on the wired connection mode, as pictures shown (Setting – Controllers and Sensors – Pro Controller Wired Communication

Clear the switch connection cache if 1&2 methods can not work out, as pictures shown(Setting – System – Formatting Options – Reset Cache). Too much bluetooth data may cause connection error. In order to avoid this situation, clearing the Bluetooth data before connected is necessary.

If it still can not connect after tried the above methods, you can reset it by pressing the “Reset” button on the back of the controller.

Light

Normal Mode
When the controller is turned on for the first time, all lights are always on.

Colors： Press the “Light” button once to change the color of lights successively(red-orange-yellow-green-blue-cyan-purple-off).
Note: In any mode, press the “Light” button once, all lights will return to normal mode.

Rainbow Mode
In “normal mode” or lights off state, press the “Light” button twice，all lights enter the rainbow mode and always on.

Single Color Gradient Mode
In “rainbow mode”, press the “Light” button twice，all lights display in the same color and change automatically.

Double Color Gradient Mode
In “single color gradient mode”，press the “Light” button twice，all lights display in two colors and change automatically.

Lights Off
In “double color gradient mode”，press the “Light” button twice，all lights go out.

Brightness Adjustment
In any mode，press the “Light” button for 1 second to start adjusting the brightness (0%-25%-50%-75%-100% cycle).

Note: The controller will vibrate when you change the lights.

No Dead Zone Mode

Description
In this mode，there is no dead zone in the center area of the corresponding joystick.when setting or canceling，press the “M+L3” button is only valid for the “Left Stick”, press the“M+R3” button is valid only for the “Right Stick”.

Seting
Hold the “M” button then press the “L3/R3” button to turn on the “no dead zone mode” of the corresponding joystick .

• Note 1: The controller will vibrate once when you when you set the mode.
• Note: The mode will reset every time the controller is restarted.

Cancel After setting，Hold the “M” button then press the press “L3/R3” button to cancel the “no dead zone mode” of the corresponding joystick

Note 1: The controller will vibrate twice when you cancel the mode.

Button Assaign Function

Buttons can be set A / B / X / Y /R / ZR / L / ZL / L3 / R3 and direction buttons and left or right joysticks (joystick counts as eight keys).

Seting

1. Hold the “M” button and press any of “M1/M2” button to enter the programming mode.
2. Then input the button or button combination you want to set.
   • Eech programmed button(M1/M2) can record up to 21 inputs. (Each press of function buttons is regarded as an input)，When the input exceeds 21 times，the programming will automatically end.
3. When youʼre done , press the “M1/M2” button that was pressed earlier to end the programming.

Note: The controller will vibrate when you when you start or end the programming.

Cancel

Method a: After entering the programming mode, directly press the “ M1/M2” button that was pressed earlier to exit without setting any buttons (at this time，“M1/M2” button is empty and there is no function).

Method b: Press the “M” button for 5s to reset the assaign function.

Note: The controller will vibrate when you when you cancel the assaign function.

Turbo Function

Setting and Cancel

1. Hold the “Turbo” button and press any of A/B/X/Y/L/R/ZL/ZR button (for the first time) to turn on the turbo function.

2. Hold the “Turbo” button and press any of A/B/X/Y/L/R/ZL/ZR
   button(for the second time) to turn off the automatic turbo function.

   • Hold the “Turbo” button for 5 seconds to cancel all turbo function.

Note1: The controller will vibrate when you turn on or turn off the turbo function.
Note2: Turbo function will reset every time the controller is restarted.

Turbo Speed Adjustment

• there are 3 gears of turbo speed: 5/12/20 times per second.
• Hold down the “Turbo” button and move the “Right Stick” up to increase the TURBO speed.
• Hold down the “Turbo” button and move the “Right Stick” down to reduce the TURBO speed.

Note: The controller will vibrate when the adjustment is successful.

Vibration Adjustment

1. There are 5 levels of vibration intensity on the controller: 0%，30%， 50%, 100%.
2. Press the “Vibrate” button to adjust the vibration intensity of the controller. It will cycle to 0% after reaching 100%.

Note: The controller will vibrate when the adjustment is successful.

Status

Low Battery
When the battery power is low, the LED1-LED4 indicator lights flash quickly.

Charging

• When the controller is charging, the LED1-LED4 indicator lights slowly.
• When the power is full, the LED1-LED4 indicator lights will be off.

Wake Up
After the first successful connection, press the “Home” button to wake up and reconnect (other buttons can not wake up).

• Binbok Marketing
• @BINBOKOffcial
• Official Homepage : binbok.com （Register on this web to activate aftersales.）
• support@binbok.com Business
• Contact: contact@binbok.com

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet the general RF exposure requirements. The device can be used in portable exposure conditions without restriction

References

• BINBOK - Born to Game!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>