BAUHAUS 50×75 cm LED MIRROR Installation Guide
- June 5, 2024
- BAUHAUS
Table of Contents
BAUHAUS 50×75 cm LED MIRROR
NOTE: To be installed by an authorized electrician only.
Outils / Gereedschap
Spareparts
INSTALLATION
The height is based on a distance of 190 cm between the floor and the upper edge of the lamp. We recommend to check which height fits you the best before you drill holes into the wall.
The wall plugs included are only to be used in brick- or concrete walls. If you have another type of wall you should buy the wall plugs required for that type of walls in your local DIY store. All screw holes you drill in the wall in a bathroom should be sealed with silicone. We recommend that you put silicone into the screw hole before you insert the wall plug. Then you put silicone into the wall plug before you fix the screw into the wall plug.
- SIZE LIGHT 60×75 cm 1xLED Strip-14.3W Max 3744Lm Max, 3000K/6000K
- VOLTAGE TOTAL 230V ~ 50Hz 14.3W
- SIZE LIGHT 80×75 cm 1xLED Strip-15.6W Max 4368Lm Max, 3000K/6000K
- VOLTAGE TOTAL 230V ~ 50Hz 15.6W
- SIZE LIGHT 90×75 cm 1xLED Strip-16.1W Max 4680Lm Max, 3000K/6000K
- VOLTAGE TOTAL 230V ~ 50Hz 16.1W
- SIZE LIGHT 100×75 cm 1xLED Strip-16.7W Max 4992Lm Max, 3000K/6000K
- VOLTAGE TOTAL 230V ~ 50Hz 16.7W
- SIZE LIGHT 120×75 cm 1xLED Strip-17.6W Max 5616Lm Max, 3000K/6000K
- VOLTAGE TOTAL 230V ~ 50Hz 17.6W
NOTE: To be installed by an authorized electrician only.
Push the button shortly
The light will change between warm, cold or off
Hold down the button
The light will change the brightness.
The button does not work with wet fingers or if the mirror is moist.
Push the button shortly: The light will change between warm, cold or off. Hold
down the button: The light will change the brightness.
The button does not work with wet fingers or if the mirror is moist.
Congratulations with your new LED light mirror. Here you have some good advise how to install and maintain the mirror in the best possible way.
Generally:
You prolong the lifespan of your bathroom furniture and mirrors if you secure
a good ventilation in the bathroom. A good ventilation system reduces humidity
after you have taken a bath or a shower.
Important:
Do not spray water directly on the mirror. The mirror is well protected
against humidity, but should not be exposed to direct water splashes. Consider
fx to install a fixed shower enclosures instead of a shower curtain. Do not
place the mirror immediately next to a shower or bathtub, there should be at
least 60cm distance between your mirror and the shower or bathtub.
Installation:
The wall plugs included are only to be used in brick- or concrete walls. If
you have another type of wall you should buy the wall plugs required for that
type of walls in your local DIY store. All screw holes you drill in the wall
in a bathroom should be sealed with silicone. It is important that You follow
the rules and regulations of your country regarding installations in
bathrooms, and the supplier takes no responsibility if the rules and
regulations has not been followed.
Cleaning of the mirror:
Do not use aggresive or polishing cleaning detergents or rough or polishing
sponges during cleaning. This can scratch or damage
the surface on the mirror. Keep the mirror dry, clean and free from grease,
oil and detergents. On all our mirrors we have sealed
the edge to prevent the mirror foil to get in contact with humidity so it
starts to rust. Generally, are mirrors not well suited for humid environments,
so good ventilation as described here above, will prolong the lifespan of your
mirror. It is important that you keep the edges of the mirror dry and that you
remove eventual detergents after cleaning from the edges of the mirror,
especially in the bottom. Detergents, water or alcohol can after some time
start to dissolve the edge sealer and the mirror foil can start to rust.
Electricity in a bathroom
230V light fixtures or sockets, regardless of the IP grade and connector box, can not be installed in zone 0 or zone 1.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>