KERMI B20-S M Bathroom Radiator Instruction Manual

**KERMI B20-S M Bathroom Radiator Instruction Manual

**

AssembLy instructions

1. technical data

2. Legend
   A Heating area
   B Centre connection offset (LR0 1M only)
   BH Actual construction height
   BL Actual construction length
   Bt Construction depth
   G Weight
   H Clearance: fitting to connection sleeve
   L Drill hole spacing
   n Heater exponent
   n Hub clearance
   P Heating capacity
   V Water content

3. Front and side view

4. Drill hole spacing
   Be Bottom edge connecting thread
   Please leave assembly instructions with the end consumer!

5. Connections
   Connections: 4 or 2 x G 1/2 (internal thread) downwards.
   Venting: G 1/2 (internal thread) to rear.

6. Vi operation
   Operating pressure: max. 10 bar
   Test pressure: 13 bar
   Operating conditions: hot water up to 110°C

7. Manufacturer‘s instructions

Permissible usage
The heater may only be used to heat indoor areas and dry damp textiles. Each and every other usage is not purpose related and is therefore not permissible!
important
Operating and water conditions should be observed according to DIN 2035. Implementation in closed heating circuit systems.
important
Heaters supplied are intended solely for room heating. They are not suitable as seating or as climbing or mounting aids

Depending on the flow pipe temperature the heator surface may heat up to 110°C.
Risk of burning!

Maintenance and cleaning
Bleed the heater following commissioning and extended interruptions in operation. For cleaning purposes, only mild and non-abrasive commercially available cleaning agents may be used. complaints In the event of damage, contact your specialised
craftsman!
Attention!
Commission qualified tradesmen only to perform assembly and repair jobs to assure that your rights according to the warranty of quality law are not nullified.

Accessories

According to the currently valid sales documentation

Assembly procedure

1. Please read the instructions carefully prior to assembly!

2. transport and storage shall only be carried out inthe protective packaging!

3. Mounting location
   important
   In the case of electro auxiliary operation the safety areas prescribed in VDE 0100 part 701 must be observed (at the heater side outside bath tub or shower area, socket and timer at least 0.6 m away at the side). Please also observe all local regulations.
   For LS010/LR010:
   On single pipe systems, the electrical heating element can be built in without changing the connection geometry. On two-pipe systems, retrofitting is only possible when the connection geometry is changed. A T-piece is mounted for this purpose on the return pipe side for the electrical heating element. The connection location is altered by the T-piece when an electrical heating element is connected and mounted!

4. inspect the package content for completeness and any possible damage! A1 Heater LS0 10/1 M or
   A2 Heater LR0 10/1 M
   B Wall holder
   c Sliding component
   D Retaining cap
   e Cover
   F Dowel 6 x 60
   G Dowel 10 x 60
   H Washer
   i Screw M6 x 35
   J Screw M5 x 12
   K Vent plug
   L Inclined base (LR010 / LR01M only)

5. Have all tools at hand as required

6. important:
   check the bearing surface for adequate supporting capacity! Observe spacing rquirements: heater – side wall / room ceiling min. 50 mm! Drill by rotation and not impact in the case of low strength materials such as hollow bricks, lightweight or aerated concrete.

7. Drill two horizontal dowel holes (top and bottom wall holder):
   Drill two dowel holes each according to the table (I Technical data) and diagram (IV Drill hole spacing) at the top and bottom at a distance of „L“, ø 10 mm, depth 60 mm and insert dowels (G) in the drill holes.
   Danger to life !
   Be careful not to damage any water or gas piping, or live cables when drilling!
   **** Secure wall holder (B) and if necessary inclined base (L) [LR0 10/LR0 1M only] with screws (F) and washers (H). The slot for adjusting the wall clearance must hereby be aligned downwards.

8. Allign the wall holder(B) horizontally.

9. Mount the sliding component (c).
   Insert the sliding components (c) in the wall holder (B) and insert the screws from below. (J)

10. Secure heater
    Press the heater against the sliding components between the second and third pipe from the top (c) and secure with retaining caps (D) and screws (i). In doing so, centre the heater in relation to the wall holders(B). Press the heater against the botton sliding components (c) drücken, mit Haltekappen (D) and secure with screws (i). Adjust the wall clearance and assure the heater is plumb before tightening the screws (J) und (i) to fix the position.

11. Attach the covers (e).

12. Screw in the vent plugs (K) at the top left .

13. connect the heater at the water side with
    commercially available screw fittings. Check the system for leaks!

14. Dispose of packaging material via recycling systems.
    Send scrap heaters with accessories for recycling or orderly waste disposal as required (observe regional regulations.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>