CHORD Mojo Portable DAC Headphone Amplifier Instruction Manual
- June 8, 2024
- chord
Table of Contents
CHORD Mojo Portable DAC Headphone Amplifier Instruction Manual
Cleaning and care instructions:
Mojo requires no special care other than common sense. Spray window cleaner
(clear type) may be used (if first sprayed onto a soft cloth) to remove
surface blemishes such as finger marks from the metal casing. Never spray
directly onto the converter and never use abrasive cleaning, use only a lint
free soft cloth. There are no user serviceable parts in Mojo. It should be
serviced only by Chord Electronics Limited or their expressly approved service
agents.
Warranty:
Mojo comes with a comprehensive 12 month warranty (conditions apply) please
register online. Should you need to make a claim under warranty you must
contact the retailer or distributor to arrange collection.
Mojo diagram:
Charging:
Mojo can be charged from any 1 Amp USB port using the cable supplied or any
other USB A to micro USB B type cable. Just plug the cable into the connector
with the battery symbol.
Please note that the USB charger or computer port must be capable of
supplying at least 1Acurrent.
Charging is indicated by a white light under the charging port. When Mojo is
fully charged (approximately 4 hours) the light will switch off. We recommend
charging with Mojo switched off. Charging with Mojo switched on and playing is
possible, but the time taken to fully charge will be considerably longer and
depending on volume level and headphone load the battery. It is possible that,
when using headphones of high load, the battery may take extremely long to
fully charge.
It is normal for Mojo to become warm when charging especially if switched on
and playing at the same time.
Battery State Indicator:
In order to determine Mojos state of charge please refer to the LED indicator below the charging USB port:
Switching On/ Off
Press and hold down the power button for 2 seconds to switch Mojo on or off.
Please note you must wait 5 seconds between switching on or off before the
power button will respond again.
Volume Indication
The + and – volume balls are illuminated to indicate the volume setting. The
standard range is from brown to white for maximum volume.
At both minimum volume and maximum volume the range has been extended and the
balls illuminate specially to indicate this.
At minimum volume the + ball will remain brown whilst the – ball will continue
to change colour through the range from white back down to brown again. This
allows for finer volume adjustment when using in ear monitors.
At maximum volume the – ball will remain on white whilst the + ball will
change through the colours from red to white at maximum volume. This gives a
finer adjustment at very high volume
Sample Rate Indication
The power ball will illuminate when a digital signal is connected and show the
sample rate detected. The table below shows the colours and the corresponding
sample rate.
SAMPLE FREQUENCIES kHz
Brightness Setting
Mojo has two brightness settings for the illumination. Once Mojo has switched
on and finished the initialisation briefly press both volume buttons at the
same time to change between bright and dim modes.
Line Level Mode
To set the output level to 3V ( line level ) for connection to a preamplifier
press both volume buttons together when switching on the unit. Both volume
balls will illuminate light blue. This mode is not remembered so when you
switch off it will reset back to the previous volume stored for safety
reasons.
Memory
Mojo has a memory function that will store the volume level and brightness
settings even after the unit is switched off.
Audio Outputs
There are two 3.5mm stereo jack socket outputs for headphones. Both can be
used at the same time and will drive all headphones and in ear monitors (with
the exception of electrostatic) from 8 ohms impedance to 600 ohms. The outputs
are also short circuit protected.
Digital Inputs
Mojo has 3 digital inputs. 1 x TOSLink optical capable of playing 44.1KHz to
192KHz PCM and DSD64 in DoP format. 1 x 3.5mm COAX SPDIF capable of playing
44.1KHz to 384Khz PCM (768KHz special operation) and DSD64, DSD128 in DoP
format. 1 x micro USB capable of 44KHz to 768KHz PCM and DSD64, DSD128 and
DSD256 in DoP format. Driverless on Mac, Android and Linux OS. However Windows
Vista, 7, 8, and 10 will require a driver which can be found on our Mojo
webpage.
Digital Input Selection
Input selection is automatic. By default Mojo will always select USB input if this is plugged in. To use Optical or the 3.5mm Coax input please remove the digital USB input cable first ( you can still use the charging input ). If you have both coax and optical inputs connected at the same time, then the 3.5mm coax input will take priority over the optical. To use optical please unplug the coax input or switch off the digital source.
Using USB Digital Audio
Connection to the host computer
Connect Mojo to the host computer, phone, or tablet by inserting a USB lead
into any available USB socket. To support high sample rates (96Khz and above)
the USB socket on the computer must be USB 2.0 or above. Once connected insert
the other end of the cable into the USB audio socket on Mojo. If using a
Microsoft computer and the driver hasn’t been installed on your computer, an
automatic driver installation wizard may appear.
Note: If you want to avoid the automatic driver installation, please
connect Mojo to the computer after manually installing the driver.
Microsoft Windows Driver installation
The drivers for Mojo are available on our website. Please go to the Mojo
product page at
www.chordelectronics.co.uk. Drivers are
contained in zip files and must be extracted before installation.
Installing the driver on a Windows PC
Create a temporary folder on the hard disk of your computer (this can be on
your desktop). Double-click on the zip file contained on the CD to open it.
Select and drag all files in the temporary folder, this will automatically
unzip all the files.
Automatic installation
Connect Mojo to the PC. Following the negotiation process, the driver
installation wizard is automatically launched. Click on the button to proceed.
Choose automatic installation (as recommended) and proceed to next step.
Indicate the folder where you have previously unzipped the driver and proceed
to installation. Click on Continue. The installation will proceed to the end.
You may get warning messages indicating that the driver is not digitally signed – just click yes to continue installation. Click on Finish to complete the driver installation.
Manual installation
Sometimes it is necessary or advisable to install the driver manually. Without
connecting Mojo to the PC double-click the setup file contained in the
extracted zip file. The driver will automatically be installed on your PC. You
will find Chord Async USB 44.1kHz 192kHz device listed under Audio, Video and
Game controllers. Right-click to access the available actions. Select
“Uninstall”.
Configuring sound settings on a Windows PC
Configuring a PC with Windows Vista, Windows 7, 8 or 10
A Windows PC can use Mojo in three different ways: Direct Sound (DS), Kernel
Streaming (KS) and WASAPI. DS is suitable for players which can’t operate in
Kernel Streaming mode nor with WASAPI or for Internet streaming; KS can be
chosen (for better performance) with players which can operate in Kernel
Streaming mode (such as FooBar, Winamp, Monkey Media, JRiver). WASAPI (Windows
Audio Standard API) is a standard interface for audio players which allows to
get the same performance of KS with applications which can’t operate in KS
mode, at the cost of higher CPU load. Configuring for Direct Sound with
Windows Vista or Windows 7 Open control Panel and select Hardware and Sounds.
Under Audio, click on Manage Audio Devices. Set Chord Async USB 44.1kHz–768kHz
as default device. Then, click on OK.
Configuring for Kernel Streaming with Windows Vista or Windows 7
As for Windows XP, Kernel Streaming has no standard setting in Windows Vista
and Windows 7. KS must be selected in the specific player you choose to use.
For example, when using FooBar, with Mojo connected to the PC, go to the
File/Preferences/Playback /Output tab and select “Kernel Streaming Chord Async
USB 44.1kHz–768kHz” as output device. Foobar will require the KS add-on
installed first. Other players will require different settings.
Configuring for WASAPI with Windows Vista or Windows 7 Similar to Kernel Streaming, WASAPI cannot be directly accessed. WASAPI must be selected in the specific player you choose to use. For example, when using FooBar, with Mojo connected to the PC, go to the File/Preferences/Playback /Output tab and select “WASAPI: Chord Async USB 44.1kHz 768kHz” as output device. Foobar will require the WASAPI add-on installed first. Other players will require different settings.
Configuring Mac OS X
Open the System Environment Settings from the Start menu. Open the Sound options from the System Environment settings. Select the Output tab and confirm that Chord Mojo is selected as the default output device.
Sample Rate Setup
Open the Audio MIDI Settings options (Application – Utility – Set Audio MIDI).
Select the Audio Output tab in the Set Audio MIDI. Select the desired sample
frequency from the options given.
Android Device Operation
To use Mojo with an Android device you will need an ‘on the go’ cable ( OTG ).
This is a special cable that tells the Android device to run in host mode and
enable USB audio. Some devices with newer Android operating system ( 5 and
above ) will then play all audio into Mojo. If this does not work then you
need to download either USB Audio Player Pro or Onkyo HF player to enable USB
audio support. Both are available from the Google Play store.
Apple iPad/iPhone Operation
In order to use USB audio you will require an Apple device running iOS6 or
later and it needs the lightning connector rather than the old 30 pin
connector. You require the Apple camera connection kit which will enable a
standard USB connection from the lightning port. Use this cable with the short
USB to micro USB cable to connect Mojo. All audio will then play through Mojo.
Onkyo HF player can be used to support high resolution audio including DSD.
De-emphasis coding
Mojo will automatically detect when a pre-emphasized recording is being
played, and will set the correct de-emphasis filters in the converter section.
DSD decoding
DSD playback is supported using the DoP Standard 1.0 with 0xFA / 0x05 markers.
Please see the playback software manual for more details on configuring DSD
support.
Product Specification
HARMONIC DISTORTION < -103dB
SIGNAL TO NOISE RATIO >120dB
CHANNEL SEPARATION >125dB @ 1KHz
DYNAMIC RANGE 122dB
DIGITAL INPUTS 1 x 75Ω SPDIF 3.5mm 44.1KHz – 384KHz 1 x Plastic fibre
optic ( TOSlink ) 44KHz – 192KHz, 1 x USB 44KHz – 768KHz
HEADPHONE OUTPUTS 2 x 3.5mm Jack Sockets
OUTPUT IMPEDANCE 75mohm (short circuit protected)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>