SHARP DMR0173 Smart Microwave Oven Drawer with IoT Features Instructions

SHARP DMR0173 Smart Microwave Oven Drawer with IoT Features

IMPORTANT SAFETY INSTRUCTIONS

CAUTION FOR WIRELESS LAN

• If you are using in the following areas, the operation cannot be guaranteed: near Bluetooth wireless communications devices using the same frequency (2.4 GHz) as this product or specified low power wireless devices. There may also be issues in locations with devices, such as microwave ovens, that emit a magnetic field; as well as in areas with static electricity or radio disturbance, all of which can interfere with the W1-Fi signal.
• Wireless connection and performance cannot be guaranteed for all routers or housing environments.
• In the following places, it is possible the Wi-Ficannot reach or is disconnected: inside of a building made with conerete, reinforced metal, near an obstruction (e.g., a wall) or near a wireless communications device using the same frequency.
• Wireless LAN of this product corresponds to channels 1-13.
• It is not available to communicate with routers set up to other channels.

CAUTION FOR PERSONAL INFORMATION

(RELATED TO SECURITY)

• Using a wireless LAN device has the possibility of interception when using Wi-Fi, regardless of password setting.
• Depending on the location where you are connecting your oven, ensure you have the right/authority to connect the appliance to the available Wi-Fi network.
• If disposing of unit, giving or selling to a third party, be sure to Reset Wi-Fi Settings as described in this manual.
• The wireless LAN function of the unit should be initialized (reset) in case of handover to a third party to avoid illegal access from unauthorized parties.

MINIMUM REQUIREMENTS FOR Wi-FI/ROUTER SPECIFICATIONS:

• IEEE 802.11 b/g/n compatible WLAN
• 72.2Mbps receive and transmit PHY rate using 20MHz bandwidth
• 150Mbps receive and transmit PHY rate using 40MHz bandwidth
• 802.11i(WPA, WPA2). Open, shared key, and pair-wise key authentication services

SHARP HOME USE CONVECTION MICROWAVE DRAWER MODEL # SMD2499FS

• Contains FCC: RX3-B01
• Contains IC: 2878F-B01
• Responsible Party:
• Sharp Electronics Corporation
• 100 Paragon Drive, Montvale, NJ 07645
• TEL: 1-800-BE-SHARP
• www.sharpusa.com

PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

• Do not attempt to operate this oven with the door open since open-door operation can result in harmful exposure to microwave energy. It is important not to defeat or tamper with the safety interlocks.
• Do not place any object between the oven front face and the door or allow soil or cleaner residue to accumulate on sealing surfaces.
• Do not operate the oven if it is damaged. It is particularly important that the oven door close properly and that there is no damage to the: (1) door (bent), (2) hinges and latches (broken or loosened), (3) door seals and sealing surfaces.
• The oven should not be adjusted or repaired by anyone except properly qualified service personnel.

FCC

IMPORTANT REGULATORY INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and
• this device must accept any interference received, including interference that may cause undesired operation

Any changes or modifications to the appliance not expressly approved by the party responsible for compliance could void the user’s authority to operate the appliance. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal- lation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer- ence will not occur in a particular installation. If this equipment does cause harmful interterence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>