PROFLO PFFSR5931WH, PFFSOS25932WH 2 Piece Freestanding Acrylic Tub Instruction Manual
- June 9, 2024
- PROFLO
Table of Contents
2-Piece Freestanding Acrylic Tub
Installation Instructions
PFFSR5931WH/PFFSOS25932WH
PFFSR5931WH, PFFSOS25932WH 2 Piece Freestanding Acrylic Tub
Thank you for selecting PROFLO Products. To ensure this product is installed properly, please read these instructions carefully before you begin. Certain products may require professional help to ensure your installation conforms to local codes.
Important
- Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. All bath units are factory tested for proper operation prior to shipping.
- Inspect the shell and bathtub components. Should inspection reveal any damage or defect in the finish or visible damage to any components, do not instal the bathtub. Damage or defect to the finish claimed after the bathtub is installed is excluded from the warranty.
- Inspect the tub components for loose fittings.
- Prior to installation, the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage or mishandling.
- It is the responsibility of the installer to thoroughly test the tub prior to completing installation. Place the tub on a level surface, ensure drain is sealed and fill the bathtub with water to the bottom of the overflow. Allow water to sit in tub for at least 15 minutes as a static test. Visually inspect all joints for leaks. DO NOT install tub if any leaks are detected.
You May Need
| | | | Also
Drop Cloth
---|---|---|---|---
Important Safety Instructions
Save this manual: retain for consumer’s use. Read these instructions
completely before installing the product. For product or installation
questions please call customer service at
1-800-221-3379.
You must follow all instructions in this manual: failure to do so will result
in your assumption of liability and will void warranty and can result in
product damage or personal injury. Failure to use a suitable setting compound
will void the warranty.
This product is designed to be installed by a licensed tradesman. Licensed
plumbers and electricians should be employed to ensure proper installation.
Installers assume all liability for the correct installation procedures. Only
accessories authorized by the manufacturer should be used with this product.
This product is designed for residential use
and use by healthy individuals.
WARNING
When using this product, basic precautions should always be followed. Read and
follow all instructions pertaining to risk of fire, electric shock, or injury.
Installer: leave this manual for homeowner.
Homeowner: read this manual and keep for future reference.
Risk of personal injury. Do not permit children to use this unit without adult
supervision.
Risk of hyperthermia and possible drowning. People using medications and/or
having adverse medical history should consult a physician before using this
product.
Risk of personal injury. Do not overfill unit before entering. Entering tub
when filled more than 2/3 can cause overflow and slippery conditons. Exercise
caution when entering and exiting.
No food or alcoholic beverages. Use of your bathtub immediately after meals is
not recommended. Avoid alcohol consumption before or during bathing. Alcoholic
beverages can cause drowsiness or hyperthermia resulting in loss of
consciousness or even drowning.
If you are or think you may be pregnant, consult your physician before using
the bathtub.
Never drop or insert any object into any opening.
Use this unit only for its intended use as described in this manual. Do not
use any attachments not recommended by PROFLO.
This equipment is intended for indoor use only.
Installer/owner bears all responsibility to comply with all state and local
codes when installing this product.
Before Beginning
- Carefully read the instructions before beginning the installation.
- To protect the unit during installation, we recommend that you lay a piece of cardboard underneath the bathtub.
- Place the unit in the bathroom before you start working. If the unit is covered with a polyethylene protective film, do not remove it until the installation is complete for maximum protection. However, remove film where two surfaces will be in permanent contact.
- It is strongly recommended that this installation be performed by a professional plumber or contractor.
- A minimum of two people are needed to perform this installation.
- The bathtub is designed for a freestanding installation only.
- Provide adequate floor support.
DO NOT SIT ON THE LEDGE OF THE BATHTUB
That might cause serious injury. PROFLO is not responsible for defects and/or
problems incurred under these circumstances.
Parts Illustration
| No. | Part | QTY |
|---|---|---|
| 1 | Tub/Inner Shell | 1 |
| 2 | Skirt/Outer Shell | 1 |
| 3 | Overflow | 1 |
| 4 | Toe Tap Drain | 1 |
| 5 | Hex Locknut | 8 |
| 6 | Adjustable Feet | 4 |
| 7 | Adjustable Feet Cap | 4 |
| 8 | Adjustable Thread | 4 |
Installation Procedure
- Determine the final location of the tub. The tub will sit on top of the finished floor, but the drain may sit below the finished floor. Tubs installed on a slab foundation may require additional effort to gain clearance for installation. Ensure there is clearance for supply lines if installing a deck mounted faucet. Recommended to use SH651 rough in drain kit.
- Dry fit tub in final location on the floor. Once the unit is in position, ensure it is level to ensure proper drainage. If the tub is not level, the feet on the bottom of the tub can be adjusted. Adjust the feet so they extend 1/4″ (6mm) past the base of the tub. The bathtub’s weight should be supported by the feet, not the skirt/outer shell of the tub.
- Ensure the location is structurally sound and can carry the weight of the tub when filled with water. Refer to the specification sheet for water capacity and weights.
- Apply silicone to the bottom side of the outer shell/ skirt. Set bathtub in place.
Optional: Installing deck-mounted filler
- Flexible supply lines are required with length to allow for making the connection to the faucet above the rim of the tub.
- Locate the desired placement of the faucet on the tub deck and ensure faucet will fit without any overhang or interference below the deck of the tub.
- Mark location for faucet holes and drill with hole saw from the finfshed side of the deck.
- To provide access for making final connections, temporarily position 2x4s on to top of the skirt and place the bathtub in place on top of the 2x4s.
- Install faucet per the faucet manufacturer’s installation instructions and make connections to water supply.
Dimensions
| Models/Capacity | A | B | C | D | E | E | G | H | I | J | K | L |
|---|
PFFSOS25932WH
58 gallon| 59″| 51-5/8″| 40″| 29-1/8″| 23″| 23″| 28-1/2″| 3″| 5-7/8″| 32″|
3-1/2″| 43-1/8″
1500mm| 1310mm| 1015mm| 740mm| 585mm| 585mm| 723mm| 75mm| 150mm| 813mm| 90mm|
1094mm
PFFSOS25932WH| 59″| 56-1/2″| 43-1/4″| 23″| 23″| 23″| 26-1/8″| 2-3/8″| 4-7/8″|
27″| 3-1/4″| 53″
1500mm| 1436mm| 1100mm| 585mm| 585mm| 585mm| 664mm| 75mm| 127mm| 690mm| 83mm|
1350mm
Drain Installation
NOTE: Make sure drain connection is tight and completely installed.
- Install 1-1/2″ rubber slip gasket over the drain waster vent.
- Cut tail piece to desired length (will vary for each installation).
- Slide tail piece nut over tail piece towards flanged end.
- Connect tail piece assembly to waste vent.
- Place flange washer on top of tail piece.
- Ensure the slot in the drain is lined up to the overflow channel in the tub. Clear silicone is recommended for use under the flange on the drain body, as plumber’s putty can dry and crack, leaving opportunity for leaking. Plumber’s putty may also discolor the tub or drain finish over time.
- If desired, apply a thin, continuous bead of silicone around the base of the skirt and the floor.
- Clean all debris from tub. Do not use wire brushes or anything abrasive or metal on bathtub surfaces.
- Fill tub and test for leaks.
Care And Cleaning
DO NOT use powdered cleaners unless cleaner is fully dissolved in water. Fill
the tub 1/4 of the way with hot water and add 2-3 teaspoons of low foaming
detergent such as dish washing machine detergent.
DO NOT use full strength bleach or ammonia cleaning solutions. Chemically
active cleaning solution can damage the bath surface.
DO NOT USE ABRASIVE CLEANERS as they will scratch and dull the surface of the
acrylic and void the consumer warranty.
DO NOT USE METAL SCRAPERS, WIRE BRUSHES OR OTHER HARSH ABRASIVE TOOLS.
Usually a mild detergent will remove construction debris. More stubborn debris
may be removed with denatured alcohol or Clorox Soft Scrub ® cleaner.
Light scratches and dulled areas may be restored to original luster by rubbing
with an automotive type cleaning compound such as DuPont White Polishing
Compound ® .
Note: Apply white automotive polishing with a clean rag to restore dull or
scratched units. Rub scratches and dull areas vigorously. Wipe off residue.
Follow with a coat of white automotive paste wax.
DO NOT wax areas where you walk or stand.
For crack and major surface damage, call customer service at
1-800-221-3379 for repair
recommendations.
Warranty
What is covered
PROFLO warrants to the original consumer purchaser that its bathtub and
bathing system (except as explained under paragraph 3, below) shall be free
from defects in aterial and workmanship under normal use and service for five
(5) years. If the bathtub and bathing system is used in industrial, commercial
or business applications, the preceding sentence does not apply, but rather
for all industrial, commercial or business applications, the warranty shall be
a one (1) year limited warranty from the date of purchase with all other
terms and exclusions of the warranty applicable.
PROFLO’S obligations
PROFLO’s obligations under the warranty set forth in paragraph 1 above shall
be to replace free of charge any PROFLO bathtub and bathing system which is
defective as stated above, or at PROFLO’s option, to either refund the
purchase price or repair the bathtub and bathing system. The warranty set
forth in paragraph 1 is in lieu of any other warranty, expressed or implied,
and shall run to the original purchaser only.
What is not covered
The warranty set forth in paragraph 1 does not cover and PROFLO is not liable
for, (i) installation, (ii) any labor charges or (iii) products which have
been damaged as a result of any accident, misuse, abuse, neglect, improper
installation or maintenance, the use of abrasive or organic solvent cleaners,
modification, failure to use the bathtub and bathing system in accordance with
instructions provided by PROFLO or use of parts other than PROFLO parts. How
to obtain warranty service the purchaser should contact their local ferguson
location, installing contractor or builder from whom the product was purchased
or call PROFLO customer service at
1-800-221-3379. Disclaimer of
consequential or incidental damages and other warranties PROFLO shall not be
liable for personal injury or property damage or any consequential, punitive
or incidental damages. Except as stated in paragraph 1, PROFLO disclaims all
expressed or implied warranties, including those of merchantability and
fithness for a particular purpose. PROFLO’s liability, if any, shall not exceed
the replacement value of the defective bathtub and bathing system. Some states
do not allow the exclusion or limitation of incidental or consequential
damages or limitations on how long an implied warranty lasts, so the above
limitations may not apply to you. This warranty gives you soecific legal rights
and you may also have other rights, which vary from state to state.
Please pay attention to following when maintaining your bathtub. Failing to do so will void the warranty:
- Improper care & cleaning
- The use of bath oils and bath salts will void the warranty
- The use of abrasive cleaners, metal scrapers, wire brushes or other harsh abrasive tools
- Inappropriate installation and maintenance will void the warranty. Contact PROFLO customer service at 1-800-221-3379 or email support@proflo.com
©2022 Ferguson Enterprises, LLC 0222 3690141
FERGUSON.COM/PROFLO