AESCULAP Exacta GT416 / Isis GT421 Instruction Manual
- June 9, 2024
- Aesculap
Table of Contents
AESCULAP Exacta GT416 / Isis GT421
OVERVIEW
Thank you
for choosing the Exacta/Isis, the professional trimmer from Aesculap.
It utilises state-of-the-art technology, is innovative and has a strong
emphasis on design. When developing the trimmer, the requirements for a
professional trimmer used in a hair salon were taken into consideration. The
trimmer is specifically designed for precision cutting of hair contours. In
addition to optimum cutting performance, the Exac-ta/Isis provides
- low weight
- a low-vibration and quiet motor
- long battery life thanks to Li-ion battery
- 4-stage cutting length adjustment with comb attachment
- cable storage
We wish you every success in the use of our shearing machine. Best regards,
Aesculap Schermaschinen GmbH
Names of parts
- Charging indicator
- Charging unit
- Charging contacts
- On/Off switch
- Blade set
- Blade set fixing screw
- Charging contacts of the appliance
- Mains adapter
- Cable storage compartment
- Power supply adapter
- Comb attachment
- Oil bottle
- Cleaning brush
- Allen key (in base of charging unit)
Safety
Please read the instructions carefully, especially the chapter on “Safety”,
before using the trimmer. This will protect you from possible dangers and the
appliance from damage due to incorrect operation.
Keep these instructions in a safe place for future refer-ence. If you pass on
the appliance to someone else, be sure to hand over these instructions as
well.
Explanation of warnings
In these instructions you will find the following warn-ings:
DANGER: High risk. Failure to observe the warning can cause serious
injury.
WARNING: Medium risk. Failure to observe the warning may cause damage to
property.
NOTE: Low risk. Points that you should observe when using or handling the
appliance.
Intended use
- The shearing machine is used for shearing small animals.
- The appliance is intended for trimming purposes only.
- The appliance is designed for indoor use only. Do not use outdoors (garden, patio etc.).
- The appliance was developed for professional use in grooming-salons and veterenary practice. Provided the safety information is observed, it can also be used in the home.
Important information about dangers
Danger of electric shock: The appliance must never be used or charged in
the bath, shower, over a full wash basin or other water container, or with wet
hands. Keep the device, the charging station and the power cord free of
moisture, water and other liquids and never oper-ate it with wet hands.
- Do not immerse the device, the charging station or the power cord under water or rinse under flowing water.
- If the appliance has fallen into water, it must not be used after that.
- Additional protection is afforded by installing a residual current device with a rated tripping current of less than 30 mA in your home electrical system. We recommend you get an electrician to install a residual current protection system to protect the circuits..
WARNING: The shaver head can become hot after extended use!
NOTE: The Clipper may be operated only with a power supply according to the specifications on the rating plate.
General safety information
Never use the appliance if:
- the appliance, the charging station or the power cord are damaged.
- the blade set is damaged or breaking up, as this could cause injuries to the skin.
- the appliance has fallen or been dropped, shows signs of damage or is not functioning properly.
- the appliance is so badly damaged that electrical parts are exposed.
In all such cases, disconnect from the mains immediately and inform Technical Customer Service.
- Check whether the mains voltage agrees with the voltage specified on the rating plate.
- Only operate device with the original power supply.
If the device has the marking any T10 model power supply can be used.
Shearing machines for animals may only be used by trained personnel.
- Keep the appliance out of reach of children.
- Also keep the packaging material, e.g. plastic film, away from children.
- Lay the power cord so that no one trips over or steps on it!
- Protect the power cord from damage. Never pull on the power cord. Grasp the power plug when you pull it from the socket. Keep the cord away from hot sur-faces.
- Regularly inspect the power cord for damage.
- Operate and charge the device only between 0°C–40°C.
- To avoid risks, repairs must only be carried out by au-thorised Aesculap Customer Service Centres. This also applies to replacing the rechargeable battery.
- The blade set must not be dismantled.
- The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, un-less they have been given supervision or instruction..
- Children being supervised not to play with the appli-ance.
DANGER: To ensure proper functioning of the appliance, the blade set must
be cleaned regularly and oiled in the appropriate places (see “Cleaning and
care” on page 16).
The appliance must be switched off whenever:
- you put it down, e.g. to recharge it or stop cutting hair for a short period.
- you fit or remove the comb attachment.
- you want to clean or oil the appliance.
- Use the trimmer only in combination with the original Aesculap accessories (charging unit, comb attach-ment etc.).
- Never attempt to remove dust or foreign bodies from inside the appliance with pointed objects (e.g. with the tail of a comb).
NOTE: The safety of Aesculap electrical appliances is in line with the
recognised state of the art and the German Equipment Safety Act.
Light-emitting devices such as LEDs or infrared light do not exceed Laser
class 1 of IEC 825-1.
Given the present state of the art, components of electrical appliances are subject to a certain degree of wear over time. To ensure perfect functioning and safety, we therefore recommend regular inspection by the Technical Customer Service of Aesculap Schermaschinen GmbH.
Service Addresses
ADDRESS: Albert Kerbl GmbH Felizenzell 9 84428 Buchbach / Germany
Phone: +49 8086 933-100
Fax: +49 8086 933-500
E-Mail: info@kerbl.com
www.kerbl.com
Further service addresses you can demand from the men-tioned above address.
Preparation
Charging
The device should be charged for 2 hours before first use.
Before plugging in the trimmer, make sure that the mains voltage agrees with
the voltage specified on the rating plate.
It is not possible to “overcharge” the appliance.
NOTE
If you also use the predecessor model type HS61 in addition to the new type
HS62 shearing machine, you can charge the device in the old charging station
(charge time 90 minutes) and/or charge the old device type HS61 in the new
charging station (charging time 60 minutes).
The type HS60 shearing machine can also be charged in the type HS62 charging station. However, it is not possible to charge a type HS62 in the charging station for the type HS60.
- Insert the mains adapter 8 in a power socket.
- Place the charging unit 2 on a flat surface.
Place the device in the charging station. It positions itself and begins to charge. The green charge indica-tor 1 blinks when charging current is flowing. Ensure that the on/off switch 4 is set to 0 during charging. The battery is completely charged as soon as the green charge indicator 1 lights up steadily.
Storing power cord
If you do not need the full length of the cord, a portion of the power cord can be stored in the cable storage 9.
- Pull out the mains plug.
- Turn the charging unit upside down.
- Wind the excess cable round the holder in the base, then run the cable through the small recess in the housing to the outside.
Changing power supply adapter
The device is delivered w ith a power supply adapter 10. Risk from electric
shock!
- Use only the original power supply adapter 10.
- Remove the power supply device 8 from the socket before changing the power supply adapter 10.
- Make certain that the power supply device 8 cannot be reinserted during cleaning.
WARNING: Damage to power adapter from incorrect use!
- Be sure not to bend the small pins on the power supply device 8.
- Push the release button in the direction of the arrow while withdrawing the installed power supply adapter 10.
- Insert the required power supply adapter 10 into the power sup-ply device 8. Ensure that the release button is on top and locks into place.
Operation
Switching On and Off
- To switch the appliance on, slide the On/Off switch 4 forward.
- To switch the appliance off, slide the On/Off switch to position 0.
Comb attachment
-
Switch off the trimmer and slide the comb attachment onto the blade set until it snaps into place.
You can now start trimming hair with the trimmer in the usual way. -
The comb attachment can be ad-justed to 4 different cutting lengths (approx. 3 to 6 mm). To do so, push it to the required po-sition on the blade set.
The further you push the comb attachment onto the blade set, the shorter the cutting length.
Cleaning and care
To ensure proper functioning and full performance from your trimmer, clean and oil the appliance regularly. Cleaning the blade set
WARNING: Damage to the clipper head caused by its removal!
- Never remove the clipper head. Once removed it cannot be reattached.
If used regularly, the blade set 5 should be thoroughly cleaned once a day.
- Switch the appliance off.
- Remove the comb attachment if fitted.
- Use the cleaning brush 12 to remove any hairs.
Oiling the blade set
To maintain the high-quality cutting performance of the blade set as long as
possible, it must be oiled regularly –every 10 minutes.
- Remove the comb attachment if fitted.
- Lubricate the areas where there is contact between the upper and lower parts of the blade set (see illustration).
Replacing the blade set
The blade set is subject to wear. Even if you look after the appliance
properly, the cutting performance will deteri-orate. Replace the blade set
when it is worn. The blade set can be ordered separately as a spare part from
Aesculap Customer Service (see addresses at the end of these instructions).
WARNING: Damage to casing when screwing on clipper head!
- Do not over tighten the screw.
- Make sure the On/Off switch 4 is in the 0 position.
- Remove the Allen key 13 from the base of the charging unit and use it to loosen the blade set screw 6.
- Loosen the screw fully and re-move it.
- Push the blade set upwards with your thumb.
- Push the new blade set on until it snaps into place and secure it using the screw.
While the blade set is removed, you can use the cleaning brush to remove residual hair from inside the appliance.
Cleaning the appliance
- Clean your appliance occasionally with a damp cloth, then wipe it dry.
Cleaning the charging contacts
If the charging contacts 7 on the appliance or the charg-ing contacts 3 on the
charging unit are dirty, charging may not be possible or may be interrupted.
- Clean the contacts using a cloth or wad of cotton wool soaked in alcohol or spirit.
Clean the contacts using a cloth or wad of cotton wool soaked in alcohol or spirit.
- Make sure you do not leave the appliance switched on when putting it aside if the battery is run down.
- Make sure the appliance is switched off (On/ Off switch to 0) when you place it in the charging unit.
What should I do if
The appliance will not switch on?
- Is the battery low? Plug in the mains adapter for the charging unit and charge the trimmer.
- Is the blade set dry? The blade set must be oiled. Pro-ceed as described on page 17.
The blade set “sticks”?
- The blade set must be oiled. Proceed as described on page 17.
The charging indicator does not light up when charging?
- Clean the charging contacts.
- The appliance may not be positioned correctly in the charging unit. Position it correctly.
- Is the charging unit properly connected?
The appliance switches itself off?
- The battery is low. Charge the trimmer.
Does the battery no longer charge?
- Check whether the charging stand for the HS60 shearing machine is being used; see ID plate on charging stand. This is incompatible with the HS62 shearing machine.
- If not, send the machine to the Aesculap repair ser- vice.
Disposal
This electrotechnical device has a permanently installed battery.
The product contains electronic components and/or batteries. Do not dispose of the device in household trash; instead, deliver it for recycling to a community collection point.
Technical data
- Product Exacta/Isis
- Mains adapter
- Input voltage 100-240 V ~ 50/60 Hz
- Capacity 600 mAh
- Volume < 60 dB(A)
- Total vibration level ah < 2.5 m/s²
- Attachment 1 comb attachment
- Dimensions 140 x 30 x 36 mm
- Weight 115 g
Subject to technical change without notice
United Kingdom
ADDRESS: Kerbl UK Ltd. 8 Lands End Way Oakham, Rutland LE15 6RF UK
www.kerbl.co.uk
Phone: 0044 01572 722558
Two-year guarantee
Dear Customer,
Thank you for choosing a product from our company.
For decades, the name Aesculap has stood for proven quality and first-class
service. We are known to provide innovative, high-performance products for our
custom-ers. Aesculap manufactures high-quality devices, using high-quality
materials and careful manufacturing pro-cesses. We would like to point out to
you that we are not liable for defects in our products, if these are caused by
improper use, normal wear or are caused by the product being improperly used
or if inappropriate or not properly functioning third-party products are used.
Defects that do not affect or only negligibly affect the value or function of
the product are also excluded from our warranty.
If we are liable under our warranty, we reserve the right to repair or replace
the product.
Service Addresses Albert Kerbl GmbH Felizenzell 9 84428 Buchbach /
Germany
Phone: +49 8086 933-100
Fax: +49 8086 933-500
E-Mail: info@kerbl.com
www.kerbl.com
Further service addresses you can demand from the men-tioned above address.
Aesculap Schermaschinen GmbH Fröhliche-Mann-Straße 15 98528 Suhl Germany
Phone: +49 3681 49820
Fax: +49 3681 498234
E-Mail: info@aesculap-schermaschinen.de
www.aesculap-schermaschinen.de
References
- schermaschinen.de
- Start - Aesculap
- Home - Kerbl UK Ltd
- Everything around animal breeding, husbandry and agricultural supplies - Albert Kerbl GmbH
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>