ZEVNI A04626 Gold Vanity Light Instruction Manual

June 9, 2024
ZEVNI

ZEVNI A04626 Gold Vanity Light

ZEVNI-A04626-Gold-Vanity-Light-product

Item Number: A04626

WARNING
(To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.
  2. Please read the instruction carefully and save it as you may need it at a later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
    • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
    • Place the wall switch in the “OFF” position.
  4. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
  6. Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
  7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
  8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

ZEVNI-A04626-Gold-Vanity-Light-fig-1

TOOLS REQUIRED (NOT INCLUDED):

Before starting assembly and installation please prepare the needed tools as below pictureZEVNI-A04626-Gold-Vanity-Light-fig-2

PARTS TYPE & QTY INCLUDING

  • Green ground screw (1)
  • (D) Mounting plate (1)
  • (E) Screw (4)
  • (F) Backplate (1)
  • (G) Socket (1)
  • (H) Glass shade (1)
  • (I) Iron frame (1)
  • (J) Glass holder (1)
  • (K) Butterfly nut (1)

ACCESSORIES & QTY ENCLOSED:

  • (A) Plastic wire connector (3)
  • (C) Mounting screw (2)ZEVNI-A04626-Gold-Vanity-Light-fig-3

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

  2. Turn off power
    Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

    • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
    • Place the wall switch in the “OFF” position.
  3. Make installationZEVNI-A04626-Gold-Vanity-Light-fig-4

  • Step A1 » Unscrew screws (E) from back plate (F) then gently remove mounting plate (D). Then set them aside for later installation.
  • Step A2 » Carefully pass the supply wires from the outlet box through the mounting plate (D). Secure the mounting plate (D) to the outlet box with mounting screws (C).
  • Step A3 »
1. Install the bulb (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
2. Remove butterfly nut (K) and the iron washer from the glass holder (J).
3. Carefully place glass shade (H) on the socket (G).
4. Place glass holder (J) on glass shade (H), insert it into back plate (F) and into the previously removed iron washer, then secure them by tightening butterfly nut (K) onto glass holder (J).
  • Step A4 » Make wire connections Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.ZEVNI-A04626-Gold-Vanity-Light-fig-5

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

  • Step A5 » Position back plate (F) and mounting plate (D) in place, carefully thread screws (E) through the holes in back plate (F) and mounting plate (D). Secure them by tightening screws (E).

Check everything is installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ZEVNI User Manuals

Related Manuals