Style SELECTIONS SGY-GHR2 Retractable Wall Mount Hose Reel User Manual

ITEM #4979243
RETRACTABLE WALL MOUNT HOSE REEL
MODEL #SGY-GHR2
User Manual

SGY-GHR2 Retractable Wall Mount Hose Reel

ATTACH YOUR RECEIPT HERE
StyleSELECTIONS® and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.
Serial Number ——
Purchase Date ——
Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-888-8225, 8:00 a.m. – 8:00 p.m., EST, Monday – Sunday. You could also contact us at [email protected].
SC22022

PRODUCT SPECIFICATIONS

Hose Diameter
Inlet Hose Length
Outlet Hose Length
Maximum Operating Pressure
Weight| 7/16 x 5/8 in. (accepts 1/2″ fitting)
6 ft (2 m)
100 ft (30 m)
8 bar
23.1 lbs.

PACKAGE CONTENTS

HARDWARE CONTENTS

**** SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product, please call customer service at 1-877-888-8225, 8:00 a.m. – 8:00 p.m., EST, Monday – Sunday.
You could also contact us at [email protected].
WARNING

• Improper assembling or operation of this product could result in serious injury or property damage. Read and understand all assembly and operation instructions.
• Connect only to water source with pressure at or below 8 bar.
• Protect your eyes by wearing safety glasses or a face shield when mounting and using this product.
• Keep loose clothing, hair, and jewelry away from moving parts of hose reel.
• Make sure that the product is firmly mounted before pressurizing.
• Rapidly retracting hose could cause injury and property damage. Maintain control of hose as it retracts.
• Keep hose away from sharp edges. Check hose for wear before each use.
• Release water pressure when not in use.
• Product contains charged spring. Do not disassemble housing.

PREPARATION
Before assembling the product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

ASSEMBLY INSTRUCTIONS

This product can be mounted in many different ways. It is important to select your mounting location carefully. Consider mounting to surfaces.

1. Near your water source. This product includes 100 ft (30 m) of outlet hose. Make sure it can reach your garden.
2. Near your water supply. This product includes 6 ft (2 m) of inlet hose. Make sure it can reach your water supply.
3. Out of direct sunlight.
4. Strong enough to support the loads shown to the right (per screw). If unsure, contact a professional installer.
5. Refer to the installation options below for more detail.

WARNING: If not properly installed, there is a risk of falling. Make sure your installation can support the loads above.
CAUTION: When using power tools, please wear eye protection.
WARNING: Ensure there are no live electrical wires or plumbing in the wall at the location you are drilling.
MOUNT TO STUD AND DRYWALL
Estimated Assembly Time: 20 minutes
Hardware Used![Style SELECTIONS SGY GHR2 Retractable Wall Mount Hose Reel

• Hardware Used](https://manuals.plus/wp-content/uploads/2023/01/Style- SELECTIONS-SGY-GHR2-Retractable-Wall-Mount-Hose-Reel-Hardware-Used.jpg) Tools Required for assembly and installation (not included):

  • Stud-finder
  • Level
  • Drill & 3/8″ (10 mm) Drill Bit, 7/32″
  • Hammer or Mallet
  • 10 mm Wrench or Socket
  • Tape Measure
  • Pen or Pencil (5.5 mm) Drill Bit
  • Adjustable Wrench

1. Using stud-finder, locate stud and mark the location.
2. Using mounting bracket (F) from the unit, hold the bracket over the location you marked for the stud. Make sure both holes on either the left side or right side match up to the center of the stud.
3. Using the level make sure the bracket is level and then using a pencil or pen mark the four (4) hole locations.
4. Using a 7/32″ (5.5 mm) drill bit drill the 2 holes you marked over the stud.
5. Using a 3/8″ (10 mm) drill the other 2 holes you marked.
6. Tap a plastic anchor into each hole you drilled with the 3/8″ (10 mm) drill bit with a hammer or mallet.
7. Fasten the mount bracket (F) with four screws (AA) and washers (BB) to stud and drywall.
8. Hang the hose reel (A) on the mount bracket (F), and secure it by inserting the mount pin (E).
9. Connect with inlet hose (D) end with the water source.

MOUNTING TO A MASONRY WALL
Estimated Assembly Time: 20 minutes
Tools Required for assembly and installation (not included):

• Level
• Drill & 3/8″ (10 mm) Masonry Drill Bit
• Hammer or Mallet
• 9/16″ (14 mm) Wrench
• Tape Measure
• Pen or Pencil
• Adjustable Wrench

MOUNTING TO A MASONRY WALL
Estimated Assembly Time: 20 minutes
Tools Required for assembly and installation (not included):

• Level
• Drill & 3/8″ (10 mm) Masonry Drill Bit
• Hammer or Mallet
• 9/16″ (14 mm) Wrench
• Tape Measure
• Pen or Pencil
• Adjustable Wrench

WARNING

1. Using mounting bracket (F) from the unit, hold the bracket over the location you want to mount the hose reel.
2. Using the level make sure the bracket is level and then using a pencil or pen mark the four (4) hole locations.
3. Make sure the nut is at the top of the thread on the masonry anchor. Insert a masonry anchor into each hole and gently tap the top of the anchor until the anchor is fully seated in the wall.
4. Remove the nut, lock washer, and flat washer from the anchor. Mount the mounting bracket (F) onto the masonry anchors, then assemble the flat washers, lock washers and nuts. Tighten all nuts until the masonry anchors are secure.
5. Hang the hose reel (A) on the mount bracket (F), and secure it by inserting the mount pin (E).
6. Connect with inlet hose (D) end with the water source.

Hardware Used

OPERATING INSTRUCTIONS

WARNING: Always hold the hose reel until it completely retracts into the hose reel.
WARNING: The yellow tape marks the end of hose length.
WARNING: Release pressure when not in use.
CAUTION: Do not release the hose allowing to rewind on its own.

1. Pull the hose out to the desired length. The hose will automatically lock in position.
2. To unlock and retract, give the hose a short pull. Walk the hose back to the hose reel. If you pull the hose longer than 4″ (10 cm) you may re-lock the hose.
3. To avoid injury and damage, always hold the hose while it is retracting. This hose reel has a controlled return function.
4. If the hose becomes tangled and will not retract – slowly pull out the hose past the tangled section and then allow the hose to slowly retract while guiding the hose back into the hose reel. Always ensure the hose is clean and not twisted.

ADJUSTING THE STOP-BALL
The stop-ball location can be adjusted to ensure the hose is always within reach.
Recommended tools
• No tool is needed.

1. Pull out the hoes to the desired length, ensuring the hose reel is locked (will not rewind).
2. Open the latch on the stop ball (B) and move it to the desired location.
3. Re-latch the stop ball (B).

CAUTION: always make sure the hose reel is locked before removing the stop ball, and make sure the stop ball is securely fastened before unlocking the reel.

CARE AND MAINTENANCE

While your product has been made with high quality materials, degradation can occur over time. Inspect the hose and housing periodically. If cracking or blisters are visible, discontinue use.
WARNING: PRODUCT CONTAINS CHARGED SPRING. DO NOT DISASSEMBLE HOUSING.

1. Always keep the hose clean.
2. If the hose becomes dirty, clean it with a damp cloth while retracting.
3. DO NOT twist the hose while in use.
4. Mount the hose reel in a sheltered area to assist and protect the performance of the hose and the reel.
5. DO NOT allow the hose to contact any corrosive chemicals or fluids.
6. Always retract the hose when not in use.

TROUBLESHOOTING

If you have any questions regarding the product, please call customer service at 1-877-888-8225, 8:00 a.m. – 8:00 p.m., EST, Monday – Sunday. You could also contact us at [email protected].

adjusted in the best angle/position.
2. Roller bracket is damaged.| 1. Adjust roller bracket in the best angle/position.
2. Replace roller bracket.
The hose will not retract smoothly.| 1. Roller bracket is not adjusted in the best angle/position.
2. Roller bracket is damaged.| 1. Adjust roller bracket in the best angle/position.
2. Replace roller bracket.

WARRANTY
This water hose reel is warranted by the manufacturer to the original purchaser from the original purchase date for two (2) years subject to the warranty coverage described herein.
This water hose reel is warranted to the original user to be free from defects in material and workmanship. If you believe that a water hose reel is defective, return the water hose reel, with proper proof of purchase to the point of purchase. If it is determined that the water hose reel is defective and covered by this warranty, the distributor will replace the water hose reel or refund the purchase price.
This warranty is void if: defects in materials or workmanship or damages result from repairs or alterations which have been made or attempted by others or the unauthorized use of nonconforming parts; the damage is due to normal wear, damage is due to abuse (including overloading of the water hose reel beyond capacity), improper  maintenance, neglect or accident; or the damage is due to the use of the water hose reel after partial failure or use with improper accessories or unauthorized repair or alteration.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For warranty questions, call our customer service department at 1-877-888-8225, 8:00 a.m. – 8:00 p.m., EST, Monday – Sunday. You could also contact us at [email protected].

Printed in China

Documents / Resources

| Style SELECTIONS SGY-GHR2 Retractable Wall Mount Hose Reel [pdf] User Manual
SGY-GHR2 Retractable Wall Mount Hose Reel, SGY-GHR2, Retractable Wall Mount Hose Reel, Wall Mount Hose Reel, Mount Hose Reel, Hose Reel, Reel
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>