Turtle Beach Stealth 600 Gen 2 MAX Headset User Guide
- June 9, 2024
- TURTLE BEACH
Table of Contents
Turtle Beach Stealth 600 Gen 2 MAX Headset
IMPORTANT
READ B E FORE USING
IMPORTANT
PLEASE MAKE SURE YOUR HEADSET IS UPDATED WITH THE LATEST FIRMWARE.
- Connect to the Turtle Beach Audio Hub for Windows or Mac® to update firmware .
- turtlebeach.com/audiohub
CONTENTS
HEADSET CONTROLS
Microphone Mute
Flip up mic to mute. There is an audible tone when the mic is muted or
unmuted.Use Superhuman Hearing· Mode to pinpoint quiet audio cues like enemy
footsteps and weapon reloads. During gameplay, you can activate and deactivate
Superhuman Hearing'” by pressing the POWER button once, quickly.
EQ PRESETS
- Signature Sound
- Bass Boost
- Bass + Treble Boost
- Vocal Boost
SETUP FOR XBOX
SURROUND SOUND FOR XBOX (ONLY AVAILABLE ON XBOX)
- Go to Slttinp > Gtnenl ► Volume Ii Audio Output
- Set Headset Format to Windows Sonic for Headphones
For updated setup instructions visit: turtlebeach.com/sonic
CHANGING
The Stealth” 600 Gen 2 MAX gives you 48+ hours of rechargeable battery life.
Make sure to charge it regularly before storing.
Headset Storage
Always charge your headset before storing it for any extended period of time
(greater than 3 months]. Never store the unit in temperatures above 113°
F/45°C.
USB TRANSMITTER COMPATIBILITY
- The USB-A transmitter is equipped with a switch that allows you to change compatibility modes.
*Nintendo Switch”‘ wireless compatibility is supported while in decked mode only. Chat is available for games that support in-game chat capabilities,
SETUP FOR USB MODE
LED BEHAVIORS
RE-PAIRING
- From OFF, press and hold the POWER button on the headset until the LED starts flashing rapidly.
- Insert the transmitter into the console.
- Press and hold the pin-hole button on the side of the transmitter until the LED starts flashing rapidly.
- After a few moments, the headset and transmitter LEDs will become solid, indicating a successful pairing.
Local Restrictions on Radio Usage
Caution: Due to the fact that the frequencies used by wireless devices may not yet be harmonized in all countries, these radio products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. Any deviation from the permissible power and frequency settings for the country of use is an infringement of national law and may be punished as such. To determine whether you are allowed to use your wireless network device in a specific country. please check to see if the radio type number that is printed on the identification label of your device is listed in the manufacturer’s OEM Regulatory Guidance document at the following http://www.turtlebeach.com/homologation or contact Turtle Beach directly. Federal Communications Commission (FCC) Compliance Notices This section includes the following FCC statements for the Stealth600X-MAX-RX & Stealth600X-MAX-TX:
- FCC ID: XGB-2362-RX & XGB-2362-TX
- RF Radiation Exposure & Hazard Warning
- Cla$:i B Interference Statement
- Non-Modification Statement
Class B Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC
FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: [1) This device may not cause harmful
interference, and [2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Radiation Exposure & Hazard Statement
To ensure compliance with FCC RF exposure requirements, this device must be
installed in a location such that the antenna of the device will be greater
than 2 cm [0.8 in.) from all persons. Using higher gain antennas and types of
antennas not covered under the FCC certification of this product is not
allowed. Installers of the radio and end users of the product must adhere to
the installation instructions provided in this manual. This transmitter must
not be co-located or operated in conjunction with any other antenna or
transmitter.
Non-Modification Statement
Use only the supplied internal antenna. Unauthorized antennas, modifications,
or attachments could damage the Stealth600X-MAX-RX & Stealth60OX-MAX-TX and
violate FCC regulations. Any changes or modifications not expressly approved
by the party responsible for compliance could void the user’s authority to
operate this equipment. Please contact Turtle Beach for a list of approved 2.4
GHz antennas. This product is compliant with the Consumer Product Safety
Improvement Act of 2008, Public Law 110-314 ([CPSIA)
Canadian 1CES Statements
IC:3879A-2362-RX & 3879A-2362-TX (Stealth600X-MAX-RX & Stealth 600%-MAX-TXJ
This device complies with ICES-003 and RSS-247 of Industry Canada. Operation
is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF Radiation Exposure & Hazard Statement
To ensure compliance with RSS-102 RF exposure requirements, this device must
be installed in a location such that the antenna of the device will be greater
than 2 cm l0.8 in.) away from all persons. Using higher gain antennas and
types of antennas not covered under the IC certification of this product is
not allowed. Installers of the radio and end users of the product must adhere
to the installation instructions provided in this manual. This transmitter
must not be CO-located or operated in conjunction with any other antenna or
transmitter.
To access the rating label:
- Remove the left ear pad by pulling the ear pad straight up using your thumb.
- Once you’ve released the cloth from the lip on top, pull the ear pad straight back and it should slip right off.
To replace the ear pad, follow the same process in reverse.
Not seeing what you’re looking for here?
Visit turtlebeach.com/support for the latest Tech Support information.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>