zafferano Sister Light Rechargeable Table Lamp Instruction Manual

: June 9, 2024
: zafferano

zafferano Sister Light Rechargeable Table Lamp

DIMENSION

LED DIMMER
3W • 250lm – 260lm – 270lm 2700K – 3150K – 4000K IP65 • CRI>90 • 5Vdc max 2A 13,2 x h 32,8 cm / Ø 5,2 x h 12,9 in

INCLUDED

NOT INCLUDED

This product contains a class F light source

Tips for use

This product is exclusively for lighting purposes and:

A) It must not be exposed to heavy mechanical loads or contamination;
B) It can be installed and used only after checking the state of the product; check that is not dirty and has not been damaged during storage;
C) Installation and maintenance must be carried out when the appliance is switched off;
D) Any alterations to the product, any tampering and any failure to comply with the instructions provided may make the appliance hazardous;
E) Products with IP65 protection are suitable for outdoor use;
F) All metal and plastic surfaces should be cleaned with a soft dry cloth;
G) The company Zafferano shall not be held liable for any damage caused due to its products being assembled in any manner that does not com-ply with the instructions provided.

Technical data

Power: 3 W
Volt: DC 5 V
Lumen lamp: 2700K 250 lm – 3150K 260 lm – 4000K 270 lm
LED: HONGLITRONIC 2835 /(8+42 pz) 3 STEP MAC ADAM
Lithium battery pack included (see section accessories included); for instructions about how to replace the battery pack, please consult the website: www.zafferanoitalia.com. We recommend using an original battery pack as a replacement.
Standard charge: 1A – 2A (max 2,5A)
Charge: 2A 5 h – 1A 10 h
Battery life: 100% 8 h – 60% 13 h – 30% 28 h – 6% 58 h
Class: III
Protection rating: IP65
CRI≥90
With reference to the UNI EN ISO 9227 standard, the lamp is guaranteed to resist exposure to neutral salt spray (NSS) for 1,500 hours.

Charger

You can use a charger with Standard-A USB to charge this product.
Dual USB port power charger NOT INCLUDED: INPUT 100-240 V AC – 50/60Hz; OUTPUT DC 5V – 2.1 A.
To correctly charge the lamp, we recommend that you: 1- Connect the USB cable to the adaptor; 2- Connect the USB cable to the lamp; 3- Put the plug into the electrical socket; 4- When fully charged, disconnect the plug from the electrical socket and remove the USB cable.
The lamp also operates properly when connected to the mains power supply.
We recommend using an optional charger and the original cable provided. Alternatively, use a certified cable and a 2A charger.

Manufacturer’s configuration

100% LUMINOSITY – 2700K – DIMMER ON – MECHANICAL FIXING

Important!

The support surface for the lamp must not exceed a 15° tilt or it will fall.
The battery is provided with the following protection functions: short circuit, over discharge, over charge, over current, over voltage.
To preserve the integrity of the battery, we recommend keeping the charge between minimum 20% and maximum 80%; if the lamp is not used for long periods, it is advisable to regularly charge/discharge the product.
Please refer to local laws for the proper disposal and recycling of the battery.

INSTRUCTIONS FOR USE

SWITCHING ON / DIMMING / SWITCHING OFF

Quick taps to

turn on
change the brightness
turn off the lamp
The steps are repeated in a cycle.

When you press and hold the touch button for two seconds, the lamp turns off, memorising the current dimmer setting and proposing it again the next time the lamp is turned on.

COLOR TEMPERATURE

When the lamp is turned off, press and hold the touch button:

after 5 seconds it turns on at 2700K
after 10 seconds it switches to 3150K
after 15 seconds it switches to 4000K The steps are repeated in a cycle.
If you release your touch during one of the steps, the lamp memorises the setting of the current step.

INDICATOR LEDS

PERMANENT RED LED
the battery charge is lower than 20%, charging is recommended.
When the charge is depleted (1%), the lamp does not switch on but emits three white flashes as an alert to charge
FLASHING RED LED charging in progress
PERMANENT BLUE LED
the battery is 100% charged, disconnection from the power charger is recommended

Reset settings > FACTORY RESET

Plug the lamp into the electric socket.
Place a finger on the touch sen-sor and keep it pressed down.
Unplug the lamp from the electric socket.
Remove your finger from the touch sensor.

Assembly instructions > MAGNETIC FIXING

Unscrew the top of the lamp from the threa-ded pin.
Unscrew the threaded pin.
Screw in the magnets and reposition the head on the stem.

NOT INCLUDED

zafferano Sister Light Rechargeable Table Lamp-fig12

INCLUDEN AND NOT INCLUDED ACCESSORIES

Charging cable with USB Type C input
- INPUT: 5Vdc max 1A
- OUTPUT: 5Vdc max 1A
Dual USB port power charger
- INPUT: 100-240V 50/60Hz
- OUTPUT: 5Vdc max 2A
Multi-socket USB charger (8xUSB)
- INPUT: AC100-240V 50/60Hz
- OUTPUT: 5Vdc max 8A
Replacement battery pack
Scan the QR code to see how to replace the exhausted batteries of your lamp.
Replacement LED board
Scan the QR code to see how to replace the LED board of your lamp.

zafferano Sister Light Rechargeable Table Lamp-fig13

LEGEND

User replaceable light source

zafferano Sister Light Rechargeable Table Lamp-fig16

User replaceable light source: Before replacing the light source of the device, view the video tutorial. In case of need, contact qualified personnel.

RECHARGEABLE BATTERY MAINTENANCE

All rechargeable batteries are subject to wear when used. The life of batteries, which can generally be re-charged 450 times, may be reduced by certain factors:

incorrect recharging mode (the lamp must be recharged when it is flat: about 10% of its remaining autonomy);
when left unused for a long time;
when left for a long time on a live recharging base even if the lamp is recharged;
when non-original accessories are used for rechar-ging;

Zafferano Srl – Viale dell’Industria 26 31055 Quinto di Treviso (TV) Italy www.zafferanoitalia.com

Light Department
+39 0422 470 507 lighting@zafferanoitalia.com