FIBRAIN GPON ONT 10-Gigabit and 1-Gigabit LAN Ports Installation Guide
- June 9, 2024
- FIBRAIN
Table of Contents
FIBRAIN GPON ONT 10-Gigabit and 1-Gigabit LAN Ports
Safety Guidance
Safety Check
Before installing the device, you must check the following items.
Electric Safety
- Ensure that there are no inflammable, conductive or moist objects around. Check whether the cables are aged and whether other electrical appliances are placed stably,
- Check whether the alternating or direct input Current is within the allowed range of the device, whether the polarity of the direct current is correct, and whether the earth line is properly connected.
Device Position
- Because the running electric device easily generates heat, please ensure to place the device in a well-ventilated environment,
- Avoid direct sunshine, and do not place the device on a PC case,
- Keep the device away from heat and water,
- Check whether power supply is available.
- The input voltage fiuctuation range must be smaller than 10%. The power plug should not share one socket with a hair drier, an iron or a refrigerator.
Safety Caution
- Read the quick installation guide carefully before using the device,
- Note all Cautions in the quick installation guide,
- Do not use any accessory that does not belong to the device without prior consent of the manufacture, as it may cause fire or product damage,
- Use the power adapter accompanied in the package,
- Do not place any object on the device,
- Keep the device dry, ventilated, rainproof, and clean,
- During lightning weather, unplug the power plug and all connection cables, to protect the device against lightning.
- Clean the device using a soft and dry cloth rather than liquid or atomizers.
- Power off the device before cleansing it,
- Power off the idle device, Keep the ventilation hole clean and prevent any object from dropping into the device through it. Otherwise, it may cause short circuit and further cause device damage or fire. Do not spray liquid on the surface of the device,
- Do not open the case of the device, especially during device power-on,
- Before plugging or unplugging the power, ensure that the power is off, thus avoiding surge,
- Be careful when unplugging the power, as the transformer may be very hot,
- Cover the optical interface with fiber interface cap when it is not in use. Avoid direct eye exposure to the laser emitted from the optical interface. Wear safety glasses if possible, to protect your eyes.
Caution
Please read the above safety guidance carefully before device use. Users
should assume responsibilities for any accidents due to incompliance with the
above instructionsS.
Overview
This chapter mainly describes functions and the structure of the HALNy HL- 4GMV2
Features and Function
- Fast rate. Support up to 1.25Gbps uplink and 2.5Gbps downlink data transmission rates,
- Strong maintainability. Provide various statuses of LED indicators, to help troubleshooting,
- Long transmission distance, up to 20 km.
Front, rear and side Panel
The description of the front, rear and side panel of the GPON ONU as follows.
Front Panel
REAR PANEL
ONU Rear Panel Description
SIDE PANEL
ONT Bottom Panel Description
ONU Installation
The chapter describes the required installation operations before you use the
device for the first time.
Product Networking Application – FTTH
Fiber to the Home (FTTH) means to install the ONU to residences or enterprise
buildings. The optical line ternminal (OLT) is placed in the central equipment
room. The ONU can be placed in the home of a user, or it can provide
connection for the user through the Ethernet interface, according to the user
requirement. The OLT connects to the ONU with an optical distributor in the
point-to-multipoint way. See the following figure.
Note:
The ONU applies to installation at home or in the corridor. Because
installation and cabling in the corridor are relatively complex, let the
professional engineers deploy according to the actual situation. This manual
describes the procedure for installing the device at home, and is for
reference only.
Installation Preparations
The Ethernet interface of your computer connects to the Ethernet interface of
the ONU. Before instaling it, ensure that an Ethernet adapter is already
installed in your computer.
Connecting ONU
Connecting the Network Cable
Step 1 Use the one end of the network cable to connect the Ethernet interface
of the computer. Step 2 Use other end of a network cable to connect the
Ethernet interface on the rear panel of the HALNy HL-4GMV2.
Connecting the Fiber
Caution
- When a fiber is not in use, ensure to cover the optical interface of the ONU and the dust cap of the optical fiber. Prevent grease, dust pollution or water immersiorn, which may lead to unavailable fiber and optical interface of the device.
- If fibers need to be fixed or bended during cabling, do not fasten the fibers too tight. Avoid fiber extrusion, which may lead to increase of fiber material or unavailable fiber.
Connecting the Power Adapter and Power Cord
- Connect the output end of the power adapter included in the device package to the input end of the power supply of the ONU,
- Insert one end of the power cord attached with the device into the input end of the power adapter. Insert the other end of the power cord into the power socket,
- Check whether the Power indicator is on. If it is on, the power supply is normal.
- Otherwise, check whether the power cord and the power adapter are correctly connected.
Troubleshooting
Technical Specification
Appendix A Acronyms and Abbreviations
Warning:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user s authority to operate the
equipment.
NOTE
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. Thesse limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference t radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on ,the user is encouraged t try t0 correct the interference by one Or
more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Recycling
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE) This product must be handled according to European directive 2012/19/EU in order to be recycled or dismantled. This will minimize the negative effects on the environment and human health means that this resulting from the possibility of the presence in the equipment hazardous components. A user can give the substances, mixtures and product to a competent recycling organization, to WEEE collection points or to a distributor (in accordance with local regulations).