COOLER MASTER Synk X 5.8 Ghz Transmitter User Manual

COOLER MASTER Synk X 5.8 Ghz Transmitter

OPERATING INSTRUCTIONS

1. Turn on the power switch of the 5.8Ghz Transmitter.
2. Connect the audio source
3. Use the dial to select the corresponding audio input.
4. Select optical digital input. The audio source must be a PCM signal. Transmiter does not support surround sound decoding.
5. If the 5.8Ghz transmitter has not been paired with SynkX Haptic chair, you need to complete the pairing process first.
6. Power on Synk X Haptic chair
7. Switch mode to 5.8Ghz Transmitter.
8. When the connection is successful the LED on the upper side of the Synk X Haptic chair Pairing will be white and the LED on the 5.8Ghz transmitter is always on.
9. The audio source needs to be adjusted to appropriate volume to avoid cracking sound.

Caution:
If the LED of the 5.8Ghz transmitter or Synk X Haptic Chair is blinking, it means that the wireless signal is blocked or out of the receiving range, resulting in a signal failure, or the frequency pairing is not successful. In this case, you need to correct the position of the transmitter host or re- pair.

NAMES AND FUNCTIONS

PAIRING INSTRUCTIONS

1. Turn on the power switch of the 5.8GHz transmitter and Synk X Haptic Chair.
2. Synk X selects 5.8Ghz Transmitter Mode, at this time the white LED flashes.
3. Press and hold the Synk X Haptic Chair PAIRING button for 3 seconds. The LED will flash quickly to enter the pairing mode.
4. Press and hold the PAIRING button on the 5.8Ghz transmitter for 5 seconds. The LED will flash quickly to enter the pairing mode.
5. The pairing process is completed when the LEDs on both sides stay solid.

REGULATORY STATEMENTS

United State
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

Un-license band: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation. (15.21)

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.

1. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons.
2. This Transmitter must not be c o-located or operating in conjunction with any other antenna or transmitter
   This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Increase the separation between the equipment and receiver.
2. Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.
3. Consult the dealer or an experienced radio/TV technician for help.

Canada
Canada, ISED notice:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

NOTICES

1. To avoid interference with wireless transmission do not place or use the 5.8Ghz transmitter near a magnetic environment or iron.
2. Do not drop or expose the 5.8Ghz transmitter to excessive g-forces.
3. Do not expose the 5.8Ghz transmitter to extremely high or low temperatures.
4. The 5.8Ghz transmitter is not waterproof. Avoid any exposure to liquids and moisture.
5. Cleaning the 5.8Ghz transmitter must only be done with a soft and dry cloth.
6. The 5.8Ghz transmitter requires a 5V DC power supply. Higher voltages will damage the unit.

TROUBLESHOOTING

A. The Synk X Haptic Chair has no sound or vibration after turning on the transmitter

1. Confirm the 5.8Ghz transmitter and the Synk X Haptic Chair are paired
2. Confirm the sound source has been connected to the input hole of the 5.8Ghz transmitter. Adjust to the corresponding mode
3. Confirm that the LED indicator light above the PAIRING button on the interface of the Synk X Haptic Chair is on without flashing indicating the connection has been made

B. 5.8Ghz transmitter uses S/PDIF input but the Synk X Haptic Chair has no sound and vibration

1. Confirm that the SELECT button is adjusted to the corresponding position for OPTICAL
2. Confirm the audio source is a PCM output. The transmitter does not support DTS/Dolby surround sound effects.

C. When the Synk X Haptic chair receives an unstable signal it disconnects

1. Make sure that there is no obstruction in front of the 5.8Ghz transmitter or between the 5.8Ghz transmitter and the Synk X Haptic Chair.
2. The transmitter range is 10 meters with line of sight. Reduce the distance and try again.

D. The volume of the Synk X Haptic Chair is low

1. Increase the volume of the audio source, then adjust the vibration intensity on the Synk X Haptic Chair.
2. If the volume of the audio source is too low it will affect the vibration intensity of the  Synk X Haptic chair.

E. No sound after earphones are connected to the AUDIO OUT jack of the transmitter

1. Confirm the input source is ANALOG input. The OPTICAL jack does not support AUDIO OUT.
2. If the audio source input is Subwoofer’s PRE-OUT, you cannot hear the low-frequency audio.

If the problem is not solved after you have completed the above steps, please contact customer service

References

• Home | Cooler Master

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>