SAGITTER HL F4 Fresnel 230W LED User Manual
- June 9, 2024
- SAGITTER
Table of Contents
SAGITTER HL F4 Fresnel 230W LED
INTRODUCTION
Thank You for choosing one of Our products!
Please refer to the instructions and warnings contained in this user manual,
please retain it for future reference.
This manual contains information about the installation and use of the device.
The information contained in this publication has been carefully prepared and
checked. However it is not assumed any responsibility for any inaccuracies.
All rights are reserved and this document can not be copied, photocopied,
reproduced in whole or in part without previous written permission of PROEL.
PROEL reserves the right to make, without notice, any aesthetical, functional
or design changes or modifications in everyone of its products. PROEL doesn’t
assume any responsibility for the use or application of the products here
described.
The crossed bin symbol, shown on the product or on accompanying documents,
indicates that the product should not be disposed with other household waste
at the end of the lifecycle. To avoid any damage to the environment, the user
is encouraged to separate this product from other kinds of wastes and recycle
it responsibly to promote the sustainable reuse of material resources. Home
users are encouraged to contact the retailer where they purchased this product
or their local government office for details on separate collection and
recycling this type of product. Business users are encouraged to contact their
supplier and check the terms and conditions of the purchase contract. This
product should not be mixed with other commercial waste.
- The lightning symbol with arrow in an equilateral triangle intends to alert the user to the presence of not insulated “dangerous voltages” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
- The exclamation point symbol within an equilateral triangle intends to alert the user to the presence of important instructions for use and maintenance on the accompanying documents of the product.
- The “F” inside an equilateral reversed triangle means that the product is suitable for mounting on normally flammable surfaces.
- The product to which this manual refers comply with the European Directives pursuant to the safety of electrical equipment supplied at low voltage (LVD) and to the Electromagnetic Compatibility (EMC)
SAFETY INSTRUCTIONS
Caution! This product is not suitable for household illumination.
Please read this manual before installing and applying power to the equipment,
follow the safety precautions listed below and observe all warnings in this
manual and printed on. Please contact a PROEL distributor for assistance with
any questions about how to activate the equipment safely. Contact a qualified
technician for any maintenance work not described in this manual. Do not
modify the fixture or install accessories and upgrade kits that are not the
Proel original ones.
People involved in the installation and maintenance of the device must:
- Be qualified
- Follow the instructions of this manual in the theaters, in the halls, in the places where the events take place, etc.
CHECKS BEFORE INSTALLATION
Make sure all the parts for fixing the product are in good condition.
Make sure that the anchor point is stable before positioning the product.
The safety cable must be properly attached to the device and fixed to the
supporting structure so that, in case of failure of the primary supporting
system, it has the lowest possible fall of the device. If the safety cable
wear, must be replaced with an original spare.
MINIMUM DISTANCE OF ILLUMINATED OBJECTS
The projector must be positioned so that the objects hit by the beam of light
are at least 2 meters from the lens of the projector.
MINIMUM DISTANCE FROM FLAMMABLE MATERIALS
The product must be positioned so that any flammable material is at least 0.50
meters from any point of the surface of the device. Never place filters or
other materials over the lens or on the optical axis.
MOUNTING SURFACES
The device is suitable for mounting on normally flammable surfaces.
REFERENCE TEMPERATURE
The ambient temperature range of use of the device varies between + 5 ° C
(min) and + 40 ° C (max), outside of that range the device should not be used.
The maximum temperature of the housing Tb = 80 ° C must never be exceeded. Do
not block the exhaust fans, ensuring a minimum clearance of 0.5 meters around
the ventilation holes.
IP20 PROTECTION RATING
The device is protected against the penetration of solid bodies larger than 12
mm (0,47 “) in diameter (first digit 2), but not against dripping water, rain,
splashes or jets of water (second digit 0). Use only in dry areas. Inside use
only. Do not expose the equipment to rain or moisture.
PROTECTION AGAIN ELECTRIC SHOCK
The device must be connected to a power supply system with efficient earthing.
Moreover, it is recommended to protect power supply lines of the product from
indirect contact and / or shorting to earth by using appropriately sized anti
electrical shock switch.
CONNECTION TO THE MAINS
The electrical connection must be carried out by a qualified electrician.
Ensure that the mains frequency and voltage correspond to those for which the
equipment is designed, as shown in the electrical data label. This label also
shows the power consumption that is necessary to refer to evaluate the maximum
number of devices to be connected to the electricity line, in order to avoid
power overloading.
If the external power cord of this light is damaged, it must be replaced with
a special cord exclusively available from Your PROEL dealer.
Never operate the equipment with lenses and / or covers missing or damaged. In
case of non-use, it is recommended to unplug the projector from the mains.
MAINTENANCE
Before starting any maintenance or cleaning the product, disconnect the power from the mains and disconnect the power cable from the device. After switching off, do not remove any part of the device for at least 35 minutes to avoid the risk of burns. The lenses, if damaged, must be replaced with original spare parts.
WARNING
CAUTION. Do not look directly at the light source. Do not look at the beam with lenses, glasses, mirrors or similar optical instruments that could change the convergence of light, causing serious damage to people and / or things.
WARNING! DANGER FOR THE EYES! Do not look directly at the light source
OPENING AND CONTROL
Carefully open the package, check the content and make sure that all the parts
are present and are in good condition. In cases where some parts are not
present or are damaged, immediately contact Your supplier and retain the
packaging for verification.
WARNING!
If the product has been exposed to drastic temperature changes, let the unit
turned off until it reaches room temperature because the presence of
condensation can damage the product if it is turned on.
Verify that the box contains the following items:
- N° 1 SG HLF4 / SG HLF2
- N° 1 Barndoor
- N° 1 Power supply cable
- N° 1 User manual
FRONT VIEW
- Lens
- Manual dimmer knob
- Display + buttons
- Bracket
REAR VIEW
- USB connector for software upgrade or wireless antenna (optional)
- Fuse
- Power IN connector
- Power OUT connector (max 8A)
- Manual zoom knob
- 3/5 poles DMX IN/OUT
INSTALLATION AND SWITCH ON
PRODUCT INSTALLATION
Do not shake the device. Avoid the use of too much force during
installation or unit fixing. The unit can be installed on the floor resting on
the rubber feet, on the wall, ceiling or on a truss.
WARNING! IT’S REQUIRED
the mounting of the safety rope (PLH232 – PLH248) sold separately) in the case
where the product is hung on a wall, ceiling or on a truss. Except when the
device is placed in the floor, the safety cable is always required.
CONNECTION TO THE MAINS
The device must be connected to a power supply system with a proper earth system. Moreover, it is recommended to protect power supply lines of the products from indirect contact and / or shorting to earth by using appropriately sized anti electrical shock switch. The electrical connection must be carried out by a qualified electrician. Ensure that the mains frequency and voltage correspond to those for which the device is designed, as shown in the electrical data label.
CONNECTION TO THE DMX CHAIN
Use a cable conforming to specifications EIA RS-485: pole twisted, shielded,
120Ohm characteristic impedance and low capacity (SAGITTER SG DMX3 – SG DMX5).
Do not use microphone cable or other cable with different characteristics than
those specified. Terminations must be made with male / female XLR 3-pin
connectors. You must enter on the last device a terminal plug with a 120Ohm
resistance (min1 / 4 W) between terminals 2 and 3. IMPORTANT: The cables must
not come into contact with each other or with the metal housing of the
connectors. The housing itself must be connected to the shield braid and to
pin 1 of the connectors.
SETUP
MENU
Note: in grey color the default values
| Level 1 | Level 2 | Level 3 | Level 4 | Comments |
|---|
DMX SETTINGS
| DMX ADDRESS| 001 – 512| | Dmx address
DMX CHANNEL MODE
| DIMMER
01CH
| | 1 channel mode: only
dimmer
DIMMER 16 BIT
02CH
| | 2 channels mode: dimmer
and dimmer fine
02CH
02CH
| | 2 channels mode: dimmer
and strobe
STANDARD
04CH
| | 4 channels mode: see
details
EXTENDED
05CH
| | 5 channels mode: see
details
NO DMX STATUS| HOLD LAST| | Last status if DMX lost
BLACK| | Black out if DMX lost
PERSONALITY
| SLAVE| OFF| | Slave mode
ON|
DIM MODES| LED| | LED dimmer mode
HALOGEN|
DIM CURVES
| LINEAR| |
Dimmer curves
SQUARE|
I-SQUARE|
S-CURVE|
FANS
| AUTO| |
Fans speed
HIGH|
SILENT|
REFRESH RATE
| 900 Hz| |
LED refresh rate
1000 Hz|
1100 Hz|
1200 Hz|
1300 Hz|
1400 Hz|
1500 Hz|
2500 Hz|
4000 Hz|
5000 Hz|
10 KHz|
15 KHz|
20 KHz|
DISPLAY
|
SCREEN SAVER DELAY
| 10 s|
Display backlight off
20 s
30 s
40 s
50 s
1 min
2 min
3 min
4 min
5 min
10 min
SCREEN LOCK
| OFF|
Display lock
10 s
20 s
30 s
40 s
50 s
1 min
2 min
3 min
| | | 4 min|
---|---|---|---|---
5 min
10 min
USB UPDATE (1)| NO| | USB update
YES|
SERVICE (2)
| CALIBRATION| WHITE 000 – 255|
Pwd = 050
FACTORY RESTORE| YES / NO
EDIT RDM UID| XXXXX XxXXXX
MANUAL CONTROL
| DIMMER| 000 – 255| | Manual dimmer control
STROBE
|
000 – 255
| | Manual strobe control (for details see the DMX
table)
INFORMATION
| FIXTURE LIFETIME (3)| Power On Time (3)| xxxxx h (3)|
FIX LAST RUNTIME (4)| PowrOnTimAbleRes (4)| xxxxx h (4)|
PowerOnTimeReset (4)| Pwd = reserved|
TOTAL LAMP HOURS (5)| xxxxx hours (5)| |
FIXTURE TEMP
|
LEDs
| CURRENT (6)
120F / 49C
|
MAX RESETTABLE (7)
260F / 127C
|
MAX NOT RESETTABLE (8)
260F / 127C
|
LAST MAX TEMP RESET
Passcode = 038
|
DMX VALUES| DIMMER
000
| | Current DMX values
PRODUCT ID| RDM UID| aaaa-bbbb-cccc (9)|
ERROR LOGS| FIXTURE ERRORS| NONE|
RESET ERROR LOGS| NO / YES|
SOFTWARE VERSION| V1.01A| |
NOTES:
- In order to know how to use this function, please refer to the section USE OF USB CONNECTOR
- Inside the function SERVICE it is possible to do following operations:
- Calibration of the max intensity of the white
- Reset to default values (in grey color in the table of MENU)
- Modification of RDM UID. Inside this submenu there are 2 numbers. The number on the right is decimal type and it is possible to modify, the number on the left is hexadecimal type. The modification of this second number is automatic, basing on the modification of the decimal part on the right. It is suggested to avoid modifications on these numbers in order to avoid to lose the tracking of the projector.
- Current Power On time. This value automatically resets when the projector is OFF.
- Total working time. This value is resettable. It can be useful to reset this value when, for example, the led is replaced, in order to calculate the total lifetime of the new LED.
- Total working time. Not resettable
- Current temperature
- Max temperature resettable with Pwd = 038
- Max temperature not resettable
- RDM UID it consists of 12 digits: aaaa-bbbb-cccc
- aaaa: manufacturer ID (1221 = Sagitter)
- bbbb: series ID (006E = HLF4T/D – 0002 = HLF2T/D))
- cccc: specific ID of each projector. When the UID is modified in the submenu SERVICE, only these 4 digits are modified.
USE OF THE MANUAL DIMMER CONTROL KNOB
- Press the knob
- Rotate until the desired intensity
- Press again for confirmation
MASTER / SLAVE MODE
- With the projector still not connected in chain, select the Master projector and set all the slave as SLAVE = ON mode
- Connect the projectors in chain with XLR cables and the master as first of the chain
- Adjust the functions of the master with the manual dimmer control knob (after press to confirm) or by using the settings under the submenu MANUAL CONTROL
- If you want to pass from the Master/Slave chain to a DMX chain, disconnect all the projectors from the chain, set the DMX mode in all the projectors and reconnect them. For more details refer to the note after the DMX tables.
DMX MODE
1-channel mode (Dimmer)
| Channel | Function | Values | Description |
|---|---|---|---|
| 1 | Dimmer | 000 – 255 | Master dimmer from 0 to 100% |
2-channels mode (Dimmer 16 bit)
| Channel | Function | Values | Description |
|---|---|---|---|
| 1 | Dimmer | 000 – 255 | Master dimmer from 0 to 100% |
| 2 | Dimmer fine | 000 – 255 | Dimmer fine |
2-channels mode (02CH)
| Channel | Function | Values | Description |
|---|---|---|---|
| 1 | Dimmer | 000 – 255 | Master dimmer from 0 to 100% |
2
| ****
Strobe
| 000 – 031| Led ON
032 – 063| Led OFF
064 – 095| Strobe from slow to fast
096 – 127| Open
128 – 159| Pulse IN from slow to fast
160 – 191| Open
192 – 223| Random strobe from slow to fast
224 – 255| Open
4-channels mode (Standard)
| Channel | Function | Values | Description |
|---|---|---|---|
| 1 | Dimmer | 000 – 255 | Master dimmer from 0 to 100% |
| 2 | Dimmer fine | 000 – 255 | Dimmer fine |
3
| ****
Strobe
| 000 – 031| Led ON
032 – 063| Led OFF
064 – 095| Strobe from slow to fast
096 – 127| Open
128 – 159| Pulse IN from slow to fast
160 – 191| Open
192 – 223| Random strobe from slow to fast
224 – 255| Open
4
| ****
Dimmer mode
| 000 – 020| LED mode (display bypassed)
021 – 040| Halogen mode (display bypassed)
041 – 255| No function: display priority
5-channels mode (Extended)
| Channel | Function | Values | Description |
|---|---|---|---|
| 1 | Dimmer | 000 – 255 | Master dimmer from 0 to 100% |
| 2 | Dimmer fine | 000 – 255 | Dimmer fine |
3
| ****
Strobe
| 000 – 031| Led ON
032 – 063| Led OFF
064 – 095| Strobe from slow to fast
096 – 127| Open
128 – 159| Pulse IN from slow to fast
160 – 191| Open
192 – 223| Random strobe from slow to fast
224 – 255| Open
4
| ****
Dimmer mode
| 000 – 020| LED mode (display bypassed)
021 – 040| Halogen mode (display bypassed)
041 – 255| No function: display priority
5
| ****
Control (wait 3 seconds after selecting the value)
| 000 – 100| No function
101 – 105| LED refresh rate 900 Hz
106 – 110| LED refresh rate 1000 Hz
111 – 115| LED refresh rate 1100 Hz
116 – 120| LED refresh rate 1200 Hz
121 – 125| LED refresh rate 1300 Hz
126 – 130| LED refresh rate 1400 Hz
131 – 135| LED refresh rate 1500 Hz
136 – 140| LED refresh rate 2500 Hz
141 – 145| LED refresh rate 4000 Hz
146 – 150| LED refresh rate 5000 Hz
151 – 155| LED refresh rate 10000 Hz
156 – 160| LED refresh rate 15000 Hz
161 – 165| LED refresh rate 20000 Hz
166 – 200| No function
201 – 210| Dimmer curve LINEAR
211 – 220| Dimmer curve SQUARE
221 – 230| Dimmer curve INVERSE SQUARE
231 – 240| Dimmer curve S-CURVE
241 – 255| No function
IMPORTANT NOTE: DMX mode has priority over all the functions.
When some projectors are connected in DMX chain and after they are connected
to a DMX controller, they automatically pass in DMX mode.
This means that if some of them was set in manual mode, when they will be
connected in DMX chain, they automatically pass in DMX mode. If for any reason
the DMX controller is switched OFF or the DMX signal is lost, all the
projectors of the chain will come back to the previous status and, if in the
chain there are different projectors in manual mode, all of them will be
connected in manual mode in chain that means different masters in chain.
This is not possible and this could generate strange behaviours and
interferences in the chain until the DMX controller will be connected again.
When a DMX chain must be created, all the projectors must be set in DMX mode
before the connection, in order to avoid strange situations before described.
If you want that in a DMX chain, when the signal is lost, the projectors must
go in a specific condition, it must be used the function NO DMX STATUS under
the submenu DMX SETTINGS.
MAINTENANCE
To ensure optimal performance, the unit must be frequently cleaned. Unplug the
device from the mains and let it cool for at least 35 minutes to avoid the
risk of burns. Use a vacuum cleaner or an air compressor and a soft brush or a
lens cloth to remove the dust deposited.
The lenses, like any other damaged part, must be replaced with original spare
parts.
TECHNICAL SPECIFICATIONS
-
Power Supply: 100-240V, 50/60HZ
-
LED: 230W (HL F4) – 130W (HL F2)
-
Adjustable Zoom:
HL F4: da 9° a 51° Beam – da 13° a 62° Field
HL F2: da 14° a 36° Beam – da 20° a 47° Field -
Power consumption: 260 W @230 VAC (HL F4) – 150 W @230 VAC (HL F2)
-
Operation Mode: Manual mode, Master/slave, DMX512
-
Electronic Dimming 0-100%
-
DMX 1, 2, 2, 4, 5 Channels
-
Blue LCD graphic display for address and function setting
-
Dimensions (L x H x D):
HL F4: mm. 357x401x404
HL F2: mm. 320x380x386 -
Weight: HL F4: kg. 8,7
HL F2: kg. 7
Contact Us
Sagitter is a brand of PROEL SPA (Worldwide Headquarters) Via alla Ruenia, 37/43
- 64027 SantOmero (TE) – ITALY
- Tel.+39 0861 81241
- Fax +39 0861 887862
- P.I. 00778590679
- N.Reg.AEE IT 08020000002762
- sagitter.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>