BODY SLEEP HC209705102 Queen Size Linen Upholstered Bed Instruction Manual
- June 9, 2024
- BODY SLEEP
Table of Contents
Reunion/Chateau/Lucena Twin/Double/Queen Bed
Assembly Instruction
Contains One Bed and Hardware
Instruction Manual
HC209705102 Queen Size Linen Upholstered Bed
IMPORT ANT NOTE:
For customer support please call:
314-993-2693
For customer support please call:
314-993-2693
Carefully remove all the parts from the box. Arrange on a flat surface and
verify you have all of the following parts and hardware
TOOLS REQUIRED:
Phillips Screwdriver
PARTS LIST
A.Headboard (1 pc)| B.Headboard Legs (2 pcs)| C.Side Rail (4 pcs)
D. Footboard (1 pc)| E. Side Rail Support Leg (2 pcs)| F.Center Leg (4 pcs)
G. Footboard Legs (2 pcs)| H.Wood Slat (4 pcs)| I. Side Rail Slat Support (4
pcs)
HARDWARE LIST
1.20mm Bolt (8 pcs)| 2.Flat Washer 14 (14 pcs)| 3.Spring Washer (14 pcs)| 4.
Wood Dowel M8 (4 pcs)
---|---|---|---
5.30mm Bolt (20 pcs)| 6.40mm Bolt ( 4 pcs)| 7. 50mm Bolt (6 pcs)| 8. 70mm
Bolt (2 pcs)
9.32mm Screw ( 8 pcs)| 10.Adjuster (4 pcs)| 11.Small Hex Key (1 pc)| 12.Large
Hex Key (1 pc)
ASSEMBLY INSTRUCTIONS
STEP 1
Attach headboard legs(Part B) to the headboard(Part A) using three 50mm
bolts (Part 7) and three spring washer(Part 3) and three flat washer (Part 2)
per leg. Secure tightly using small hex key(Part 11).
This headboard is adjustable. To make the Headboard taller (47″ from floor to
top of headboard), attach the headboard legs to the bottom 3 holes. To make
the headboard shorter (45″ from floor to top of headboard), attach the
headboard legs to the top 3 holes.
Attach the footboard legs(Part G) to
the footboard(Part D) using two wood dowel M8(Part 4) and one 70mm bolts(Part
8) and small hex key(Part 11). Secure tightly.
STEP 2
Attach the side rail legs(Part E) to the side rails(Part C) using four 30mm
bolts (Part 5) and four spring washer(Part 3) and four flat washer(Part 2).
Tighten using small hex key(Part 11).
Attach the four side rail supports(Part I) to the side rails(Part C) using
twelve 30mm bolts(Part 5) and small hex key(Part 11). Tighten the bolts.
STEP 3
Attach the eight 20mm bolts(Part 1) to the headboard leg(Part B)and
footboard(Part D) using the large hex key(Part 12). Do not tighten.
Attach the complete side rail to headboard(Part A) and footboard (Part D) by
sliding the side rail brackets onto the bolts on the headboard legs(Part B)
and footboard(Part D). Do not tighten yet.
STEP4
Attach four center leg(Part F) to the slats(Part H) using 40mm bolt(Part
6). Tighten the bolt using small hex key(Part 11). Repeat the step for all
four support leg.
Attach the adjuster leg(Part 10) to the center leg (Part F). Make any
adjustment necessary to ensure the legs are touching the floor.
STEP 5
Place the four slats into the bed as shown. Tighten the bolts on the
headboard legs and footboard using large hex key (Part 12). Secure the 4 slats
using eight screws(Part 9) and a Phillips Screwdriver. Your bed is now set up
and ready for use.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>