parkell D722 Detachable Handpiece Instruction Manual
- June 9, 2024
- parkell
Table of Contents
**parkell D722 Detachable Handpiece Instruction Manual
**
Use of Autoclavable Detachable Handpiece
IMPORTANT: Handpieces are not sterile upon receipt and must be sterilized prior to f rst use as per the instructions below.
To attach the handpiece to the TurboSensor®+ cable, line up the arrow mark on the cable connector to the arrow mark on the handpiece connector and push the two gently together until you hear a click (Figures 1-3). The click indicated the locking mechanism has engaged.
To disconnect the handpiece from the cable, hold the handpiece in an upright position and rotate the quick-lock connector ¼ turn to the left (Figure 4). This will disengage the locking mechanism, so the handpiece can be gently separated from the cable (Figure 5).
Cleaning and Infection Control
- Consult www.CDC.gov for the “Guidelines for Infection Control in Dental Health-Care Settings” and “Statement on Reprocessing Dental Handpieces”.
- DO NOT AUTOCLAVE THE TURBOSENSOR®+ WITH DETACHABLE HANDPIECE CONTROL UNIT, as autoclave heat will destroy it. The control unit should be cleaned of debris with a water-damp paper towel, disinfected by wiping with a paper towel that has been saturated with an EPA-registered low-level (HIV/HBV claim) to intermediate-level (tuberculocidal claim) hospital disinfectant, wiped of chemical residue with a water- damp paper towel, and dried. Utilize the surface disinfecting protocol of the disinfectant manufacturer.
- Autoclaving does not remove debris that has accumulated on the handpiece. Failure to adequately remove debris will result in inadequate sterilization. The handpiece must be washed in soap and water manually and rinse the device under warm running water for 30 seconds to remove any external or internal soil or debris. Using a soft soapy cleaning brush to assist in the cleaning, if necessary. Use non-ammoniated detergent or dishwashing soap. Do not use ammoniated cleansers or disinfectants. Rinse the item again under warm running water for 30 seconds to remove any residual soap and blot dry with adry lint-free towel. Wipe device with a lint-free towel that has been saturated in an EPA-approved, hospital-grade intermediate or high-level disinfectant (minimum 2.5% Glutaraldehyde solution), following the instructions for use provided by the disinfectant manufacturer. Dry with a dry lint-free towel.
- Detachable, Autoclavable Handpiece and inserts shall be sterilized in any conventional steam autoclave following manufacturer’s instructions. A typicalsteam sterilization cycle is 132 +/ 2°C for 4 mins. (Vacuum) or 132 +/ 2°C for 15 mins. (Gravity), followed by a 15 minute minimum cool-down period. Use a steam sterilization pouch that is compliant with ISO 11140-1 Type 4 and ISO 11607-1 standards. Once items are sterilized, adhere to the shelf-life specifed by the pouch manufacturer. After sterilization, inspect the device in the autoclave bag for integrity. If suspicion about the item exists, discard it and order a replacement from Parkell or your dealer.
- DO NOT USE DRY HEAT OR CHEMCLAVE THE HANDPIECE.
- The handpiece from Parkell is designed to withstand a minimum of 1000 autoclaving cycles when reprocessed as per the recommended procedure.
Questions?
If you have any questions contact Technical Support Service at
800-243-7446,
M-F from 8:30 AM to 5:00 PM EST or e-mail
[email protected].
Explanation of Symbols Used
Medical Safety Classifcation Symbol
Qualifed User Symbol
Temperature limitations
Do not use if package is damaged
Follow instructions for use
Keep dry
Sterilizable in a steam sterilizer (autoclave) at the temperature specifed
Package contents
Manufacturer
Catalogue / stock number
Unique Device Identifer
Medical Device
Do not dispose this product into the ordinary municipal waste or garbage system
Parkell, Inc.
300 Executive Dr., Edgewood, NY 11717 USA
TEL 800-243-7446
E MAIL www.parkell.com