ROCKY TALKIE RTMRV2 Mountain Radio User Manual

ROCKY TALKIE RTMRV2 Mountain Radio

Overview

FCC&RSS Warning

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

SAR tests are conducted using standard operating positions accepted by FCC/ISEDC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model is a available for sale to the public, it must be tested and certified to the FCC/ISEDC that is does not exceed the exposure limit established by the FCC/ISEDC. Tests for each product are performed in positions and locations as required by the FCC/ISEDC.

For body worn operation, this device has been tested and meets the FCC/ISEDC RF exposure guidelines when used with an accessory designated for this product when used with an accessory that Contains no metal.

To maintain compliance with the FCC/ISEDC’s RF exposure guidelines, hold the transmitter and antenna at least 1 inch(2.5 centimeters) from your face and speak in a normal voice, with the antenna pointed up and away from the face.

This equipment complies with FCC/ISDC radiation exposure limits set forth for an uncontrolled environment. In order to comply with the FCC/ISEDC RF exposure requirements, the antenna installation must comply with the following:
Users must be fully aware of the hazards of the exposure and the ability to exercise control over their FCC exposure to qualify for the higher exposure limits.
Your wireless hand-held portable transceiver contains a low-power transmitter. This product sends out radio frequency(RF) signals when the Push-to- Talk(PTT)button is pressed.
The device is authorized to operate at a duty factor not to exceed 50%.
The device complies with FCC/ISEDC license-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Technical Specifications

General

Transmitter

Output power| High Power: 31.83dBm

Low Power: 25.79dBm

---|---
Modulation mode| FM
Maximum deviation| <2.5KHz
Spurious radiation| <7.5uW
Adjacent Channel Power| <-60db

Receiver

Battery Information

Charging Li-ion Battery

Please charge the battery before using. Completing a charge-discharge cycle two times can make
the battery capacity achieve its maximum high-point. When the battery power is low, please recharge the battery.

Applicable Battery Type
Please use the designated battery only. Using other batteries may result in accidents or injury.

The procedure of charging:
Use only the charger and battery. The charger LED indicator light will indicate the charging process.

Warning:
For safety, the lithium battery is not charged before shipment.

1. When charging, it is recommended to tum off the radio.
2. Charge directly with USB plug.
3. While charging, the indicator light will turn red.
4. The battery will take approximately 4 to 5 hours to achieve a full charge. When the charging is completed, the indicator light will turn green.

FREQUENTLY ASKED QUESTIONS

How do I know if the radio is off?
After 10 seconds of inactivity, the radio enters standby mode and the screen goes dark. The radio is not off! To fully turn off the device, hold the power button until you hear the double beep.
What are privacy codes?
Activating a privacy code (also called a sub-channel) will filter out transmissions from other radios that are not using the same privacy code. A channel has a privacy code enabled if it shows CT or DCS on the screen.
How do I know if the radio is fully charged?
There is a small indicator light near the charging port on the radio. It will light up red while charging and change to green when the battery is fully charged.
What are High and Low power modes?
he device has two options for transmission power: High 2W) and Low (0.5W). High power will improve range and audio quality in some situations. The active power setting is indicated on the screen as Hor L.
Why won’t my radio transmit?
When the battery is under 159%, the radio will prevent you from transmitting in order to protect the battery. 1he radio can still receive transmissions.
What is the SCAN function?
The SCAN function cycles through channels 1 to 22 until an active transmission is found. Use this to find other radio users in your area. Press any button to stop scanning.

CONNECT TO OTHER RADIOS

The Rocky Talkie is compatible with other brands of FRS radios. Follow these simple steps for connecting to another radio:

1. Start by matching the channel (use channels 1 through 22 on the Rocky Talkie)
2. Match the privacy codes on both radios (see inside for how to alter the Rocky Talkie privacy code).
   Some radios do not conform to the 22 standard FRS channels. To connect to these radios, try reviewing their user manual and use the chart below to match the frequencies for a given channel

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>