ZEVNI L33IZUZUW4929SY8 Fortuno 3-Light White Vintage Chandelier Instruction Manual
- June 9, 2024
- ZEVNI
Table of Contents
- ZEVNI L33IZUZUW4929SY8 Fortuno 3-Light White Vintage Chandelier
- Item Number: A04929
- IMAGE FOR FINISHED PRODUCT:
- PARTS TYPE & QTY INCLUDING:
- ACCESSORIES & QTY ENCLOSED:
- ASSEMBLY & INSTALLATION INSTRUCTIONS:
- 3. Turn off power
- 4. Make installation
- COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
- 5. Check everything is already installed properly, then you could turn
- ORDERING PARTS.
- CLEANING.
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZEVNI L33IZUZUW4929SY8 Fortuno 3-Light White Vintage Chandelier
Item Number: A04929
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done. » Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position. -
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED Before starting assembly and installation please prepare the
needed
(NOT INCLUDED): tools as below picture
PARTS TYPE & QTY INCLUDING:
(C) Single bar (1) (D) Green ground screw (1) (E) Canopy (1) (F) Collar ring
(1) (G) Collar loop (1) (H) Quick link (2) (I) Chain (1) (J) Loop (1)
(K) Fixture loop assembly (1) (L) Tube (1) (M) Stem (1) (N) Smaller chain (3)
(0) Sockets assembly (1) (P) Iron ring (1) (Q) Hook (111) (R) Wood drop (111)
ACCESSORIES & QTY ENCLOSED:
(A) Wire connector (3)
(B) Mounting screw (2)
(Q) Hook (2) (Spare parts)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Make pre-installation
Step A1 » Screw tube (L) and stem (M) together onto the top of sockets assembly (O).
Step A2 » 1) Pass fixture wires through fixture loop assembly (K).
- Screw tube (L) onto the bottom of fixture loop assembly (K)
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
Step B1 » By measuring, determine the correct number of links needed for
proper hanging height. Using the chain pliers, disconnect and discard the
unwanted part.
Step 82 » Attach quick link (H) to chain (I) and loop (J) on the top of
fixture loop assembly (K). Step 83 » Carefully weave the fixture wires through
chain (I) in and out of every other link and stop just when you reach the top
of chain (I). Gently pull the wires to ensure the wires are not stressed.
3. Turn off power
Before you start the installation, NEVER attempt any work without shutting off
the electricity until the work is done
» Go to the main fuse, or circuit breaker, box in your home. Place the main
power switch in the “OFF” position.
» Place the wall switch in the “OFF” position
4. Make installation
Step C1 » Remove collar ring (F) from collar loop (G). Attach single bar (C)
to the outlet box with mounting screws (B)
Step C2 » Raise canopy (E) over collar loop (G) and screw collar ring (F) to
measure a proper position. Unscrew collar ring (F) from collar loop (G) and
remove canopy (E). Refer to the following note, you would know the proper
position where collar loop (G) should be located.
NOTE: canopy (E) should be snug against the ceiling and collar loop (G) should
be screwed enough threads (no less than 6 threads) on the pre-assembled
threaded nipple
for more secure hanging.
If not, adjust collar loop (G) on single bar assembly (C) by screwing collar
loop (G) in or out of single bar (C) until the secure length is achieved
Step C3 » Pass chain (I) through collar ring (F) and then through canopy (E).
Step C4 » Open quick link (H), attach quick link (H) to collar loop (G). Close
quick link (H). Pass the fixture wires through collar loop (G) to the top of
the pre-assembled threaded nipple and gently pull to ensure the wires are not
stressed. Step C5 » If needed, shorten the length of fixture wires. At this
point, the remaining wire length measured above single bar (C) is at least 6″.
Step C6 » Make wire connections Connect wires as below wires connection shown.
PLEASE NOTE THAT GROUND WIRE IS BARE
COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
● Twist wires together with plastic wire connectors until tightly joined.
● Wrap each connector with approved electrical tape.
● Be sure that no wire strands are exposed and then carefully tuck all wires
into the outlet box.
Step C7 » Raise canopy (E) to the ceiling and secure canopy (E) in place by
tightening collar ring (F) onto collar loop (G).
Step C8 » 1) Install bulbs (not included) (Please do not exceed the maximum
wattage recommended on the socket.)
2) Attach all the wood drops (R) to iron ring (P) with hooks (Q) as shown in
the illustration
5. Check everything is already installed properly, then you could turn
on the light. Enjoy!
ORDERING PARTS.
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING.
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>