mifa Wildrock Bluetooth Speakers User Guide
- June 9, 2024
- MiFa
Table of Contents
mifa Wildrock Bluetooth Speakers
PACKING CONTENT
POWER ON
BLUETOOTH CONNECTION
MODE SWITCH
PLAY
HANDS-FREE CALL
LIGHT
MIC
MICROPHONE
CHARGE
Technical Specification
Speaker : 2 x 3inch full-range speaker
Passive Radiators: 90mm x 2pcs
SNR : >89dB
Battery type : Lithium battery (3.7V4500mAh)×2
Charging interface : USB Type-C
Charging time of battery: Approx.4.5 hours (5V/3A)
Music playing time: Approx.13 hours (depending on volume and audio
content, with dynamic light off )
Bluetooth version: 5.0
Hands-free call Yes
Playable format: MP3、WMA、WAV、FLAC APE(Micro SD Card/U disk)
Dynamic light: RGB ambient lighting
Amplifier function Support wireless microphone amplification function
Dimension of product: W307mmH150.5mmD140mm/W12.08″ xH 5.92″ D5.51″
Weight of product: 1773g
This device complies with part 15 of the FCC Rules. Operation is subject to
the fol lowing two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Th is equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help. The
device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction
FCC ID: 2AXOX-WILDROCK
Customer Support
MIFA INNOVATIONS LLC
www.mifa.net Designed in US Made in China
FAQ
When the signal of the microphone is not good or is suck,
Short press “+” ” -” to select the appropriate frequency band from CH0l-CH 10.
When the microphone cannot be connected to the host
Press and hold the ” ” and “-” simultaneously in the power-on state, then “DE” will be displayed on the screen, it will restore to the default settings and reconnect.
If the microphone cannot be turned on
please plug in the charging cable to charge and activate;
How to pair with a new microphone?
While the speaker in power-off state, microphone in power-on state, press and
hold the ” ” and”+” button of the microphone simultaneously, the screen will
display the “ID “and enter the ID paring status.
At this time, the speaker can be automatically paired with the ID when it is
turned on. (After the connection is successful, the speaker will have a beep).
How to clear the ID of the microphone?
Microphone: Press the ” ” and ” -” simultaneously in the power-on state, then
“DE” will be displayed on the screen, it will restore to non ID status.
Note : If the microphone has cleared its ID and needs to be connected to
the speaker again, re-pair the ID according to the method of the new
microphone.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>