noaton TRITON Ceiling Fan Instruction Manual
- June 9, 2024
- Noaton
Table of Contents
noaton TRITON Ceiling Fan
Safety Instructions
Read the user manual carefully before using the device.
Do not attempt to repair, disassemble or modify the appliance, or there may be
malfunction or damage.
The ceiling fan must be installed by a qualified electrician in compliance
with local regulations on electrical installations.
Any work on the electrical connections must be carried out only after the
electric power powering the fan is turned off using a switch or home fuses.
The fan must be installed so that its blades are at least 230 cm above the
ground and their ends at least 30 cm from the nearest obstacle or wall (the
greater the distance, the better the airflow of the fan). The base on which
the mounting bracket is mounted with the supplied screws must be able to
support a load of at least 30 kg. The fan must not sway.
Do not plug the power of the fan to any dimmers, potentiometers, wall switches
and similar devices, as this may cause the fan to malfunction or damage its
motor. The electrical connection must include a circuit breaker in accordance
with the decree on electrical installations, which ensures a single-phase
interruption connected directly to home fuses and must have gaps between all
conductors providing total disconnection according to Overvoltage category
III. The fan must be connected to a protected circuit. Use only the supplied
remote control to turn the fan on and off.
Do not insert any objects into the blade rotation area that may collide with
the blades. Such impact may damage the blades and cause imbalance of the fan
and its vibrations and increase the noise level. After installation, check the
tightness of the individual screws. Loose screws are one of the causes of a
noisy fan.
Due to the rotating motion of the fan, some connections may become loose over
time. Therefore, check all the screws and other connections at least twice a
year and tighten them if necessary. If the power cord is damaged, it must be
replaced by a manufacturer, specialized service centre or other qualified
certified service in order to avoid any malfunction or health hazard.
The lighting of this fan must be replaced only by a manufacturer, specialized
service centre or other qualified certified service in order to avoid any
malfunction or health hazard.
Note : Important warnings and instructions in this user manual do not
cover all possible conditions and situations that may arise. It is always
necessary to use common sense, be cautious and anticipate any possible
situations that may arise.
Use the device at the specified voltage.
The fan is intended for indoor domestic use only. Do not use it for any other
purposes. Do not place the fan near heat-generating equipment or flammable and
hazardous materials. This appliance is not intended for use by persons
(children) with reduced physical, sensory or mental capabilities, or lack of
experience or knowledge, unless they have been instructed in the safe use of
this device or are under the supervision of a person responsible for their
safety.
Parameters
Model | TRITON |
---|---|
Nominal voltage and frequency | 220-240 V ~ AC 50/60 Hz |
Max. engine input power (W) | 35 W |
Lighting input power | 2×21 W (model 12050) |
Luminous flux | 100 lm / W |
Light colours | Warm white / daylight white / cool white (3000K/4000K/6000K) |
Colour rendering index (Ra) | >85 |
Protection class | Class II (model 12050) |
Number of blades / material | 5 / ABS |
Dimmable | Yes |
Maximum slope of the ceiling | 90° (can be installed on a wall) |
Remote control | Yes (IR) |
Fan dimensions (width x height) | 50 x 22 cm (model 12050) |
- Weight| 2,2 kg (model 12050)| 3,25 kg (model 12058)
Model 12050 (Ø 50 cm)
Speed | 1 | 2 | 3 |
---|---|---|---|
Input power (W) | 28 | 31 | 35 |
Rotations per minute | 700 | 900 | 1100 |
Airflow (m3/min) | 35 | 40 | 45 |
Noise level (dB) | 20 | 25 | 30 |
Model 12058 (Ø 58 cm)
Speed | 1 | 2 | 3 |
---|---|---|---|
Input power (W) | 28 | 31 | 35 |
Rotations per minute | 700 | 900 | 1100 |
Airflow (m3/min) | 40 | 45 | 50 |
Noise level (dB) | 20 | 25 | 30 |
Installation
- Mount the supplied mounting bracket to a suitable place on the ceiling or wall using the supplied dowels and screws.
- Disconnect the household power supply. This will prevent the risk of electric shock.
- Connect the conductor from the home circuit to the corresponding conductors coming out of the fan.
- Fix the fan body to the mounted bracket with the screws. Make sure that the conductors are not pinched in any way.
- Check that the screws are properly tightened.
- Restore the power supply.
- The fan is ready for use.
Remote control
The remote control does not require pairing so you may use it immediately upon
installing the fan. Because it is infrared, you can control multiple fans of
the same model at once with a single remote control, provided that they are
within its range.
Given the nature of the infrared signal, the controlled fan must be ideally up
to 4 m away from the remote control. If the distance is longer, the signal may
be attenuated or lost. It is also necessary to ensure that there are no
obstacles between the remote control and the fan and that the remote control
points its upper end (where there is the IR diode) directly to the fan. This
is the only way to ensure trouble-free operation and the maximum user
experience with this fan.
Description of individual remote control functions
Notes on remote control:
Use the central control pad to control the colour and intensity of the LED
lighting. Press and hold the up / down arrows to continuously increase /
decrease the intensity of the lighting (or press for step change).
Press and hold the left and right arrows to change the colour temperature from
warm white (left) to cool white (right) (or press for step change). The middle
button cycles through warm white, daylight white and cool white lighting.
After pressing one of the timer buttons, the fan turns itself off after a
predetermined time (1 or 2 hours). On selected fan models, a button with a fan
symbol with arrows is used to turn on or off the motor that drives the central
grille.
Correct location
- The fan blows air downward in a cone shape and pushes it across the floor. Use this information to choose the most suitable place for the fan, taking into account its function as a ceiling light.
- The parameters of the input voltage must meet the parameters provided on the technical label on the device.
- Make sure that there are no obstacles near the fan that could impede proper airflow or collide with the unit (such as the top cupboard door etc.).
Maintenance
Before performing any maintenance, turn off the fan and disconnect the power supply (ideally by disconnecting it in the fuse box of the household). Clean the surface of the device by a soft damp cloth.
WARNING :
- Do not immerse the fan into water.
- Do not use chemicals, such as detergents, alcohol, thinners or abrasives, to clean the device.
- Prevent water from getting into inside of the device, especially on electronic components. Otherwise, there is a risk of electric shock or damage to the device.
Cleaning and maintenance
The normal operation of the fan causes the screws to gradually loosen. Check
their tightness at least twice a year.
Clean the fan regularly to maintain its original appearance. Do not use water
to clean the fan as it may damage the motor or materials it is made of, or
even an electric shock. Use only a brush with fine bristles or a micro fibre
cloth to avoid scratching the surface of the fan.
Note : Failure to follow the maintenance instructions may void the
warranty.
Warranty
The warranty covers serious problems that may occur, but not minor deviations,
such as moderate amount of noise produced by the appliance, as each electrical
appliance produces a certain amount of noise.
Using the fan with loose screws or blades damaged by improper cleaning may
result in swaying or excessive noise that cannot be covered by the warranty.
Regular care will prevent similar problems.
Control
Using remote controls other than those supplied, using wall switches or
dimmers can damage the fan electronics and its motor. In this case, the
warranty becomes void.
Installation
This fan must be installed only by a qualified electrician. Incorrectly
installed fan can be dangerous to people in its vicinity and expensive to
repair. In this case, the warranty becomes void. This fan has been designed
for indoor use with the exception of rooms with high humidity, such as
bathrooms, swimming pools and the like. The manufacturer disclaims any
liability in the event of personal injury or property damage due to
incorrectly installed fan or its improper use. In case of any doubts, contact
a qualified electrician.
Increased perception of noise at night
The warranty does not cover the fact that during the night, when the ambient
sounds are normally suppressed during the day, the fan is more audible. In
addition, during the night, there may be fluctuations in the power supply,
which may be reflected in noise of the fan. This is not a sign of damage or
malfunction of the fan.
Troubleshooting
Before contacting professional service, consult the following list. It may save your time and money. This list includes common cases that are not the result of a defect in workmanship or in materials.
Problem | Possible cause | Solution |
---|
The fan does not rotate. (Note: Some steps will require a qualified
electrician.)| Blown fuses| Check the fuses and your household electrical
circuit.
Incorrectly tightened connections of the conductors| Check the connection.
This step must be performed by a qualified electrician.
The remote control is not working| Change the batteries in the remote control
or check their polarity.
No power supply| Check that the electricity is supplied to the fan.
Noisy operation| Loose screws| Tighten the screws carefully
Loose mounting bracket| Tighten all the screws
Incorrect remote control of the fan| Use only the remote control supplied by
the manufacturer
Mechanical noise| When turning the fan on for the first time, let it run
for at least 8 hours, all parts should settle to their position and the noise
should stop. If not, contact a service centre.
The lighting does not turn on| Damaged lighting| Contact a service
centre.
The fan rotates, but the airflow is insufficient| There are objects in
close proximity to the fan.| The objects in the room may be restricting the
airflow.
Improper fan blade diameter| The selected fan is too small in diameter given
the size of the room where it was installed.
Read the user manual. Read the corresponding section in this user manual before any use.
For certified services, an on-demand service manual is available.
This product must not be disposed of at the end of its life with other household waste, but must be delivered at a collection point for the recycling of waste electrical and electronic equipment. Batteries and accumulators do not belong to household waste, but within the European Union, under the Directive 2006/66/EC of the European Parliament and Council of 6 September 2006 on batteries and accumulators, they must be appropriately disposed of with respect to the environment. Please, dispose of the batteries in accordance with applicable local regulations. Batteries intended for disposal in collection points must be completely depleted, or short-circuit must be prevented (for instance, by taping contacts with adhesive tape).
The product complies with applicable European and other directives.
References
- Stropní ventilátory, mobilní klimatizace, odvlhčovače vzduchu, čističky vzduchu, zvlhčovače vzduchu | Gavri.cz
- Stropní ventilátory, mobilní klimatizace, odvlhčovače vzduchu, čističky vzduchu, zvlhčovače vzduchu | Gavri.cz
- Gavri.es | Ventiladores de techo | Deshumidificadores, humidificadores y purificadores
- Gavri.es | Ventiladores de techo | Deshumidificadores, humidificadores y purificadores