Insane Audio IACAM1 Universal Waterproof Camera User Manual

Insane Audio IACAM1 Universal Waterproof Camera

IACAMl
IACAMl is a universal, rugged, waterproof camera that can be mounted as a front or rear facing camera.
Installation is fairly straightforward. However, if you are not entirely sure how to properly install this item, we highly recommend consulting a professional installation technician.
If you need any additional information or technical assista nee, feel free to reach out to us anytime, at: support@insaneaudio.com
Enjoy your new camera and we’ll see ‘ya on the trails!

MOUNTING OPTIONS
IACAMl can be mounted just about anywhere you’d like and can be used as either a front facing camera or as a reverse camera. Either way, we recommend placing the camera in your desired location first then check the viewing angle on your screen before permanently mounting.

INSTALLING AS A BACKUP CAM

1. Place the camera in the desired location.
2. Power your camera from the RockCam Power Out and ground wires on the accessory pigtail. These wires can support up to two cameras.
3. Run the video extension cable from your IACAMl to the CAM IN port.
4. Seal all connections with waterproof tape or wire connectors.
5. Test your camera by placing your vehicle in reverse, adjust the viewing angle as necessary. Mount camera to vehicle when proper angle is reached.

INSTALLING AS A FRONT CAMERA

1. Place the camera in the desired location.
2. Power your camera from the Rock Cam Power Out and ground wires on the accessory pigtail.
3. Run the video extension cable from your IACAMl to the RockCam Video In port.
4. Seal all connections with waterproof tape or wire connectors.

You can access your front camera through the RockCam app.

PROGRAMMING IACAMl

Insane Audio’s IACAMl has a single push button switch that enables you to program certain core features of the camera to support different vehicle applications.
The switch modes are based on continuous button press times. You first need to enter the desired programming mode, then you can toggle options.
To enter a desired programming mode, press the button continuously in 0.5 sec intervals after the button is depressed.
After the camera goes into a specific mode, you can toggle features by pressing the button again between 0.5 and 3 sec. After 3 sec, the camera will return to default mode.
You may revert to factory settings by holding down the button for 3 sec.

IACAMl PROGRAMMING MODES

1. Turn on/off guide lines (default mode)
2. Image upside down/left and right reversal
3. Image system NTSC/PAL shift
4. Guide line selections
5. Guide line narrows and widens
6. Guide line shift up and down

TROUBLESHOOTING FOR REVERSE CAMERA APPLICATIONS

Once everything is properly connected, if you place your vehicle in reverse and you see a “No Signal” warning, then that means that you aren’t getting a clear signal to the CAM IN port. Be sure to double-check that your power and video connections are solid.

SPECIFICATIONS

• Image sensor
  l/4″ color CMOS

• TV system
  PAL/NTSC

• Effective pixels
  628 X 586

• Sensor size
  5.78mm x 4.79mm

• Resolution
  480TVL
  Minimum Illumination
  0.3LUX/Fl.2

• Lens
  3.6m m/2.8m m/l.8m m

• SNR ratio
  48d B (AGC-OFF)

• Electronic Shutter
  l/50 – l/70000 sec

• Video Output
  RCA connector

• Viewing Angle
  770°

• Maximum Current
  750 mA

• Power Supply
  9-24 VDC

• Operating Temperature -22°F – 722°F, RH 95%

• Storage Temperature
  -30°F – 750°F, RH 95% Max

• Weight
  700g

• Other Function AWB, AGC, BLC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>