Insane Audio JK4001 Multimedia Head Unit User Manual
- June 3, 2024
- iNSANe AUDIO
Table of Contents
Insane Audio JK4001 Multimedia Head Unit
Safety Precautions
Before you use this product, be sure to carefully read this Installation
Manual and the separate User’s Guide to ensure product is installed and used
properly. Insane Audio is not responsible for any problems that arise as a
result of failure to follow the instructions provided.
This manual includes a number of symbols that are intended to help you use the
product safely, to prevent harm to you, others and protect against any
property damage. These symbols and their meanings are listed below. Make sure
you fully understand these symbols before you begin the installation.
Disconnect the negative battery terminal before beginning installation.
Explanations of Injury and Damage That May Result from Incorrect Use
WARNING
Ignoring the content marked by this indication and using the product
incorrectly is expected to lead to death or serious injury.
CAUTION
Ignoring the content marked by this indication and using the product
incorrectly is expected to lead to death or serious injury.
Warnings
- Do not unassembled or modify the product. Doing so could lead to an accident, fire or electrical shock.
- Store screws and other small objects where children cannot reach them. If a small object is swallowed, consult with a doctor immediately.
- When replacing fuses be sure to use the fuses with the specified current rating. Failing to do so could lead to an accident or fire. Only connect the product to a 12V DC negative ground car. Failing to do so could lead to an accident or fire.
- Since this vehicle has two batteries, disconnecting the battery is not a good option. Take caution when testing circuits. Failing to do so could lead to electric shock or injury.
- Do not cut the insulation on a cord and take power from another device. Doing so could lead to fire or electric shock.
- Do not install the product in a location where it will obstruct the drivers forward view; interfere with the operation of the steering wheel, gear shift, or the like; or pose a threat to passengers. Doing so could lead to an accident or injury.
- When making a hole in the vehicle body, be careful to avoid damaging pipes, the fuel tank, electrical wiring, and the like. This kind of damage could lead to an accident or fire.
- When installing and grounding the product, do not use any of the bolts or nuts of the steering wheel, brakes, fuel tank, or the like. Doing so could make the brakes stop working or could lead to fire.
- Do not install the product near the passenger-side airbag. Doing so could interfere with the operation of the airbag and lead to an accident or injury.
- Bundle cords so that they don’t interfere with driving. Wrapping cords around the steering wheel, gearshift, brake pedal, or the like could lead to an accident or damage equipment.
Caution
- Connect the product properly according to the instructions. Failing to do so could lead to fire or an accident.
- Do not sandwich cords between the seat railing or allow them to touch protrusions. Resulting breaks or shorts could lead to electric shock or fire.
- Do not block vents or heat sinks. Doing so could lead to fire or damage equipment.
- Use the accessories according to the instructions, and attach them securely. Failing to do so could lead to an accident or damage equipment.
- Do not install the product where it may be exposed to water or in a place with high levels of humidity or dust. Doing so could lead to fire or damage equipment.
Introduction
Congratulations on purchasing the JK4001. This manual is intended to give instructions for installation.
PLEASE USE YOUR NEW JK4001 RESPONSIBLY. Never attempt to operate the unit or view videos while driving. While driving, always keep both hands on the wheel and your eyes on the road.
Should you run into problems or need any additional assistance, feel free to e-mail us at support@insaneaudio.com or scan the QR code below.
Once you get your JK4001 installed, a helpful document is our Quick Start Guide which will walk you through the user interface.
Enjoy your new JK4001 and we’II see ya’ on the trail!
SCAN ME
Parts List
- Main Wiring Harness
- Audio RCA Wire Harness
- External Microphone
- RockCam Camera Harness
- GPS Antenna
- USB Wire Harness
- USB Wire Harness
- USB Wire Harness
- OBDII Adapter
- IA CarPlay/Android Auto Wire Harness
- WIFI and Bluetooth Antenna
Opening the Dashboard
Note: Disconnect the negative battery terminal before beginning this installation.
- On the top of your dash, there is a rubber insert that can be pried open with a plastic dash tool or a small screwdriver. That will reveal a single 7mm bolt that needs to be removed.
- Next, pry open the center switch panel. Be careful not to scratch the plastic.
- Remove the single 7mm bolt behind the switch panel.
- Pry off the dash panel just below the steering wheel. Start with the top corners. Once it is off, remove two 7mm bolts at the top corners.
- Now you can pop the entire upper dash panel off. It’s held in place with pressure clips.
- Remove the upper dashboard.
Removing OEM Head Unit
There are four 7mm bolts on the face of your stock radio that need to be removed then the whole thing will slide out. Disconnect the antenna and the old wiring harness from the factory harness.
The factory AM/FM antenna adapter is a white connector that can easily be removed by pressing the little lever down. This plugs right into the back of the JK4001. The yellow connector is a SiriusXM antenna that is no longer used .
uConnect Modules
CAUTION
SPECIAL NOTE FOR VEHICLES THAT PREVIOUSLY HAD OEM uCONNECT MODULES
Certain uConnect modules will still remain active even after your OEM radio has been removed. This may result in the uConnect module placing an un- necessary drain on your vehicle’s battery even after your Jeep is powered off.
To remove your uConnect module:
- With your dash still opened up, remove your AC controls (they are on pressure clips).
- You should see the old uConnect module (two screws hold it in place).
- Unplug it and remove it.
Installing the JK4001
NOTE: FOR VEHICLES THAT HAVE THE ALPINE PREMIUM SOUND SYSTEM
CAUTION
Before proceeding with the installation, vehicles with the OEM Alpine Premium
Sound System will need to make a minor change on the main wiring harness.
NOTE: If your vehicle is not equipped with the OEM Alpine Premium Sound System or if you are using your own aftermarket amps and speakers you do not have to make any changes. F2 should be connected to F1 and R2 should be connected to R1 as shown in picture.
For OEM Alpine Premium Sound System:
If you DO have the OEM Alpine Premium Sound System, you will need to swap the
speaker quick connect wires shown in the picture.
Connect F2 to R1 and R2 to F1.
JK4001 Wire Diagram
- (A) Connect the main power wire harness
- (B) Connect Audio RCA wire harness for aftermarket amps and speakers only, not needed for OEM sound system
- (C) Connect USB Fast Charge harness
- (D) Connect IA Carplay/Android Auto wire harness
- (E) Connect RockCam wire harness for camera connections
- (F) Connect USB wire harness
- (H) Connect Insane TV wire harness (Insane TV module needed)
- (I) Connect WiFi antenna
- (J) Connect Bluetooth antenna
- (K) Connect GPS antenna
- (L) Connect External Microphone
- (M) Connect Digital Optical Output (Optional)
- (N) Connect AM/FM Radio antenna
USB Wiring Harnesses
Route all USB wires to the glove box
GPS Antenna
The GPS antenna has a magnetic or an adhesive mount and is best placed on the
top of the head unit as shown in the picture.
External Microphone
The JK4001 comes with a built-in Bluetooth microphone, but we also include a
high quality external microphone. This external microphone will work at just
about any location, but we do have some recommendations for placement. Try to
keep this microphone away from any windows, air vents, or speakers to avoid
background sounds or feedback. The external mic will plug into the back of the
head unit via a 3.5mm headphone jack plug.
Cameras
The JK4001 is designed to automatically display a backup camera anytime your
vehicle is in reverse.
Connect your camera(s) to the RockCam video RCA pigtail. We support up to 4 cameras. The pigtail offers two wires labeled “RockCam Power” and “RockCam GND” that automatically provide +12V whenever you reverse the vehicle or open the RockCam app. We recommend you use these wires to power your cameras.
Note: Before
making any connections, unplug the pigtail from the head unit and make sure
that everything is powered off.
Note: If you have a manual transmission in your Jeep and your camera is
not activating when in reverse, you may have to perform an additional step.
WARNING
Camera activation is controlled by the CAN bus module, and manual transmission Jeeps often have a different set of CANcodes that can change how the cameras are controlled. Run a wire from your reverse lights and splice directly to the head-unit side of the orange reverse trigger wire, as shown in picture. This will activate your rear camera whenever you put your vehicle in reverse.
Cameras
Check the camera installation by opening the RockCam app.
Tips
If you see a “No signal” warning, ensure that the front video feed is
connected to “RockCam Video In” RCA port and the power wires are properly
connected.
With the RockCam app, you can even view any camera installed. Tap on the lower camera pallet at the bottom of the screen to switch between front, rear and side views whenever you’re parked or in motion.
Operational Tips
Insane Navigation System
Insane NavEngine can be accessed both via the icon or by pressing the
navigation button on the face of your JK4001. The GPS card is located behind
the cover labeled “GPS/SD Card”. The GPS card needs to be inserted while using
the Insane Navigation System. This will get you where you’re going both on and
off the road.
MicroSd Card
The JK4001 comes with an additional microSD card slot located behind the cover
labeled “GPS/SD Card”. Load up a microSD card with movies or music and access
the content via the VIDEO or MUSIC applications. All MicroSd Cards above 32GB
should be formatted to NTFS; below 32 GB should be formatted to FAT32.
OBDII Adapter
The JK4001 comes with an OBDII Bluetooth adapter and the Torque application
already installed. Please refer to the Quick Start Guide for instructions on
how to set this up for the first time.
Troubleshooting
GENERAL
Head unit not powering ON, no lights, no screen.
Check and reseat your main wiring harness. Remove the black wiring harness
plug from the rear of the head unit and confirm that non of the pins are bent,
pushed in, or otherwise damaged. Check that there are no loose or disconnected
wires. Reconnect it, ensuring the plug is inserted evenly and firmly into the
back of the head unit. Perform the same check on the grey OEM harness plug.
Unplug it, and check for any bent or damaged pins or loose wires, and
reconnect it evenly and firmly.
It’s important to note that when working with Wiring Harnesses, you should
never pull on the wires themselves. Every harness has a clip that needs to be
depressed and you should only push/pull on the plastic harness itself.
Rebooting the head unit.
To perform a System Reset, open the GPS/SD card cover, the Reset button is
located in the top left corner above the GPS card slot. There is a small hole
with a button inside it. Use a pen or paperclip to press the button until it
clicks, and then release it. This will power down the Head Unit and complete a
full reboot without you having to disconnect the battery. Be sure not to
confuse the Reset button with the internal microphone, which is labeled “MIC”
located on the front of the Head Unit.
BLUETOOTH
Device is not pairing.
Make sure Bluetooth is turned ON: Apps > Settings > Bluetooth > ON. Make sure
that you are connecting from your phone to the head unit (not the other way
around). Open the Bluetooth application (BT) and delete all Bluetooth pairings
you have currently and re-pair your device to the Head Unit.
AM/FM Radio
Poor AM/FM Reception
Make sure OEM AM/FM antenna (white) is firmly connected to the AM/FM connector
located on the back of the Head Unit. Please be sure not to confuse OEM AM/FM
Antenna (white) with satellite radio antenna or any other wires. Some vehicles
manufactures mays use extension cables or couplers to extend the factory
antenna inside of the dashboard, please be sure to check all connections from
the Head Unit to the factory antenna.
Apple CarPlay
Apple CarPlay will not Start/Launch
Ensure a certified Apple cable is being used. Make sure Apple CarPlay is
enabled on the phone. Ensure the phone is plugged into IA CarPlay USB wire.
Check IA CarPlay USB wire connection located in the back of the Head Unit.
Android Auto
Android Auto will not launch/start.
Ensure a certified Android cable is being used. Make sure Android Auto
application has been downloaded and installed on the phone. Ensure the phone
is plugged into IA CarPlay USB wire. Check IA CarPlay USB wire connection
located in the back of the Head Unit.
Cameras
No signal.
Make sure the camera RCA is plugged into the correct input labeled “Backup
Cam” on the RockCam video RCA pigtail. Ensure the camera is connected to the
“RockCam Power and GND” wires. Confirm that the reverse trigger wire is
connected to a source that is receiving 12V when the vehicle is in reverse
(Backup cameras only).
Resources
Insane Audio offers free lifetime support. If you have any questions and/or concerns regarding your head unit, feel free to reach out to us at support@insaneaudio.com.
We recommend you review the 4000 Series Quick Start Guide and tutorial videos, which can be found on the Support section of our website.
Note: Please register your head unit on the Support section of our website to receive warranty benefits.
SCAN ME
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>