IA JL4001 Insane Audio Instruction Manual
- June 4, 2024
- iNSANe AUDIO
Table of Contents
JL4001 Insane Audio
Caption
JL4001
Installation Manual
Safety Precautions
Before you use this product, be sure to carefully read this Installation
Manual and the separate User’s Guide to ensure product is installed and used
properly. Insane Audio is not responsible for any problems that arise as a
result of failure to follow the instructions provided.
This manual includes a number of symbols that are intended to help you use the product safely, to prevent harm to you, others and protect against any property damage. These symbols and their meanings are listed below. Make sure you fully understand these symbols before you begin the installation.
Disconnect the negative battery terminal before beginning installation.
Explanations of Injury and Damage That May
Result from Incorrect Use
WARNING
Ignoring the content marked by this indication and using the product incorrectly is expected to lead to death or serious injury.
CAUTION
Ignoring the content marked by this indication and using the product incorrectly is expected to lead to death or serious injury.
Warnings
Do not unassemble or modify the product. Doing so could lead to an accident,
fire or electrical shock.
Store screws and other small objects where children cannot reach them. If a small object is swallowed, consult with a doctor immediately.
When replacing fuses be sure to use the fuses with the specified current rating. Failing to do so could lead to an accident or fire. Only connect the product to a 12V DC negative ground car. Failing to do so could lead to an accident or fire.
Since this vehicle has two batteries, disconnecting the battery is not a good option. Take caution when testing circuits. Failing to do so could lead to electric shock or injury.
Do not cut the insulation on a cord and take power from another device. Doing so could lead to fire or electric shock.
Do not install the product in a location where it will obstruct the driver?s forward view; interfere with the operation of the steering wheel, gear shift, or the like; or pose a threat to passengers. Doing so could lead to an accident or injury.
When making a hole in the vehicle body, be careful to avoid damaging pipes, the fuel tank, electrical wiring, and the like. This kind of damage could lead to an accident or fire.
When installing and grounding the product, do not use any of the bolts or nuts of the steering wheel, brakes, fuel tank, or the like. Doing so could make the brakes stop working or could lead to fire.
Warnings
Do not install the product near the passenger-side airbag. Doing so could
interfere with the operation of the airbag and lead to an accident or injury.
Bundle cords so that they don’t interfere with driving. Wrapping cords around the steering wheel, gearshift, brake pedal, or the like could lead to an accident or damage equipment.
Caution
Connect the product properly according to the instructions. Failing to do so
could lead to fire or an accident.
Do not sandwich cords between the seat railing or allow them to touch protrusions. Resulting breaks or shorts could lead to electric shock or fire.
Do not block vents or heat sinks. Doing so could lead to fire or damage equipment.
Use the accessories according to the instructions, and attach them securely. Failing to do so could lead to an accident or damage equipment.
Do not install the product where it may be exposed to water or in a place with high levels of humidity or dust. Doing so could lead to fire or damage equipment.
Introduction
Congratulations on purchasing the JL4001. This manual is intended to give
instructions for installation.
PLEASE USE YOUR NEW JL4001 RESPONSIBLY. Never attempt to operate the unit or
view videos while driving. While driving, always keep both hands on the wheel
and your eyes on the road!
Should you run into problems or need any additional assistance, feel free to
drop us an e-mail at support@insaneaudio.com or scan the QR code below. Once
you get your JL4001 installed, a helpful document is our Quick Start Guide
which will walk you through the user interface.
Enjoy your new JL4001 and we’II see ya’ on the trail!
SCAN ME
Parts List
A
B C
K A Main Wiring Harness
B Audio RCA Wire Harness
C External Microphone
D RockCam Camera Harness
E GPS Antenna
D
E J
JL4001
F G H
I
F USB Wire Harness
G USB Wire Harness
H USB Wire Harness
I OBDII Adapter
J IA CarPlay/Android Auto Wire Harness
K One Bluetooth & One WiFi Antenna
Opening the Dashboard
1
As a precautionary measure it’s a good idea to mask out the dashboard and
panels to prevent scratches.
2
Unsnap the 6 clips and remove the Knee Panel under the Steering Wheel using a
Panel Removal Tool.
Opening the Dashboard
3
Unsnap the 10 clips, unplug the 2 harnesses, and remove the HVAC panel using a
Panel Removal Tool.
4
Use the #2 Phillips Screwdriver to extract the (2) screws from the bottom of
the Radio Bezel.
Opening the Dashboard
5
Unsnap the 6 clips and remove the Radio Bezel using a Panel Removal Tool.
NOTE: Use the two clips from OEM Radio Bezel for the JL4001 frame.
6
Use the #2 Phillips Screwdriver to extract the (4) screws from Head Unit.
Disconnect and remove the Radio.
Removing OEM Head Unit
7
Disconnect the OEM Power Harness, SiriusXM Radio Antenna connector (yellow),
rear OEM Factory Camera Wire Connector (red), OEM AUX Input Connector (gray)
from behind the OEM Head Unit.
8
The disconnected harness and wires from the previous step will be used later
to connect to the main harness in the installation. The yellow connector is a
SiriusXM Antenna that is no longer used.
Installing the JL4001
9
At the radio cavity, connect the Main Harness, the white OEM AM/FM Antenna,
and any other USB and/or A/V Wire Harnesses and secure them. Connect the red
OEM Rear Camera Wire to the Black Camera Module Box located on the JL4001 Main
Power Wire Harness and make sure it is secure.
Camera Module Box
10
OEM AM/FM Radio Antenna
At the radio cavity, connect the Bluetooth, WiFi and GPS Antennas and make sure they are secure.
Bluetooth, WiFi and GPS Terminals
AM/FM Radio Connector
AM/FM Connector
Installing the JL4001
CAUTION
NOTE: FOR VEHICLES THAT HAVE THE ALPINE PREMIUM SOUND SYSTEM
Before proceeding with the installation, vehicles with the OEM Alpine Premium Sound System will need to make a minor change on the Main Wiring Harness.
NOTE: If your vehicle is not equipped with the OEM Alpine Premium Sound System or if you are using your own aftermarket amps and speakers you do not have to make any changes. F2 should be connected to F1 and R2 should be connected to R1 as shown in picture.
For OEM Alpine Premium Sound System:
If you DO have the OEM Alpine Premium Sound System, you will need to swap the
speaker quick connect wires shown in the picture. Connect F2 to R1 and R2 to
F1.
F2 – F1 Connection (Labeled) R2 – R1 Connection (Labeled)
Main Power Wire Harness
JL4001 Wiring Diagram
I
J
K
LM N
(A) Connect the main power wire harness (B) Connect Audio RCA wire harness for aftermarket amps and speakers only, not needed for OEM sound system (C) Connect USB Fast Charge harness (D) Connect IA Carplay/Android Auto wire harness (E) Connect RockCam wire harness for camera connections (F) Connect USB wire harness and OEM AUX input wire (gray) (H) Connect Insane TV wire harness (Insane TV module needed) (I) Connect WiFi antenna (J) Connect Bluetooth antenna (K) Connect GPS antenna (L) Connect External Microphone (M) Connect Digital Optical Output (Optional) (N) Connect AM/FM Radio antenna
Installing the JL4001
USB Wiring Harnesses
Route all USB wires to the glove box.
GPS Antenna
Place adhesive GPS antenna behind the dashboard on top of the vent on the driver’s side of the vehicle.
The GPS antenna has an adhesive mount and is best placed behind the dashboard on top of the vent on the driver’s side of the vehicle.
Main Power Wire Harness
Installing the JL4001
External Microphone
The JL4001 comes with a built-in Bluetooth microphone, but we also include a
high quality external microphone. This external microphone will work at just
about any location, but we do have some recommendations for placement. Try to
keep this microphone away from any windows, air vents, or speakers to avoid
background sounds or feedback. The external mic will plug into the back of the
head unit via a 3.5mm headphone jack plug.
Cameras
Your JL4001 is designed to automatically display a backup camera anytime your
vehicle is in reverse, See Step 7.
Installing the JL4001
Cameras
Connect additional camera(s) to the RockCam video RCA pigtail. We support up to 4 cameras. The pigtail offers two wires labeled “RockCam Power” and “RockCam GND” that automatically provide +12V whenever you reverse the vehicle or open the RockCam app. We recommend you use these wires to power your cameras.
RockCam Power and GND wires
Note: Before making any connections, unplug the pigtail from the Head Unit and make sure that everything is powered off.
WARNING
Note: If you have a manual transmission in your Jeep and your camera is not activating when in reverse, you may have to perform an additional step.
Camera activation is controlled by the CAN bus module, and manual transmission Jeeps often have a different set of CANcodes that can change how the cameras are controlled. Run a wire from your reverse lights and splice directly to the head-unit side of the orange reverse trigger wire, as shown in picture. This will activate your rear camera whenever you put your vehicle in reverse.
ORANGE wire labeled “Reverse Trigger”
Installing the JL4001
Cameras
Check the camera installation by opening the RockCam app.
Tips
If you see a “No signal” warning, ensure that the front video feed is
connected to “RockCam Video In” RCA port and the power wires are properly
connected. With the RockCam app, you can even view any camera installed. Tap
on the lower camera pallet at the bottom of the screen to switch between
front, rear and side views whenever you’re parked or in motion.
Operational Tips
Insane Navigation System
Insane NavEngine can be accessed both via the icon or by pressing the
navigation button on the face of your JL4001. The GPS card is located behind
the cover labeled “GPS/SD Card”. The GPS card needs to be inserted while using
the Insane Navigation System. This will get you where you’re going both on and
off the road.
MicroSd Card
The JL4001 comes with an additional microSD card slot located behind the cover
labeled “GPS/SD Card”. Load up a microSD card with movies or music and access
the content via the VIDEO or MUSIC applications. All MicroSd Cards above 32GB
should be formatted to NTFS; below 32 GB should be formatted to FAT32.
OBDII Adapter
The JL4001 comes with an OBDII Bluetooth adapter and the Torque application
already installed. Please refer to the Quick Start Guide for instructions on
how to set this up for the first time.
Troubleshooting
GENERAL
BLUETOOTH
Head unit not powering ON, no lights, no screen.
Check and reseat your Main Wiring Harness. Remove the black Wiring Harness
plug from the rear of the Head Unit and confirm that none of the pins are
bent, pushed in, or otherwise damaged. Check that there are no loose or
disconnected wires. Reconnect it, ensuring the plug is inserted evenly and
firmly into the back of the head unit. Perform the same check on the grey OEM
Harness Plug. Unplug it, check for any bent or damaged pins or loose wires,
and reconnect evenly and firmly.
It’s important to note that when working with wiring harnesses, you should never pull on the wires themselves. Every harness has a clip that needs to be depressed and you should only push/pull on the plastic harness itself.
Rebooting the head unit.
To o a system reset, open the GPS/SD card cover, the reset button is located
in the top left corner above the GPS card slot. There is a small hole with a
button inside it. Use a pen or paperclip to press the button until it clicks,
and then release it. This will power down the head unit and complete a full
reboot without having to disconnect the battery. Be sure not to confuse the
reset button with the internal microphone, which is labeled “MIC” located on
the front of there head unit.
Device is not pairing.
Make sure Bluetooth is turned ON: Apps > Settings > Bluetooth > ON. Make sure
that you are connecting from your phone to the head unit (not the other way
around). Open the Bluetooth application (BT) and delete all Bluetooth pairings
you have currently and re-pair your device to the head unit.
AM/FM Radio
Poor AM/FM Reception
Make sure OEM AM/FM antenna (white) is firmly connected to the AM/FM connector
located on the back of the head unit. Please be sure not to confuse OEM AM/FM
antenna (white) with satellite radio antenna or any other wires. Some vehicles
manufactures mays use extension cables or couplers to extend the factory
antenna inside of the dashboard, please be sure to check all connections from
the head unit to the factory antenna.
Apple CarPlay
Apple CarPlay will not Start/Launch
Ensure a certified Apple cable is being used. Make sure Apple CarPlay is
enabled on the phone. Ensure the phone is plugged into IA CarPlay USB wire.
Check IA CarPlay USB wire connection located in the back of the head unit.
Troubleshooting
Resources
Android Auto
Android Auto will not launch/start.
Ensure a certified Android cable is being used. Make sure Android Auto
application has been downloaded and installed on the phone. Ensure the phone
is plugged into IA CarPlay USB wire. Check IA CarPlay USB wire connection
located in the back of the head unit.
Insane Audio offers free lifetime support. If you have any questions and/or concerns regarding your head unit, feel free to reach out to us at support@insaneaudio.com.
We recommend you review the 4000 Series Quick Start Guide and tutorial videos, which can be found on the Support section of our website.
Cameras
Note: Please register your head unit on the Support section of our website to receive warranty benefits.
No signal.
Make sure the camera RCA s plugged into the correct input labeled “Backup Cam”
on the RockCam video RCA pigtail. Ensure the camera is connected to the
“RockCam Power and GND” wires. Confirm that the reverse trigger wire is
connected to a source that is receiving 12V when the vehicle is in reverse
(Backup cameras only).
SCAN ME