Lifeplus SFP201A Electric Fireplace Infrared Stove Heater User Guide
- June 2, 2024
- Lifeplus
Table of Contents
STOVE STYLE FIREPLACE HEATER
SFP201A
PRODUCT USE GUIDE
INTRODUCTION
Thank you for choosing a LIFE PLUS heater. This owner’s manual will provide
you with valuable information necessary for the proper care and maintenance of
your new product. Please take a few minutes to read it.
Please be free to EMAIL Us
service@llifepluspro.com
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precaution Should always be followed to reduce the risk of fire, electric shock and injury to person, including the following:
- Read all instructions before using this heater/fan.
- This heater/fan is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use provided handle when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least o.9 meters from the front of the heater-fan and keep them away from the sides and rear.
- Do not use heater unattended. Use of extreme caution is necessary when any heater is used by or near children, invalids, disabled persons or pets.
- Do not operate the heater with a damaged power cord or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment or repair.
- Do not use heater outdoors.
- Use your heater only in dry environments. This heater is not intended for use in a bathroom, laundry area, or similar locations, or near sinks, washing machines, swimming pools or other sources of water. Never locate heater where it may fall into a bathtub or other water container. Do not use in damp environments such as flooded basements.
- Do not place the heater on a small, unlevel, uneven or any surface which might allow heater to tip or fall.
- For proper operation, heater should be placed on a smooth, non-combustible surface. Do not place on rugs, carpet, vinyl flooring or other plastic surfaces. Not for use outdoors or in wet areas.
- This heater is not designed as a primary heat source.
WARNING
- Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
- Always unplug heater when not in use.
- Do not run power cord under carpeting. Do not cover cord with throw rugs, runners or similar coverings. Arrange cord away from traffic area where it will not be tripped over.
- To disconnect heater, turn controls off then remove plug from outlet.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the heater.
- To prevent a possible fire, do not block air intakes or exhaust in any manner.
- Do not use on soft surfaces like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored.
- Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons or property.
TECHNICAL PARAMETERS:
| Model No. | SFP201A |
|---|---|
| Item Name | Stove Style Fireplace Heater |
| Rated Voltage | 120V(60Hz) |
| Rated Power | 1500W |
Two Setting
Safy Protection| Low/High
Safety thermal cut-off device
Heating Element
Net Weight| Heating wire
6.72 lbs
Product Size| 16.22×9.76×17.95 inch
IMPORTANT SAFETY FEATURES
The heater is equipped with an automatic overheat protection device located inside the body of the heater. If the heater grille is obstructed, or if the heater gets too hot for any reason, the automatic overheat protection device will turn the heater off. To reset the heater, simply turn power off and unplug the heater for 10 minutes until it cools down and you may plug the heater in and restart the heater. Be sure that the heater is on a smooth level surface with no obstructions.
PRODUCT DIAGRAM
LEG ASSEMBLY
Simple assembly is required if the legs of your heater arrive unassembled
Using a screwdriver, thread three screws through the holes in each leg as
illustrated in Fig.1 below and tighten them down counter-clockwise onto the
underside of the heater.
PLEASE NOTE : Extra screws are provided, you may have some left over
after assembly.
INSTRUCTIONS FOR USE
-
HEATER OPERATION: Always operate the heater in the upright position following all instructions and recommendations listed in this manual.
HEATER LOCATION: Place the heater in the area of the room that is coldest.
HEATER CONNECTION: Plug heater directly. -
Into 120 volt A.G., 60Hz wall outlet. Be sure plug fits tightly in outlet. A loose connection may cause overheating and damage to the plug or heater.
NOTE: To prevent overloading a circuit, do not plug the heater into a circuit that is servicing other electrical needs.
TURNING HEATER ON
- For Flame Effect Only- Slide main power ON/OFF switch to ON position to have the flame effect without any heater functions.
- For Low Heat-Slide main power ON/OFF switch to ON position and Slide switch “I” to ON position.
- For High Heat-Slide main power ON/OFF switch to ON position and slide both switch “I” and switch “II” to ON position.
SETTING THERMOSTAT
After heater has been turned on and the room has reached the desired
temperature, slowly rotate the thermostat knob counter-clockwise until the
heater shuts off (you should hear a faint “click”) By leaving the thermostat
at the setting it will automatically maintain this temperature. To lower the
temperature, rotate the knob further counter-clockwise towards the LOW(left)
position. To raise the temperature, rotate the thermostat knob clockwise
towards the HIGH(right) position.
TURNING OFF:
Turn the Main Power On/Off power switch OFF to discontinue use. The Low Heat
Switch and High Heat Switch can remain in any position and will have no power.
They will continue to have the same set functions when the heater is turned
back on. Heater should be unplugged when not in use.
CARE AND MAINTENANCE
CLEANING: CAUTION-Before cleaning the heater be sure to disconnect power
cord and allow the heater to cool completely. Clean the outside surface with a
clean damp cloth. Do not use harsh chemical or abrasive cleaners. DO NOT
IMMERSE THE HEATER IN WATER. Allow heater to dry completely before use. Use a
vacuum or duster to keep heat and vent area clean and free of dust and dirt.
REPAIR
Do not operate the heater without the grille in place. do not use the heater
if it has malfunctioned or become damaged in any way. Do not remove back cover
of heater; no serviceable parts.
WARRANTY
After-sales Service Letter of Commitment: All products purchased in our company are guaranteed to keep in good repair for 1 year. If quality problems happen in guarantee period, our company will maintain for free or provide replacement. Additionally, our company provides technical support and fittings for life. After-sales service isn’t restricted by time and hear feedback idea of users and deal with them in time. If you are caught in some problems when using our products, welcome to contact us at any time.
Things To Be Best With Life plus
E-mail: service@lifepluspro.co
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>