Rowenta Straightener Instruction Manual
- June 3, 2024
- Rowenta
Table of Contents
Rowenta Straightener Instruction
GENERAL DESCRIPTION
- A. Tongs
- B. Digital screen:
1. Temperature display of the plates
2. Temperature locked during use
3. Ready to use indicator: “READY”- C. -/+ button to reduce/increase temperature
- D. ON/OFF switch
- E. Smoothing plates with Ultrashine Nano Ceramic coating
- F. Rotating power cord outlet
- G. Power supply cord
- H. Lock System (to lock and unlock the tongs)
SAFETY INSTRUCTIONS
- For your safety, this appliance complies with the applicable standards and regulations (Low Voltage Directive, Electromagnetic Compatibility, Environmental…).
- The appliance’s accessories become very hot during use. Avoid contact with the skin. Make sure that the supply cord never comes into contact with the hot parts of the appliance.
- Check that the voltage of your electricity supply matches the voltage of your appliance. Any error when connecting the appliance can cause irreparable harm, not covered by the guarantee.
- As an additional safety measure, we recommend the installation of a residual current difference device in the electrical circuit supplying the bathroom,acting at not more than 30 mA.Ask your installer for advice.
- The installation of the appliance and its use must however comply with the standards in force in your country.
- Caution : Never use your appliance with wet hands or near water contained in bath tubs, showers, sinks or other contai-ners…
- When using the appliance in the bathroom, unplug it after use as the presence of water nearby may pose a danger even when the appliance is turned off.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of expe-rience and knowledge, unless they have been given supervision or ins-truction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
- If the supply cord is damaged, it must be replaced by the manufac-turer, its service agent or similarly qualified persons in order to avoid a hazard.
- Stop using your appliance and contact an Authorised Service Centre if:
- your appliance has fallen,
- it does not work correctly.
- The appliance must be unplugged:
- before cleaning and maintenance procedures.
- if it is not working correctly.
- as soon as you have finished using it.
- Do not use if the cord is damaged.
- Do not immerse or put under running water, even for cleaning pur-poses.
- Do not hold with damp hands.
- Do not hold the appliance by the casing, which is hot, but by the handle.
- Do not unplug by pulling on the cord, rather pull out by the plug.
- Do not use an electrical extension lead.
- Do not clean with abrasive or corrosive products.
- Do not use at temperatures below 0°C and above 35°C. GUARANTEE : This product has been designed for domestic use only. Any commercial use, inappropriate use or failure to comply with the instructions, the manufacturer accepts no responsibility and the gua-rantee will not apply.
BRINGING INTO SERVICE
Your appliance will heat up very quickly (60 seconds) and the temper-ature will remain stable throughout use. Handle with extreme caution as the end of the straightener may be very hot!
-
Plug in the appliance.
-
To open the tongs, press the “Lock System” button.
-
Set the ON / OFF switch to position I: temperature 120 will then ap-pear on the digital screen.
-
In less than 60 seconds: when the word “READY” appears on the digital screen, the appliance will be ready to use in the minimum tem-perature position (120°C).
-
Select the ideal temperature for your hair using the -/+ buttons: press the – button to reduce the temperature or the + button to in-crease it.
The digital screen will show the selected temperature. As soon as the appliance reaches the requested temperature, the word “READY” will appear. -
To turn the appliance off, set the ON / OFF switch to position 0.
-
After use: close the clamps, use the “Lock System”, unplug the appli-ance and leave it to cool down completely before putting it away.
Note: To avoid any handling error (inadvertently pressing the +/- but- tons during use) this appliance is equipped with a locking function. If you wish to lock your temperature setting during use, press the + or – button for 2 seconds. Your setting is being locked, a padlock ap-pears on the screen. If you wish to change your appliance’s temperature, you will need to unlock it by again pressing the + or – button for 2 seconds. Your set-ting is being unlocked, the padlock disappears from the screen. You can change the temperature by pressing the buttons +/-.
USE
Hair must be untangled, clean and dry.
-
Do not use the appliance on synthetic hair (wigs, extensions, etc.).
-
Form a small lock a few centimetres in width, comb it and place it between the plates.
Hold the hair firmly between the plates and slide the appliance slowly from the roots to the tip of the hair. -
The ceramic coating on the plates protects your hair against over-heating by uniformly spreading the heat.
-
Wait for the smoothed hair to cool down before styling. HAIRDRESSER’S TIPS
-
Always start by smoothing the locks underneath. Work from the back of the neck first before going onto the side of the head and finish with the front.
-
To avoid streaks along the lengths, work using a smooth and uninterrupted movement.
-
To highlight, apply hair setting lotion before smoothing.
MAINTENANCE
CAUTION! Always unplug your appliance and allow it to cool before cleaning it.
- To clean the appliance, unplug it and then wipe with a damp cloth and dry with a dry cloth.
ENVIRONMENT PROTECTION FIRST!
Your appliance contains valuable materials which can be recovered or recycled.
Leave it at a local civic waste collection point.