MedicGrow TSC-2 Master Controller User Manual
- June 3, 2024
- MedicGrow
Table of Contents
TSC-2 Master Controller
User Manual
Master Controller
TSC-2 Master Controller
TSC-2
LED GROW LIGHT
USER MANUAL
IMPORTANT PRODUCT INFORMATION
- Please read this manual thoroughly before attempting to install or operate our LED products.
- After successful installation and configuration of the system, be sure to keep this manual in a safe place for future reference. Safety is a key component to a long-lasting and trouble-free installation.
- Use all our products only as directed. Failure to observe the following safety warnings may result in serious injury or death, and by law, will waive any and all liability for the manufacturer and resellers.
WARNINGS AND INSTRUCTIONS FOR USE:
Warning: To reduce the risk of electrical shock or serious injury,
always take the proper precautions and unplug the fixture before moving or
cleaning it.
Warning: In the event that the light bar becomes submerged, first
disengage the circuit breaker, then unplug the fixture before removing it from
the water.
Warning: Our LED grow lights are for indoor use only. Do not expose to
water drip or spray. Do not expose the lights to physical harm such as impact
or severe environmental conditions. The optimal operating temperature is
between 68°F-86°F/20°C -30°C.
Warning: When installing our LED grow lights, ensure that the power
outlets are properly grounded and have adequate capacity. If there is any
doubt, please consult an electrician. Please ensure that there is adequate
space for airflow around the lights. A minimum of 12 inches of space is
recommended above the light and 2 inches at the sides.
Wa r ning: To prevent eye damage, avoid looking directly at the lights
when they are on. Use shielding or light-blocking glasses to protect your
eyes.
Warning: Never place the fixture face down on a surface, as it may damage
the diodes.
Caution LED and heat sink surfaces may be hot. Allow sufficient cooling
time before handling.
Caution To reduce the risk of overheating, never place operating fixtures
face down on a flat surface. Always allow for adequate ventilation of fixtures
and power supplies.
Recommendation: We strongly encourage installing one or more surge
suppres-sors to protect your grow light(s). Power surges are one of the
leading causes of premature grow light failure.
OVERVIEW
Congratulations! You’ve just purchased the best full-spectrum LED grow light
the industry has ever seen.
Our high-performance LED grow lights are up to 50% more power-efficient than
HID technology.
Our light fixtures set a new standard for LED grow lighting.They are powerful
enough to serve as the primary source of light in all indoor growing
applications.
We strive to help you maximize your yields by offering the best lights that
emit a full-spectrum, sufficient light intensity (PPFD) that covers your
entire growing space.
Thank you for purchasing our products. We are sure you will be happy with the
results they help you achieve.
Package Contents
The package contains:
- LED Grow Light
- UV/IR Bars
- Steel Cables
- Plug Adapter
- Power Cord
- RJ Cord
- User Manual
Installation Instructions Wireless Control
Take caution when handling the light bars. Do not allow the LED diodes to come in contact with sharp objects that may damage them.
-
Unbox the light and place it on a flat surface. Make sure the surface is clear of objects that may damage LEDs.
-
Ensure the fixture is not plugged into the electrical power.
-
Press and hold to remove, lock, or adjust the steel cables. b. Loop the steel cables around a secure structure and back to the adjuster. c. Attach the carabiners of the hanging steel cables to the two hanging anchors.
-
Unfold the fixture and attach the carabiners of the longer steel cable to the hooks on each side. Adjust the cable by pressing the locking device.
-
Mount the UV/IR bars and connect the power cords on the side bars.
-
Connect the power cord to the light fixture and then plug it into a properly grounded power outlet.
-
Switch the rotary knob on all fixtures to “EXT.” Connect the controller to a power outlet.
-
Set Up Complete
Installation Instructions Wired Control
Take caution when handling the light bars. Do not allow the LED diodes to come in contact with sharp objects that may damage them.
-
Unbox the light and place it on a flat surface. Make sure the surface is clear of objects that may damage LEDs.
-
Ensure the fixture is not plugged into the electrical power.
-
Press and hold to remove, lock, or adjust the steel cables. b. Loop the steel cables around a secure structure and back to the adjuster. c. Attach the carabiners of the hanging steel cables to the two hanging anchors.
-
Unfold the fixture and attach the carabiners of the longer steel cable to the hooks on each side. Adjust the cable by pressing the locking device.
-
Mount the UV/IR bars and connect the power cords on the side bars.
-
Connect one end of the R.1 cord to the RJ port in the controller, and connect the other end of the R.1 cord to the DIM IN port of the LED GROW LIGHT. Repeat the same action until you have wired all your fixtures.
-
Switch the rotary knob on all fixtures to “EXT.” Connect the controller to a power outlet.
-
Connect the controller to the first or last fixture using the 11.1 cord. Connect the controller to a power outlet. Set-up complete.
Product Dimensions
Warranty Service
If the product does not work after you have read the troubleshooting guide and
practiced the troubleshooting options, please return the light to our
warehouse or the retailer where you purchased it. The dealer will be able to
examine the light and test its components. If they are not able to repair the
light, they will return it to us for examination and repair/replacement. Do
not attempt to repair any product on your own, as serious injury or death may
result. If the retailer is not able to help you and the product is still under
manufacturer’s warranty, you may contact us for technical support.
If we commence a return process, please return the light with all its original
packag-ing, and your receipt of purchase, to the address we will provide you
in the email. Please pack and ship the product in its original packaging. If
the light is damaged during shipment we cannot be responsible and the warranty
may be voided. Once we receive your return package, we will repair or replace
it and ship it back to you.
Thank you!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>