SEALEY AS10 Axle Stands Pair 10 TONNE Capacity Per Stand Instructions
- June 3, 2024
- SEALEY
Table of Contents
AS10 Axle Stands Pair 10 TONNE Capacity Per Stand
Instructions 
AS10 Axle Stands Pair 10 TONNE Capacity Per Stand
AXLE STANDS (PAIR) 10 TONNE CAPACITY PER STAND
MODEL NO: AS10
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions and maintained
properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction manual
SAFETY
WARNING! DO NOT OVERLOAD AXLE STANDS BEYOND RATED CAPACITY. OVERLOADING
CAN CAUSE DAMAGE TO, OR FAILURE OF, THE AXLE STANDS. POSITION LOAD ON CENTRE
OF CRUTCH/SADDLE ONLY. ALWAYS USE STANDS IN PAIRS ON HARD LEVEL SURFACE
CAPABLE OF SUSTAINING THE LOAD. USE OF STANDS ON OTHER THAN HARD LEVEL
SURFACES CAN RESULT IN LOAD INSTABILITY AND POSSIBLE LOSS OF LOAD. DO NOT USE
ON TARMACADAM. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO
AXLE STANDS, LOSS OF LOAD RESULTING IN PROPERTY DAMAGE, SERIOUS PERSONAL
INJURY OR LOSS OF LIFE.
DANGER! GREAT CARE MUST BE TAKEN TO ENSURE YOU LOWER THE VEHICLE (OR OTHER
LOAD) SLOWLY AND CAREFULLY ONTO THE CENTRES OF THE CRUTCH/SADDLE OF THE AXLE
STANDS.
Use only as specified by the manufacturer.
Ensure the load does not exceed the maximum capacity as marked on the axle
stand, per pair.
Use no more than a single pair of stands either on the front, rear or one
side of the vehicle. Use in pairs.
No alterations or modifications shall be made to this product.
Use on a hard, level surface, e.g. concrete. DO NOT use on uneven ground or
tarmacadam.
Securely chock wheels in contact with the ground. Before jacking and placing
the stands, apply vehicle handbrake (put automatics in `Park’).
Make sure that each stand is securely located under a strong point on the
vehicle; consult the vehicle manufacturer’s handbook for guidance.
Ensure that height adjust locking mechanism is fully located before applying
any load to the axle stand.
Ensure that the load is located centrally on the saddle, and that the weight
is directed through the vertical axis of the stand.
Exercise extra care when using with a three wheeled vehicle or a trailer.
Refer to vehicle manufacturer’s instructions.
Once vehicle is supported, ensure that the vehicle and stands are stable
before starting work.
Ensure that it is not possible for the vehicle to move before commencing any
work.
Inspect stands before each use. DO NOT use if they show signs of damage. DO
NOT use if it is suspected that they have been overloaded.
Before commencing any work or going beneath the vehicle, undertake a risk
assessment. Ensure that a responsible person is aware of the work about to be
undertaken.
Replace any labels on the axle stand should they become unreadable. This
applies in particular to any warning or operation instruction labels. If
replacement labels are required, contact your Sealey stockist.
X DO NOT use axle stands on the highway, or anywhere else if it is deemed
to be unsafe.
X DO NOT push or twist the vehicle/load whilst it is supported on
stands.
X DO NOT mix components between stands. Use only as supplied.
X DO NOT allow children or animals in the vicinity of a vehicle
supported on axle stands.
X DO NOT leave a vehicle on axle stands in an area that could be
considered a hazard to others or property.
FOLLOW STEPS 1, 2, AND 3 TO CORRECTLY PLACE VEHICLE / LOAD ONTO AXLE
STANDS.
INTRODUCTION
Heavy-duty axle stands to safely support vehicle for extended periods of time. Heavy gauge steel frame and welded construction give superior strength and safety. Large crutch for even load distribution. Features captive, multi- position pin load support. Ideal for commercial and public service vehicles. Sold in pairs.
SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . AS10
Capacity Each: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Tonne
Capacity Pair: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Tonne
Minimum Working Height: . . . . . . . . . . . . . . . . . . . . 573mm
Maximum Working Height: . . . . . . . . . . . . . . . . . . . . . 775mm
OPERATION
4.1. Refer to vehicle handbook for correct jacking procedure. Check to ensure
manufacturer’s recommended jacking points are in good condition.
4.2. Position stands under recommended support points.
4.3. To adjust stands, lift column up to jacking point, lower until next pin
hole is visible, push pin all the way through it.
4.4. Carefully and slowly lower vehicle onto stands. Ensure load bearing
points sit in the centre of the crutches and that the stands are stable.
Also ensure that there are no objects or persons that could impede the safe
lowering of the vehicle onto the stands.
▲ DANGER! You must follow instructions carefully and ensure you DO NOT load
the stands off centre. Failure to heed these warnings may cause damage, injury
or loss of life.
MAINTENANCE
5.1. Before each use, check that stands and stand welds are not cracked and
that there are no missing or damaged parts. Any suspect axle stands must be
removed from service immediately.
5.2. Owing to the potential hazards associated with stands do not misuse, or
make any modification, to the stands or components.
5.3. It is the responsibility of the owner to ensure that the operator has
read these instructions together with the safety features on the side of the
stand and that the operator is familiar with its use and limitations.
Parts support is available for this product. Please email sales@sealey.co.uk
or telephone 01284 757500
ENVIRONMENT PROTECTION
** Recycle unwanted materials instead of disposing of them as waste. All
tools, accessories and packaging should be sorted, taken to a recycling centre
and disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty:** Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business
Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
AS10 Issue: 4 (3) 24/08/22
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>