chicco 360 Seat Instruction Manual

: June 3, 2024
: chicco

chicco 360 Seat Instruction Manual

INSTRUCTIONS FOR USE

IMPORTANT – READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.

WARNING: KEEP PLASTIC COVERING AWAY FROM CHILDREN TO AVOID SUFFOCATION.

WARNINGS

Only for domestic

• WARNING:

Never leave the child
Always use the child restraint and table attachment
Always check the security and the stability of the product before us- ing.
Maximum weight: 15 kg.
WARNING: This product is in- tended for children able to sit up

• Age range intended for use:

from 6 months onward.

WARNING: Do not use table- cloths or other objects on the ta- ble that might interfere with the proper functioning of the anchor- ing elements. Keep the table struc- ture and surface clean and

• WARNING: Routinely check

any clamping devices and tighten them if required.

WARNING: Do not use the prod- uct if any component is broken, torn or
WARNING: Do not use accessories or replacement parts other than those approved by the manufac- turer or distributor.
WARNING: Do not attach the product where the child might use its feet to push against a part of the table, another chair or any oth- er structure as this could cause the product to come off the
WARNING: This product is not suitable for use with all Do not use with glass-topped ta- bles, tables with loose table tops, table leaves, single pedestal tables, card tables, camping tables or any other table that does not offer suf- ficiently stable support.
WARNING: Check that the table will not tip over when the prod- uct, attached to it, is in use.
The table top must have a mini- mum thickness of 19 mm and a maximum of 36
Do not fasten it to drawers or mo- bile parts of the
Do not hang objects on the seat

that may alter its stability.

Do not fasten or lock the seat when the child is in
Do not use the seat for more than one child at a

•Never allow other children to play near the seat unattended.

Keep this product out of reach of children when it is not in

CARE AND MAINTENANCE

This product requires periodical
Cleaning and maintenance operations must only be carried out by an
Periodically check the hook on chair to see if it is broken, damaged or has missing parts: if present don’t use the produc
Dry the metal parts to prevent the formation of
Periodically clean the space between the rotating plastic part and the fixed plastic part of the seat with a toothbrush to remove any food

Please refer to the care label for instructions on cleaning the fabric.

Hand wash
Do not bleach
Do not tumble dry
Do not iron
Do not dry clea

COMPONENTS

Frame (fixed section)
Seat with fabric (rotating section)

B1. Button to release the seat from the frame

B2. Plastic tabs for fastening the seat to the frame

B3. Child restraint belt

B4. Restraint belt buckle

B5. Tabs for fastening the fabric to the seat

Arms with non-slip rubber

C1. Metal pins for fastening to the frame

Fastener clamps

D1. Rubber fastening pins D2. Buttons for releasing pins D3. Buttons for locking pins

FIRST ASSEMBLY

Pull the product out of the bag.
Position the frame “A” on a level surface. Incline the seat with the fabric “B” just a little to insert the plastic tabs “B2” into the frame “ A ” (Fig. 1). Press down on the rear section of the seat “B” to lock it into place (Fig. 2). Verify that the tabs are under the frame “ A ” (Fig. 3).
Flip the resulting structure upside Press the metal pins “C1” on the arms with non-slip rubber “C” and insert the arms into the frame one at a time (Fig. 4). Once the arms have been inserted, verify that the pins “C1” emerge from the holes on the frame (Fig. 5).
Keep the product upside down and insert the fastening clamps “D” into the bottom part of the frame “A” being careful to pair the letters found on the pins with those found on the frame (Fig. 6). During insertion, two metal pins (Fig. 7) will need to snap into place for each

USE

If there is insufficient space between the pins “D1” and the arms “C” , press the release buttons “D2” on the two pins to lower them (Fig. 8). You may need to gently press the two pins down- wards, in order to create an opening.
Slide the seat onto the tabletop (Fig. 9). If there are obstacles on the underside of your table, be sure that the pins are fixed in place beyond the obstacle (Fig. 10).

WARNING: Make sure there are no gaps between the seat and the tabletop (Fig. 11).

To fasten the seat to the table press the two buttons “D3” until the pins “D1” have come into complete contact with the under- side of the table (Fig. 12).
Verify that the arms with non-slip rubber “C” lie flat and adhere fully to the upper surface of the table (Fig. 13). If they don’t adhere completely, press the buttons “D3”

WARNING: Verify correct installation on the tabletop by attempting to pull the seat outwards. At this point, the seat is ready to be used.

USING THE SAFETY HARNESS

After having placed your baby in the seat always fasten the safety belts by fastening the buckle “B4” (Fig. 14). The length of the belt “B3” can be adjusted by pulling the belt through the ladder lock (Fig. 15).

SEAT ADJUSTMENT

The seat can be rotated 360°, it can be adjusted in 4 different posi- tions (Fig. 16).

To adjust the position of the seat “B” take hold of the seat fromthe top with two hands and rotate clockwise or anticlockwise until you reach the desired position (Fig. 17).

WARNING: do not adjust the seat to a position of use other than those indicated in this instruction booklet. The seat must never be adjusted while the child is sitting in it. In this case it can be slightly more difficult.

WARNING: While adjusting the seat, make sure that the child’s legs can freely follow the movement of the seat.

REMOVING THE SEAT FROM THE TABLE

To remove the seat from the table press the pin release buttons “D2” (Fig. 18). If the release buttons are difficult to press, press gently on the pin lock buttons “D3” while simultaneously press- ing on the release buttons “D2” (Fig. 19).
Pull the seat off of the tabletop (Fig. 20).

WARNING: Do not remove the seat from the table with the child seated inside.

CLOSING THE SEAT

To make the product as compact as possible the two fastening clamps “D” can be folded inwards by pressing on the pins and rotating them (Fig. 21-22).

REMOVING THE FABRIC

The seat fabric can be taken off of the table seat and washed.

Disconnect the seat “B” from the frame “A” using the release button “B1” (Fig. 23).
Flip the seat “B” upside down and press down on the fabric through the frame of the seat (Fig. 24).
Raise, rotate, and press the eight tabs “B5” through the slots to extract them from the seat “B” (Fig. 25-26-27-28).
Remove the fabric from the frame (Fig. 29)
Remove the panel on the base of the seat from the fabric (Fig. 30). The fabric can now be washed following the instructions provided in the “MAINTENANCE SUGGESTIONS”

To fit the fabric cover back on the seat, repeat the steps illustrated above in reverse order. Be sure to align the fabric and the seat frame correctly. Specifically, start from the tab found next to the Chicco logo on the backrest and insert it into the slot located next to the number 1 (Fig. 31). Continue with all the other tabs being sure that each tab adheres firmly to the recess into which it is inserted (Fig. 32-33).

DISASSEMBLY AND TRANSPORT

Proceed as follows for product disassembly.

Remove the fastening clamps “D” by pressing on the lower pin and rotating the clamp a little (Fig. 34). Next, press on the other pin and pull out the clamp (Fig. 35). Repeat the operation with the other
Remove the arms “C” by pressing on the pin and pulling them out of the frame (Fig. 36).
All the components of the product can now be placed inside the bag for

WARRANTY

The product is guaranteed against any conformity defect in normal conditions of use as provided for by the instructions for use. The warranty shall not therefore apply in the case of damages caused by improper use, wear or accidental events. For the duration of warran- ty on conformity defects please refer to the specific provisions of na- tional laws applicable in the country of purchase, where provided.