WARNING:
Replace the lamp unit after the lamp has cooled (after waiting at least one hour).

• The high temperature inside the cover will cause burns.

Attention

• When the projector is mounted on the ceiling, do not make the replacement while your face is near the lamp unit.
• Do not remove or loosen the screws other than specified ones when replacing the lamp unit.
• Use four lamp units of the same type.

**Set the switch to and disconnect the power plug from the power

outlet.**

• Wait at least one hour and check if the lamp unit has cooled down.

Remove the lamp unit cover.

WARNING:
Be careful to hold the lamp unit cover and to loosen the lamp unit cover fixing screws with the projector installed upward in the vertical direction since the lamp unit cover may open and the lamp case may drop off on its weight.

• This can cause severe injury or accidents.

 (i) Use a Phillips screwdriver to loosen the lamp unit cover fixing screw (one screw)
counterclockwise until it turns freely, and then open the lamp unit cover slowly in the direction of the arrow.

• Opening the lamp unit cover quickly may result in damage to the cover.
• If you loosen the lamp unit cover fixing screw with the projector installed upward in the vertical direction, the lamp unit cover may open due to its weight and fall off. When loosening the lamp unit cover fixing screw, be sure to support the lamp unit cover with your hand.

(ii)Hold the lamp unit cover securely and slide it in the direction of the arrow, and then pull it out backward to remove.

• Since the fan and other components are attached to the lamp unit cover, handle
  the removed lamp unit cover with care.

Pull out the lamp case.

• Use a Phillips screwdriver to turn the lamp case fixing screws of the lamp unit to be replaced (two screws each) counterclockwise until they turn freely, and then hold the lamp case handles to be replaced and pull out backward.
• Do not remove the black screws other than the lamp case fixing screws.
• When you loosen the lamp case fixing screws with the projector installed upward in the vertical direction, the lamp case may drop off on its weight. Be sure to hold the lamp case handle when you loosen the lamp case fixing screws.
• When removing the lamp case, make sure that the projector is stable and remove it in a safe place where the lamp case is dropped off.

Remove the lamp unit.

• Use a Phillips screwdriver to turn the lamp unit fixing screws (two screws) counterclockwise until they turn freely, and then remove the lamp unit from the lamp case.
• Hold the handles of the lamp unit and remove it straight.
• Do not remove the screws other than the lamp unit fixing screws.

Attach the lamp unit.

(i) Gently push the new lamp unit into the lamp case. Install the new lamp unit carefully so that the guide pins on the lamp case are inserted into the guide holes on the lamp unit.

• If the lamp unit is not installed properly, remove it and then gently install it again. Pushing it in forcibly or exerting excessive force may break the connector.

(ii) Use a Phillips screwdriver to tighten the lamp unit fixing screws (two screws each).

• Make sure to attach the lamp unit properly.

Attach the lamp case.

• Gently push in the lamp case along the grooves for the lamp case attachment guide on the projector, and then firmly tighten the lamp case fixing screws (two screws).

• When you secure the lamp case with the projector installed upward in the vertical direction, the lamp case may drop off on its weight. Be sure to hold the lamp case handle when you tighten the lamp case fixing screws.

• If the lamp case is not installed properly, remove it and then gently install it again.
  Pushing it in forcibly or exerting excessive force may break the connector.

• Make sure to attach the lamp case properly.

Attach the lamp unit cover.

(i) Align the lamp unit cover to the marks of (a) and (b) (○ and ∆) to attach as shown by the arrow.
(ii) Close the lamp unit cover in the direction of the arrow and use a Phillips screw driver to firmly tighten the lamp unit cover fixing screw (one screw).

• Make sure the connector at the side of the lamp unit cover is firmly inserted in
  the fan power connector.

• Make sure to attach the lamp unit cover properly

Note

• When you place the new lamp unit, the projector resets the total usage time of the lamp unit automatically.
• When the lamp case is removed or attached, it will be caught because of the fall-prevention stopper. This, however, is not a problem.

Attention

• After unpacking the lamp unit, discard the packaging material properly

Manufactured by:
Panasonic Connect Co., Ltd.
4-1-62 Minoshima, Hakata-ku, Fukuoka 812-8531, Japan
Importer:

Panasonic Connect Europe GmbH

Authorized Representative in EU:

Panasonic Testing Centre
Winsbergring 15, 22525 Hamburg, Germany

Importer for UK;

Panasonic Connect UK,
a branch of Panasonic Connect Europe GmbH,
Maxis 2, Western Road, Bracknell, Berkshire, RG12 1RT

Disposal of Old Equipment

Only for European Union and countries with recycling systems

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products must not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to
applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment.

For more information about collection and recycling, please contact your local authority. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

Panasonic Connect Co., Ltd.
Web Site : https://panasonic.net/cns/projector/
© Panasonic Connect Co., Ltd. 2022

References

• Lamp Recycle – Environmental Responsiblility Starts Here
• Projector | Panasonic Global

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>