iSAVER Power+ 1100 Aquagem Pool Pump User Guide

iSAVER Power+ 1100 Aquagem Pool Pump

Thank you for purchasing our frequency inverter. Please read the manual carefully before installation & operation and keep it for future reference after installation.

SAFETY SYMBOLS

IMPORTANT SAFETY INSTRUCTIONS

To make the best use of this energy-saving device and to avoid the potential risk of fire, electrical shock, SERIOUS injury to people or damage to property, please read this user guide carefully before installation and keep it for future reference. This device can ONLY be used with pool pumps with a permanent split capacitor motor. The schematic diagram below shows a typical single-speed swimming pool pump motor.

It is NOT compatible with:

• Single-phase motors with centrifugal switch
• Pool pump motors with start relays or switch
• Series or DC motors
• Pool pump motors with faults in their rotors or capacitors
• Shaded-pole asynchronous motors

An RCD with a rated residual current not exceeding 30mA must be used with this product. If you are not sure of the compatibility of your pool pump with this device, please contact your supplier or manufacturer before proceeding with the installation.

TECHNICAL DATA

Pool-](https://manuals.plus/wp-content/uploads/2022/12/iSAVER-Power-1100 -Aquagem-Pool-Pump-User-guide-fig-3.png)
Input voltage| 220~240V| 220~240V
Input frequency| 50Hz| 50Hz
Output power| Max 1.1kW| Max 2.2 kW
Output Voltage| 1ph, 0~240V| 1ph, 0~240V
Pump type| Single phase| Single phase| **
Max. current| Max 6A| Max 12A
Speed range| 1200~2900 rpm| 1200~2900 rpm
Cooling| Ventilation| Ventilation/Fan
Net Dimension (LHW)| 187110155mm| 187110155mm
Gross/Net Weight| 3.0/2.7Kg| 3.0/2.7Kg

BEFORE INSTALLATION

Upon receipt of this device, check for damage to the packaging or product. DO NOT PROCEED with installation if any damage is found; contact your supplier. Do not use extension leads with the device. This can pose a danger, particularly in the vicinity of a swimming pool. Make sure the place you choose for installation meets the following conditions:

•  Ambient temperature from -10~40℃
•  45 to 90 percent relative humidity, non-condensing
•  Less than1000m above sea level
•  Keep out of direct sunlight
•  Good ventilation

For efficient cooling, please make sure it is installed with a minimum clearance surrounding it (Fig2) Blocked ventilation or an enclosed space with limited airflow may cause overheating or potential operational failure of the inverter.

CONNECTING TO POOL PUMP
Please follow these steps and the wiring diagram for the correct connection. The warranty may be compromised if the device is not installed in accordance with the instructions described in this manual. Only ONE pump can be connected to the inverter. Please do not connect any other appliance to the output.
Mark the hole locations on the wall, drill and insert the expansion plugs supplied, fit the screws and hang the device on the screws.

• Turn off all electrical supplies to the pool pump, and unplug it from the main switch or at the chlorinator which provides electrical power to the pump.
•  Plug the pool pump into the device’s power outlet (marked PUMP CONNECTION ONLY). 4.3 Plug the device into the main switch/chlorinator/timer connection where the pump was originally plugged into.
• Switch all power back on.
• Ensure the chlorinator/timer is active.
• Now the device is ready to operate.
• The above figure is for reference only, plug & socket may vary for different countries/regions. If you do not require a power plug for installation, wire the device as shown in Fig.4, please.
• Do not touch the heat sink while the device is in operation or until at least 30 mins after it has been switched off. Keep it out of reach of children.
• Because of the high voltage conversion components contained in the device, do not try to disassemble or replace any components in case of malfunction or breakdown. Before serving on the unit, wait till the power light is turned off or at least 3 minutes after the power plug has been plugged off from the input supply.

SETTINGS & OPERATION

Control panel

Mode selection
The frequency inverter has 3 modes(speed ranges). You can either run your pump at a constant speed choosing from “M” or set up to 4 timers for daily operation, each with an individual speed.

1. When plugged in lights up, and holds for 3 seconds to unlock the screen.
2.  Upon starting, the pump will run at a maximum speed of 2900 rpm for one-minute self-priming. (This can be increased to 10 minutes – see Parameter settings Section 5.5)
3. Press to start.
4. Once the pump has finished priming, the inverter will automatically switch the pump to the pre-set speed

Timer setting
To run the pump at different times or speeds to take advantage of lower electricity tariffs during the night, you can set up to 4 timers.

Step 1 : Press to enter the timer setting.

Step 2 : Use or to set the current time. Press to move cursor to the next setting. Press choose a speed range for the timer and use it to

decide on a specific speed if required. Press to move the cursor to the previous setting.

Step 3: Repeat the above steps to set the other 3 timers.

Step 4: Hold for 3 seconds or wait 10 seconds to save settings automatically. A flashing indicates the device is waiting for the start time.

Step5: press or to check all 4 timers to ensure there are no invalid settings.* Any overlapping of timer periods will be considered as invalid and the device will only run based on the previous valid timer setting.

External control

External control can be enabled via the following contacts. However, even if it’s working via an external controller, Pressing can stop the device. Please do not apply voltage to these inputs.

E.g.: To enable external speed control via digital input, connect one of the digits from Di2/3/4 to COM.

Parameter setting

Under OFF mode, hold for 3 seconds to enter parameter settings.

PROTECTION & ERROR CODES

1.  AL01 is not an error indication: when it appears the inverter will automatically switch to a lower speed to self-protect against high internal temperature. When the temperature drops back to 65℃ the inverter will resume at the preset speed.
2.  When causes for E002/E101/E103 lifts, the device will resume working automatically, however, when it appears a fourth time, the device will stop working, to resume operation, unplug the device and plug in & restart again.

EXCLUSIONS
Under no circumstances should the manufacturer be held liable for any consequences resulting from inappropriate, incorrect installation, or mismatching of the product to pool pumps that are not compatible. The manufacturer reserves the right to change the specification of the product or its performance or the contents of the User Guide without notice in case of a technical upgrade.

WEEE LEGISLATION
When disposing of the product, please hand it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of waste equipment at the time of disposal will help ensure that it is recycled in a manner that protects human health and the environment. Contact your local authority for information on where you can drop off your water for recycling.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>