GE current Daintree EZ Connect App User Guide
- June 4, 2024
- GE current
Table of Contents
GE current Daintree EZ Connect App
Daintree EZ Connect
Daintree EZ Connect wireless lighting controls solution allows a group of adjacent fixtures to communicate with each other directly, without the need for a separate hub, gateway or cloud operating system. Daintree EZ Connect app can commission WIT100, WIZ20, WHS20 sensors, WA200 Series room controllers and WWD2 Series or ZBT-S1AWH wall controllers and is connected as part of a room based lighting control system. The system can be commissioned, put into rooms, groups or zones and control parameters can be set via the Daintree EZ Connect app that can be downloaded on the Apple® App Store.
Open application
You will be asked to create a username and password the first time you open the App.
Adding new room or zoned networks
A zone is a grouping of fixtures that all act together according to parameters
that are set.
Select “Automatic” to allow the Daintree EZ Connect system to select the best
wireless channel (recommended).
Different room or zones can be on the same channel.
Add nodes to your room or zone
Nodes are any Daintree Control component that wirelessly communicate with the
Daintree Wireless Controls system. The nodes can include components such as
sensors integrated into Current lighting fixtures, wall controls or WA200
Series room controllers.
The Daintree EZ Connect app will search for available nodes and the light
fixtures will blink when successfully paired with the app.
The user can choose to add the fixture to the roomor zone.
This process will continue until all the devices within the communication
range are discovered.
Max 30 nodes per room zone, but the system can accommodate thousands of
independent rooms or zones.
Room commissioning
If you have not discovered all of the devices you intend to include in a
group, you can choose to ADD MORE devices.
Note: The commissioning process responds to fixtures that are closer in
proximity to make it easier for field commissioning. You may want to move
closer to devices you want to commission in the room or zone.
If all the devices have been selected, choose OK
Group profile configuration
The group profile can be customized based on the needs of the room and the requirements of the user.
Setting Definitions:
Dwell Time – Time required for occupancy to be detected before a change
of state is initiated.
Hold Time – The time (measured in minutes) that occupancy must NOT be
detected for a fixture to transition from Task state back to Background state.
Grace Time – In vacancy mode, amount of time when fixture is in
background mode and no occupancy is detected before it will switch the fixture
off and can only be manually switched back on.
Background Level – Light level when no occupancy is detected, but
occupancy is detected by a fixture in the group.
Task Level – Light Level when occupancy is detected under the luminaire.
Daylighting – Daylight Harvesting Function enabled or disabled.
Occupancy Strategy – Vacancy-Detection or Automatic (Occupancy).
See Daintree EZ Connect website for the user manual for more details on
parameters and default settings.
Daylighting profile can be adjusted in the group profile by selecting the
turning on the daylighting tab and adjusting thresholds.
Alternatively, Daylight sensitivity can be adjusted based with the visual
daylight sensitivity tab based on the zone proximity to windows or skylights.
Alternatively, Daylight sensitivity can be adjusted based with the visual
daylight sensitivity tab based on the zone proximity to windows or skylights.
Adding a switch to control the room network
See Daintree EZ Connect website for compatible switches. Select “Add new switch”. You will be asked to scan the QR code on the back of the switch. The app will pair the switch to the appropriate zone.
Advanced diagnostics can be run on the Daintree EZ Connect app to monitor the health of the devices within the zone.
gecurrent.com/daintree
© 2022 Current Lighting Solutions, LLC. All rights reserved. Information and
specifications subject to change without notice. All values are design or
typical values when measured under laboratory conditions.
Documents / Resources
| GE
current Daintree EZ Connect
App
[pdf] User Guide
Daintree, EZ Connect App, Daintree EZ Connect App, Connect App, App
---|---