Pink Powert PP121LI Cordless Drill Kit Instruction Manual
- June 3, 2024
- Pink Powert
Table of Contents
Pink Powert PP121LI Cordless Drill Kit Instruction
Thank you for your purchase from Pink Power
We hope our tools will help you with any project you approach. whether you are building a deck or just hanging a picture. We designed our tools specifically for women and hope they will help you complete your tasks. We are proud of our Pink Power line and happy to offer you quality tools. All of our tools come with a full 3 year warranty. If any damage occurs to your tool. battery or charger just reach out to us using the information below and I will replace your tool at no cost to you. We greatly appreciate your business.
FEATURES
- Keyless Chuck
- 18• llorque Setting
- Battery Power Gauge
- Direction Selector /Switch Lock
- ON/OFF Trigger
- Battery Pack
- LED light
OPERATING INSTRUCTIONS
CHARGING THE BATTERY PACK
The battery pack for this tool has been shipped in a low charge condition to
extend battery life. The battery should be fully charged prior to use.
Batteries will not reach full charge the first time they are charged. Please
allow several cycles (driling followed by recharging) for the battery to reach
full charge. Do not charge the batteries in areas of extreme heat or cold.
CHARGING INDICATION
Connect the charger toa wall outlet and the Green light will iluminate. Put
the battery into the charging base and the Green and Red light will luminate
together. This means the battery is charging.
REMOVAL/INSERTION OF THE BATTERY
Before placing the battery pack in the drill, make sure the Switch Lock4 is in
the center position. This keeps the drill in a locked stage. Hold the drill
with one hand and insert the stick of the battery directly into the bottom of
the drill using the other hand. To remove the battery, press in the 2 buttons
on the side of the battery pack (one on each side) and pull down. This will
release the battery.
BATTERY GAUGE
The drill is equipped with a battery gauge on the side of the drill. When
puling the triggerthe gauge will iluminate. If all 3 lights are illuminated,
your battery is fully charged. If 2 lights are illuminated, your battery is at
50% charge. If just 1 light is illuminated, you need to recharge the battery
pack.
SWITCH LOCK &ON/OFFTRIGGER
The switch look 4 comes with 3 positions. When holding the drill away from you
push the switch lock all the way to the left and your drill is in the forward
position. Push the switch lock all the way to the right and your drill is now
in the reverse position. To lock your drill, push the switch lock to the
center position. To use your drill, just pull the ON/OFF Trigger 5. Release
the trigger and the electric brake stops the dril.
INSERTING AND REMOVING DRILL BITS
Make sure the switch lock 4 is in a locked state (center position). Face the
front of the drill towards you and twist clockwise to tighten the chuck 1 and
counter-clock- wise to release the chuck.
TORQUE ADJUSTMENT
The torque is adjusted by rotating the torque setting. Your drill comes with
18 torque settings and 1 setting for drling holes. When driving a screw, start
with a lower setting and increase the settings as needed. The lower setting
should be used for softer materials while the higher settings should be used
for harder materials. When using a drill bit to drill a hole use the last
setting (shaped like a drill bit).
TOOL SAFEIY
SAFETY
Do not use power tools under the influence of medication, drugs or alcohol as
this could result in serious personal injury. Keep hair, clothing, jewelry and
other loose objects away from moving parts. Use the proper safety equipment
when operating power tools. This may include eye or dust protection equipment.
The power tool plugs should never be modified in any way as this could
increase the risk of electric shock of malfunction. The tool should be in a
locked state when not in use Do not force use of the power tool. Make sure to
always ensure proper balance when using power tools. If your tool is damaged
stop use immediately.
WORKING AREA
Keep working area clean and well it. Cluttered and dark areas can lead to
accidents. Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks which
may ignite fumes and dust.
CLEANING AND MAINTENANCE
Always remove the battery before cleaning. Remove dust and dirt with a cloth
slightly dampened with solution. In doing so, ensure that no water gets into
the inner dril Clean drillings and dust out of the chuck regularly. The drill
is permanently lubricated and does not require oiling.
BATTERY USE AND CARE
Only use the included charger to charge your battery. Not using the correct
charger could cause injury or damage to your tool. Abuse of the tool can lead
to battery leakage. Avoid contact with battery fluid. If contact occurs, seek
medical help immediately. Never attempt to open the battery for any reason.
Only charge and store the battery between temperatures of 39°F and 70°F
DISPOSAL OF BATTERY
To preserve natural resources please recycle or dispose of the battery
properly. This product contains lithium batteries. Consult your local waste
authority for information regarding available recycling and/or disposal
options.
TECHNICAL DATA
Rechargeable battery| 12v Lithium Ion
Battery capacity| 1,300mAh
No-load soeed| 0-350/0-1,250
Drill chuck capacity| 10mm
Torque setting| 18+1
Charge time| 3-5 hours
Warranty Information
T Full 3 years against ANY defects ar damage 1.888.989.7249 Customerservice@pinkpowerdrill.com www.PINKPOWERDRILL.COM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>