MOGO T2 4G Wireless Data Terminal User Manual
- June 6, 2024
- MOGO
Table of Contents
MOGO T2 4G Wireless Data Terminal
Statement of Conditions
In the interest of improving internal design, operational function, and/or
reliability, iFREE GROUP reserves the right to make changes to the products
described in this document without notice.
iFREE GROUP does not assume any liability that may occur due to the use or
application of the product(s) or circuit layout(s) described herein.
Introduction
Thank you for purchasing the MOGO T2, 4G Wireless Data & GPS Tracking Device. This device brings you a high speed wireless network connection and global position. MOGO T2 is a well-designed product to provide you and your family high-speed wireless access and give them the peace of mind.
MOGO T2 Structure Diagram
Steps to use MOGO T2
Binding the MOGO T2
Before first use, please scan to download the M Track.
www.ifree.ly/mtrack Scan ta dawnlaad M Track
- Register as a T2 user or Log in with your FREE account.
- Scan the QR Code either on the back of the box or user manual to bind T2.
Turn Bluetooth on to enable the connection between your smartphone and T2.
Purchases Data Package
After binding your device, purchase the data plan via M Track> Store
ShareWiFi
- Turn on the T2 to connect to the network.
- Check the WiFi name and enter the password. Or scan the WiFi sharing QR code by the T2 admin.
Please ensure you have data purchased the package for your T2.
Track belongings
After attaching your T2 to the preferred item, it can help to find your
belongings by real-time positioning and two-way separation alert with multiple
location technologies.
Activate SOS alarm
Long press for 3 seconds (not the power off page) until the screen display the
‘SOS’, and the M Track will pop up the alarm.
Specifications
| Product Name | 4G Wireless Data & GPS Tracking Device |
|---|---|
| Model | T2 |
Network Specifications
|
Frequency Bands
Data Rote
|
FDD-Lff B1/B2/B3/B4/B5/B7
/B8/B20/B12/B13 TDD-LTE: B38/B40/B41 UMTS: B1/B2/B4/B5/B8
Download: 150Mbps Upload: 50Mbps
SIM Card| VSIM
WiFi| WiFi Mode
Data Rate
| 802.11b/g/n
300Mbps
Multi-Positioning| GPS/GLONASS/WiFi/LBS/G-sensor
Bluetooth| Two-way alarm (up to Bluetooth5.0)
Beep Alarm| Support
Charger| Type-C/Magnetic charging/Wireless charging
Input| 5V=1A
Dimensions| 101.3mm•6 □.2mm•13_4mm
Voltage| 3.8V
Battery Capacity| 2000mAh
Standby Time| 200 hours
Operating Temperature|
0°C – +45″C
Storage Temperature| -20°C – +70°C
Manufacturer| iFREE GROUP (HK) LIMITED
Warranty
If within 7 days of purchase this product or any part thereof is proven to be
defective by reason of faulty workmanship or defect in materials, we will
repair or replace the said product free of charge.
Battery Warranty: 6 months MOGO S2 Warranty: 12 months
Fair Usage Policy
Under the Fair Usage Policy, to avoid excessive downloads or uploads, service
providers have the right to restrict the data access speed without prior
notice.
iFREE reserves the right to limit returns or exchanges at any time, for
whatever reason. Any questions please contact our customer service center at
www.ifree.ly/support.
CE Warning:
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 5mm must be maintained
between the user’s body and the device, including the antenna. Third-party
belt-clips, holsters, and similar accessories used by this device should not
contain any metallic components. Body-worn accessories that do not meet these
requirements may not comply with RF exposure requirements and should be
avoided. Use only the supplied or an approved antenna. This device in
compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EU. All essential radio test suites have been carried out.
- CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
- The device complies with RF specifications when the device used at 5mm from your body
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information
This device meets the government’s requirements for exposure to radio waves.
The guidelines are based on standards that were developed by independent
scientific organizations through periodic and thorough evaluation of
scientific studies. The standards include a substantial safety margin designed
to assure the safety of all persons regardless of age or health. FCC RF
Exposure information and Statement The SAR limit of USA (FCC) is 1.6 W/kg
averaged over one gram of tissue. Device types: T2 (FCC ID: 2AT7I-T2) has also
been tested against this SAR limit. The highest SAR value reported under this
standard during product certification for use at the body is 1.40W/kg. This
device was tested for typical body-worn operations with the back of the device
kept 10mm from the body. To maintain compliance with FCC RF exposure
requirements, use accessories that maintain a 10mm separation distance between
the user’s body . The use of accessories that do not satisfy these
requirements may not comply with FCC RF exposure requirements, and should be
avoided. Body-worn Operation This device was tested for typical body-worn
operations. To comply with RF exposure requirements, a minimum separation
distance of 10mm must be maintained between the user’s body and the device,
including the antenna. Third-party belt-clips, holsters, and similar
accessories used by this device should not contain any metallic components.
Body-worn accessories that do not meet these requirements may not comply with
RF exposure requirements and should be avoided. Use only the supplied or an
approved antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>