HINKLEY 55702 Well Light Instruction Manual

: June 3, 2024
: HINKLEY

Table of Contents

55702 Well Light
LED Engine Installation
Assembly Instructions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Installation Instructions
Well Light: Line Voltage | Item No. 55702
With included LED engine

55702 Well Light

LED Engine Optic Options

|
---|---

*** A ground flush to surface junction box or a thermal shrink tube kit can be used if a concrete pour kit is unavailable Start Here
SAFETY WARNING: TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITY FOR CODE REQUIREMENTS.
IMPORTANT OPERATION NOTE: This luminaire is designed to be operated with Hinkley approved 120 volt AC systems.
NOTE: Luminaire can be placed in an area where a car may drive over the luminaire.
Luminaire Mounting** (for typical in-ground mounting)

To prevent electrical shock, disconnect power supply from electrical supply before installation or service.
Luminaire may be directly buried in the ground. For concrete applica-tions, a removable burial sleeve and cap is included. Use cap when pouring concrete and discard after installation of the luminaire. (Make sure bottom hex nut is tight before burying fixture)
In earth burial applications, the best way to extend fixture life is to use sand, gravel or any other material to facilitate drainage.
Strip three wires (ACL – Black, ACN – White, GND – Green). Connect to main supply following local electrical code requirements.

Note: Wire is to be protected by routing in close proximity to the luminaire, fitting or next to a building structure such as a house or deck. Wiring should be buried a maximum of 6 inches (15.2 cm) in order to connect to main supply wire. The main supply wire must have its length cut off within 6 inches (15.2 cm) from a building, structure, luminaire or fitting.

LED Engine Installation

Three optics are included with the well light. A white spot lens, grey medium spread lens and a black hood lens . Place desired optic in the LED engine and twist to secure.

To prevent electrical shock, turn off power supply from electrical supply before installation or service.
Using a Phillips head screw driver, remove top screws and fixture top. Set these aside for use in reassembly.
Remove silicone gasket and glass lens
Put the LED engine assembly, with attached socket, into the pivot sleeve. The engine sits in the sleeve freely.
Adjust the light direction by turning the pivot sleeve. The sleeve itself can be turned 360º and the pivot cup inside has a 20º adjustment. The screws on the pivot sleeve can be tightened to secure the cup in the correct angle.
Return the silicone gasket and glass lens. Making sure the gasket isseated correctly. Make sure to align the cut-outs in the gasket to the screw holes
Screw the fixture top back on.

Drawing 1 – Engine Assembly| Drawing 2 LED wattage adjustment| Drawing 3 – Fixture Assembly Example
---|---|---
| |

Assembly Instructions

Item No: 30G4SE-120V and 27G4SE-120
Start Here

In order to lamp the fixture you need to first assemble the engine.
Take the optic (O) and push it into the top of the engine (E) and twist it into place – see Drawing 1.
Note: Engine optic (O) comes in 3 types.
Hold the Lumacore with the Hinkley Logo so that its readable. The rotational switch (A) can be adjusted by your fingers or a small flat bladed screwdriver.
Rotate until the switch falls into a stop. For reference, the wattage settings are roughly akin to hours on a standard clock face. -See Drawing 2

1. After the engine is assembled, you can lamp the fixture by pushing the engine into place inside the enclosure.
2. Finish by reassembling the fixture – See Drawing 3
OUTPUT SWITCH SETTINGS

| 3 Watts, 3.2 VA, 260 Lumens
---|---
| 5 Watts, 5.3 VA, 350 Lumens
| 8 Watts, 7.8 VA, 475 Lumens
| 12 Watts, 12.4 VA, 750 Lumens
Black – Flood, 60°
Noir – Inonder, 60°
Negro – Inundar, 60°| White – Spot, 20°
Blac – Place, 20°
Blonco – Lugar, 20°| Grey – Medium Spread, 40°
Gris – propagation moyenne, 40°
Gris – propagación media, 40°
---|---|---