SEALEY VS2006.V4 Axle Stands Pair 6 ton Capacity Per Stand Ratchet Type Instructions
- June 3, 2024
- SEALEY
Table of Contents
AXLE STANDS (PAIR) – 6TONNE CAPACITY PER
STAND RATCHET TYPE
MODEL NO: VS2006.V4
VS2006.V4 Axle Stands Pair 6 ton Capacity Per Stand Ratchet Type
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions and maintained
properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR
THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE
FOR FUTURE USE.
Refer to instructions
SAFETY
• WARNING!
DO NOT OVERLOAD AXLE STANDS BEYOND RATED CAPACITY. OVERLOADING CAN CAUSE
DAMAGE TO, OR FAILURE OF, THE AXLE STANDS. POSITION LOAD ON CENTRE OF
CRUTCH/SADDLE ONLY. ALWAYS USE STANDS IN PAIRS ON HARD LEVEL SURFACE CAPABLE
OF SUSTAINING THE LOAD. USE OF STANDS ON OTHER THAN HARD LEVEL SURFACES CAN
RESULT IN LOAD INSTABILITY AND POSSIBLE LOSS OF LOAD. DO NOT USE ON
TARMACADAM. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO AXLE
STANDS, LOSS OF LOAD RESULTING IN PROPERTY DAMAGE, SERIOUS PERSONAL INJURY OR
LOSS OF LIFE.
▲ DANGER! GREAT CARE MUST BE TAKEN TO ENSURE YOU LOWER THE VEHICLE (OR OTHER LOAD) SLOWLY AND CAREFULLY ONTO THE CENTRES OF THE CRUTCH/SADDLE OF THE AXLE STANDS.
✓ Use only as specified by the manufacturer.
✓ Ensure the load does not exceed the maximum capacity as marked on the axle
stand, per pair.
✓ Use no more than a single pair of stands either on the front, rear or one
side of the vehicle. Use in pairs.
✓ No alterations or modifications shall be made to this product.
✓ Use on a hard, level surface, e.g. concrete. DO NOT use on uneven ground or
tarmacadam.
Securely chock wheels in contact with the ground. Before jacking and placing
the stands, apply vehicle handbrake (put automatics in ‘Park’).
✓ Make sure that each stand is securely located under a strong point on the
vehicle; consult the vehicle manufacturer’s handbook for guidance. Ensure that
height adjust locking mechanism is fully located before applying any load to
the axle stand.
✓ Ensure that the load is located centrally on the saddle, and that the weight
is directed through the vertical axis of the stand.
✓ Exercise extra care when using with a three wheeled vehicle or a trailer.
Refer to vehicle manufacturer’s instructions.
✓ Once vehicle is supported, ensure that the vehicle and stands are stable
before starting work. Ensure that it is not possible for the vehicle to move
before commencing any work.
✓ Inspect stands before each use. DO NOT use if they show signs of damage. DO
NOT use if it is suspected that they have been overloaded.
✓ Before commencing any work or going beneath the vehicle, undertake a risk
assessment. Ensure that a responsible person is aware of the work about to be
undertaken.
✓ Replace any labels on the axle stand should they become unreadable. This
applies in particular to any warning or operation instruction labels. If
replacement labels are required, contact your Sealey stockist.
DO NOT use axle stands on the highway, or anywhere else if it is deemed
to be unsafe.
DO NOT push or twist the vehicle/load whilst it is supported on stands.
DO NOT mix components between stands. Use only as supplied.
DO NOT allow children or animals in the vicinity of a vehicle supported
on axle stands.
DO NOT leave a vehicle on axle stands in an area that could be considered
a hazard to others or property.
FOLLOW STEPS 1, 2, AND 3 TO CORRECTLY PLACE VEHICLE / LOAD ONTO AXLE
STANDS.
INTRODUCTION
Ratchet type axle stands, with cast iron support posts and tough steel plate welded base. Features angled teeth in posts, which prevent accidental release of the load – the more weight applied, the tighter the post is locked. Sold in pairs.
SPECIFICATION
Capacity each: ……………………………………. 6 tonne (6000kg)
Capacity pair: …………………………………… 12 tonne (12000kg)
Min. Working Height: ………………………………………….. 395mm
Max. Working Height: …………………………………………. 600mm
ASSEMBLY
4.1. Insert the centre column into the base frame and stand (fig.1).
4.2. Ensure the toothed side of column will engage with the locking lever
mechanism (fig.2).
4.3. Bend in locking tab using a drift or similar and a hammer (fig.3).
4.4. Check the base frame and stand is in good condition and has not suffered
damage during transit.
OPERATION
5.1. Refer to manufacturer’s instructions for recommended jacking/support
points.
5.2. Check to ensure jacking/support points are in good condition. Position
the stands beneath their support points.
5.3. To adjust the stands:
Hold the control lever up while lifting the centre column to required height.
Push the control lever down to lock the pawl into the central column teeth
(fig.1 and fig.2).
• WARNING! ENSURE PAWL IS FULLY ENGAGED WITH TEETH.
5.4. Carefully and slowly lower vehicle onto stands. Ensure load bearing
points sit in the centre of the saddles and that the stands are stable.
5.5. Also ensure that there are no objects or persons that could impede the
safe lowering of the vehicle onto the stands.
▲ DANGER! You must follow instructions carefully and ensure you DO NOT
load the stands off centre. Failure to adhere to these warnings may cause
damage, injury or loss of life!
5.6. Insert the locking pin to store the stands in their lowest position.
MAINTENANCE
6.1. Before each use, check that stands and stand welds are not cracked and
that there are no missing or damaged parts.
Any suspect axle stands must be removed from service immediately.
6.2. Due to the potential hazards associated with stands, DO NOT misuse, or
make any modification to, the stands or components.
6.3. It is the responsibility of the owner to ensure that the operator has
read these instructions together with the safety features on the side of the
stand and that the operator is aware of the stand uses and limitations.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
| 01284 757500
---|---
| 01284 703534
| sales@sealey.co.uk
| www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
VS2006.V4 Issue: 1 19/08/21
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>