RRT LAUNCHER 10450 Dummy Launcher Stock Instruction Manual
- June 3, 2024
- RRT LAUNCHER
Table of Contents
LAUNCHER 10450 Dummy Launcher Stock
Instruction Manual
10450 Dummy Launcher Stock
VISIT GUNDOGSUPPLY.COM ORDER A RRT SHOULDER STOCK
SEE OTHER RRT PRODUCTS WWW.RRTLAUNCHER.COM MADE
IN THE USA
ULLY READ THE WARNINGS BEFORE OPERATING!
AMERICAN MADE AND BACKED BY A 1-YEAR WARRANTY.
SHOULDER STOCK INSTRUCTIONS
The stock that you have just purchased is designed specifically for use with
the Retriev-R-Trainer hand-held launcher. It will improve the distance and
accuracy of your shots and with practice can provide for single hand cocking
and firing—not possible without this accessory while using your hand held
launcher.
The stock is designed to work with RRT hand held launchers that were
manufactured from 1990 to the present. The grips used during this period will
require slight trimming to work properly with the stock. The only trimming
required will be at the base of the grip nearest the pull knob on the
launcher. This can be achieved by using a sharp utility knife or by turning
the base of the grip on a sander. The RRT Launcher should fit snuggly into the
stock. If you have recently purchased a new RRT Launcher (will have RRT
LAUNCHER on the grip in raised lettering) you will not have to modify/trim the
grip. Please reference image to the right. Your launcher grip must look
similar to the image below in order for it to slide into the shoulder stock
without modification. If you are unsure of any of the steps or procedures in
these instructions please contact us for further instructions and
assistance.
INSTALLATION OF THE TRIGGER
Included with the Shoulder Stock is a pull knob conversion kit consisting of a pull ring and allen wrench. Slide the pull ring over the pull knob until the allen set screw will engage the groove of the pull knob. The ring will be close to flush with the bottom of the pull knob. Tighten the set screw securely with the provided allen wrench.
SHOULDER STOCK ASSEMBLEY A LAUNCHER
Your Shoulder Stock is manufactured in 2 sections for easy portability and
storage. Section A is the end in which your Retriev-R-Trainer will be located.
Section B has the padded shoulder/thigh rest for your comfort during training.
To assemble, simply line up the hole in Section A with the locking button in
Section B. Slide the 2 parts together until the locking button is fully
engaged into the hole in Section A.
You are now ready to install your Retriev-R-Trainer into the shoulder stock.
Release the thumb latch on the launcher to make sure it is not loaded.
Position the launcher over the end of Section A while aligning the pull knob
pin with the slot in Section A. Keeping the pull knob pin aligned with that
slot, insert the launcher in the tube. Position the launcher so that the thumb
latch on the launcher is in line with the slot in Section A.
A light coating of lubricant will help the launcher slide easier into the
Shoulder Stock. If lubricant is used during installation, the grip of the
launcher must be cleaned throughly after it is removed from the Shoulder Stock
and before it is used as a standard hand held launcher.
MAINTENANCE
User must thoroughly clean the Shoulder Stock after each use. Be certain that the Shoulder Stock, Launcher, and Dummy are all free of debris prior to every firing/launch. Improper maintenance and failure to properly and firmly position the Shoulder Stock may result in serious injury or death.
PREPARATION FOR FIRING
Place the training dummy over the barrel of the Retriev-R-Trainer. Next, open
the launcher and insert the desired power load in the chamber. Make sure that
the load is properly seated in the chamber. Slowly place your
Retriev-R-Trainer into the closed position. Make sure that the thumblatch has
tightly secured the two sections (head and breech assembly) together.
ATTENTION: Never insert a power load in the chamber prior to placing a
training dummy over the barrel. To do so may cause premature firing due to the
displacement of air within the barrel pushing the load back in the chamber.
FIRING
Your Retriev-R Trainer can now be fired from either your shoulder or your
thigh/hip. From either position you must squarely place the padded butt end of
the stock against your body and maintain a firm grip on the stock. To rest it
only on an edge of the pad could cause serious injury or death. Aim the
Retriev-R-Trainer in the direction of your desired target area with your
holding hand positioned in such a manner as to allow you to slide your hand
toward the firing pin and grasp it with your index finger. Gently pull back on
the firing pin until you have reached the end of its travel. Firm up your grip
on the stock and release the pin firing the Retriev-R-Trainer.
The Shoulder Stock does not contain any parts that will rust or corrode. It is
guaranteed for one year from date of purchase against defects in material and
workmanship by the manufacturer.
LIMITATION OF LIABILITY
In no event shall TLB Industries, Inc. be liable for any direct, indirect,
punitive, incidental, special or consequential damages arising out of the use
or misuse of this product. By Using this product, you assume all risks and
liability in connection with it.
TLB Industries, Inc. shall not be liable for any damages arising out of or
connected with the use or misuse of this product. The buyer assumes all risks
and liability from the use or missuse of this product.
TLB Industries, Inc reserves the right to change the terms, conditions under
which this product is offered without further notice.
WARNING
- Handler must follow all instructions and warnings for the Pro Model Retriev-R-Trainer Hand Held Model Operating Instructions. If you do not have please go to www.rrtlauncher.com or contact us directly to receive a copy.
- Failure to assemble the components of this product correctly with your Retriev-R-Trainer Launcher in addition to following these instructions with use of your RRT Shoulder Stock may result in serious injury or death.
- Use extreme caution when using the Shoulder Stock and RRT Launcher.
- Recoil from Shoulder Stock may be too excessive for some users. Start with the lowest power loads (green) first.
DISCLAIMER
Any use or modification of the Shoulder Stock not in conformity with the
manufacturer’s instructions as described in this user’s manual is AT THE SOLE
RISK AND RESPONSIBILITY of the individual performing such unauthorized use
and/or modification. Direct any inquires regarding use to Specialty Products
Company prior to use or continued use of this product.
Visit our website for more great products.
wvvw.RRTLauncher.com
TLB Industries, Inc.
292 Dunn Road, Honesdale,
PA 18431 USA570-729-7192 I
570-729-7193
(Fax)info@rrtlauncher.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>