SEAORY R300 Desktop Retransfer Dual-Sided Card Printer User Guide
- June 3, 2024
- SEAORY
Table of Contents
R300 Desktop Retransfer
Dual-Sided Card Printer
**User Guide
**
Desktop Retransfer Dual-Sided Card Printer
Read before use: This manual only briefly describes the basic installation and use. If you need to know more about the use, installation and functional characteristics of this product or have other questions, please refer to the product manual of the corresponding model.
Introduction to Product Components
1.1 Front-end View
1.2 Back-end View
Ethernet interface: RJ45 interface, TCP/IP protocol, the network connection
between the PC and the printer can be realized through this interface USB
interface: USB-B type interface, directly connected to the PC.
Power interface: connect to AC power 100-240VAC, 50/60Hz, 4A.
Power switch: turn on and off the card printer circuit.
Back-end output card port: The printed card is ejected from here, support
manual feeding card on back-end and recycling pending card.
1.3 Front-end View
Input hopper: Blank card storage area, capacity: 200pcs standard
card(0.76mm).
Defective card slot: Defective cards storage area, capacity: 25pcs
standard card(0.76mm).
Unpacking Inspection
Check whether the appearance is intact after opening the outer box, and check whether the accessories are complete according to the product instruction manual (prevailed by the sales contract). If there is any missing, please contact the dealer to communicate and solve.
Install Accessories and Consumables
3.1 Install Cleaning Module (Top)
- Take out the cleaning module and cleaning roller from the accessory boxof the card printer, and assemble them as shown in the picture below. After tearing off the 3M adhesive layer, hold the two ends of the cleaning roller with your hands, push them to the installation position and gently press down to lock the two ends of the cleaning roller.
- Press the red frame part of the upper door in the below left picture, open the upper door after the upper door lock pops out.
- Install the assembled cleaning module above (press vertically) into the card printer as shown in the picture below:
3.2 Install the Input Hopper
First take out the input hopper from the accessory box, turn 90° to open the
card foundation, and then press the slot to the end vertically as shown in the
picture below
3.3 Install the Output Hopper
Take out the output hopper from the accessory box. There are two holesunder
the card outlet at the back of the card printer. Insert the card slot hooks
intothe two holes below the card outlet as shown in the picture below.
3.4 Consumables Installation
Take out the ribbon and transfer film from the consumable packaging box, open
the corresponding blister boxes respectively and take out the ribbon and
transfer film.
-
Remove the Consumables Holder
Pull the ribbon door ring as shown below, open the ribbon door, turn the handle of the consumable holder, and take out the consumable holder. Warning : When card printer shipped from the factory, there will be placed a piece of sponge paper next to the print head, please take it off before use or the power on test, otherwise it may cause damage to the printhead. Operation steps are as follows.
As shown in the picture below, follow the operating guidelines to remove the right ribbon holder, and then remove the sponge paper as shown. -
Install the Ribbon and Transfer Film
Install the transfer film and ribbon into the consumable holder as shown below.
Hardware Connections
Take out the power cable and USB data cable from the accessory box of the card printer’s outer packing box. The USB-A type interface is connected to the computer, and the USB-B type interface is connected to the USB interface of the printer. Ethernet communication interface installation: RJ45 network interface ,568B connection mode. Note: support USB and Ethernet communication interface. It’s recommended that to choose one of them.
Install Cards and Place the Counterweight Card
5.1 Introduction of Using the Input Hopper
Press the yellow button in the card input hopper and turn the door cover 90°to
open the hopper door as shown in the picture below. 5.2 Install Cards
You can put cards into the input hopper after the card printer installation is
completed.
- There is no requirement for the direction of contactless IC cards and ordinary white cards, the card insertion direction can be customized according to needs.
- The contact IC card should be inserted strictly in accordance with the card direction in the picture below, which is consistent with the ATM card insertion rules. If you only need to print and don’t need to encode chip data, there is no requirement for the direction of the card. The card insertion direction can be customized according to needs.
- ISO7811 standard magnetic stripe card should be inserted strictly in accordance with the card direction in the picture below, which is consistent with the ATM card insertion rules. If you only need to print and don’t need to encode chip data, there is no requirement for the direction of the card. The card insertion direction can be customized according to needs.
5.3 Place Counterweight Card
Take out the counterweight card from the accessory box after installing the
card and place it in the card slot. Counterweight card: Apply gravity to
the card to ensure stable card insertion when the number of cards in the card
slot is small.
Note: If you need to understand the operation requirements of card input
from the back, please refer to the product manual of the corresponding model.
This manual will not explain it in detail.
Print Test
6.1 Install the Driver
Download the installation package from the CD in the accessory box or the
company’s official website www.seaory.com. And
install the driver according to the software installation process prompts or
the product instruction manual of this model
6.2 Print Test
-
Driver Test Page
Step 1: In the list of printers and devices → right-click the Seaory R300 printer icon → printer properties. Step 2: After enter below picture interface, place some white card into input hopper, then click” Print Test Chart” Step 3: When print out the following card, that’s mean the driver program and hardware installation are normal. -
Seaory iCARDE Card Design Software
After all the above steps are completed, relevant software can be used to print and test the card printer. You can also do print test through Seaory’s iCARDE software. For details, please refer to Seaory iCARDE manual.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>