HILTI HIT-CT 1 Injectable Adhesive Anchor Instruction Manual
- June 3, 2024
- HILTI
Table of Contents
HILTI HIT-CT 1 Injectable Adhesive Anchor
Read the safety instructions and product information before using the product.
Instruction for use
| Contains: dibenzoyl peroxide (B) Toxic to aquatic life with long lasting
effects.(B)
Do not get in eyes, on skin, or on clothing.
IF ON SKIN: Wash with plenty of water.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing.
---|---
| Contains dibenzoyl peroxide. May produce an allergic reaction.
---|---
Dry concrete
|
Water saturated concrete
|
Waterfilled borehole in concrete
|
Submerged borehole in concrete
|
Hammer drilling
---|---|---|---|---
Hollow drill bit
|
Uncracked concrete
|
Cracked concrete
---|---|---
Temperature of concrete
|
Working time
|
Curing time
⌀ d [mm]
| ⌀ d0 [mm]| hef std [mm]| hef [mm]| ⌀ df [mm]| Tinst [Nm]
---|---|---|---|---|---
M8| 10| 80| 64…96| 9| ≤ 10
M10| 12| 90| 80…120| 12| ≤ 20
M12| 14| 110| 96…144| 14| ≤ 40
M16| 18| 125| 128…192| 18| ≤ 80
M20| 22| 170| 160…240| 22| ≤ 150
M24| 28| 210| 192…288| 26| ≤ 200
⌀ d [mm]
|
⌀ d0 [mm]
|
hef [mm]
---|---|---
8| 10| 64…250
12| 64…700
10| 12| 80…250
14| 80…700
12| 14| 96…250
16| 96…700
14| 18| 112…700
16| 20| 128…700
18| 22| 144…500
20| 25| 160…500
22| 28| 176…500
24| 32| 192…500
25| 32| 200…500
Adhesive anchoring system for rebar and anchor fastenings in concrete
▶ Prior to use of product, follow the instructions for use and the safety
precautions.
Hilti HIT-CT 1
Contains: Dibenzoylperoxid (B)
| H411 Toxic to aquatic life with
long lasting effects.
P262 Do not get in eyes, on skin or on clothing
P302+P352 IF ON SKIN: Wash with plenty of water.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do. Continue rinsing.
EUH208 Contains dibenzoyl peroxide. May produce an allergic reaction.
---|---
Disposal considerations
Empty packs:
- Leave the mixer attached and dispose of via the local Green Dot recovery system
- or EAK waste material code: 150102 plastic packaging
Full or partially emptied packs:
- Must be disposed of as special waste in accordance with official regulations.
- EAK waste material code: 08 04 09* waste adhesives and sealants containing organic solvents or other dangerous substances.
- or EAK waste material code: 20 01 27* paint, inks, adhesives and resins containing dangerous substances.
Content : 330 ml / 11.1 fl. oz 500 ml / 16.9 fl. oz
Weight : 600 g/21.1 oz 910 g/32.1 oz
Hilti accepts no liability for damage or failure caused by:
- Storage and transport not in accordance with the specified conditions
- Failure to observe the instructions for use and setting data
- Inadequate design of the anchor points
- Inadequate load bearing capacity of the base material
- Incorrect use
- Other influences of which Hilti is not aware or on which Hilti has no influence, e.g. use with products from a third party
Product Information
- Always keep these instructions together with the product even when given to other persons.
- Check expiration date: See imprint on foil pack manifold (month/year). Do not use expired product.
- Foil pack temperature during usage: 5 °C to 40 °C / 41 °F to 104 °F.
- Base material temperature at time of installation: -5 °C to 40 °C / 23 °F to 104 °F.
- Conditions for transport and storage: Keep in a cool, dry and dark place between 5 °C and 25 °C / 41 °F and 77 °F.
- For any application not covered by this document / beyond values specified, please contact Hilti.
- Partly used foil packs must be used up within 4 weeks. Leave the mixer attached on the foil pack manifold and store under the recommended storage conditions. If reused, attach a new mixer and discard the initial quantity of anchor adhesive. A new mixer must be used for each new foil pack.
Improper handling may cause mortar splashes.
- We recommend to wear safety glasses, gloves and protective clothes during installation.
- Never start dispensing without a mixer properly screwed on.
- Attach a new mixer prior to dispensing a new foil pack (ensure snug fit).
- Use only the type of mixer supplied with the adhesive. Do not modify the mixer in any way.
- Never use damaged foil packs and/or damaged or unclean foil pack holders (cassettes).
Poor load values / potential failure of fastening points due to inadequate borehole cleaning.
- Hilti hollow drill bits TE-CD, TE-YD must be used in conjunction with a properly maintained Hilti vacuum cleaner with model and suction capacity (volumetric flow rate) as specified in the accessory table.
- The boreholes must be free of debris, dust, water, ice, oil, grease and other contaminants prior to adhesive injection.
- For blowing out the borehole – blow out with oil free air untilreturn air stream is free of noticeable dust.
- Important! Remove all water from the borehole and blow out with oil free compressed air until borehole is completely dried before mortar injection.
- For brushing the borehole – only use specified wire brush. The brush must resist insertion into the borehole – if not the brush is too small and must be replaced.
Not adhering to these setting instructions can result in failure of fastening points!
21
Hilti AG
FL-9494 Schaan
Hilti Werke
2873-CPR-201-28
ETA-11/0354
Notified body 2873
EAD 330499-01-0601
www.hilti.group
Made in Germany
Hilti = registered trademark of Hilti Corporation, Schaan, Liechtenstein
www.hilti.group
© 2022
Right of technical changes reserved S.E. & O.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>