ALESIS DRUMS Strike Amp 12 Powered Drum Amplifier Cable Kit User Guide

: June 3, 2024
: ALESIS DRUMS

Table of Contents

Introduction
Box Contents
Support
Setup
Features
- Rear Panel
Appendix
- Technical Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ALESIS DRUMS Strike Amp 12 Powered Drum Amplifier Cable Kit

Introduction

Thank you for purchasing the Strike Amp 12. At Alesis Drums, we know how serious music is to you. That’s why we design our equipment with only one thing in mind—to make your performance the best it can be.

Box Contents

Strike Amp 12
Power Cable
User Guide
Safety & Warranty Manual

Support

For the latest information about this product (documentation, technical specifications, system requirements, compatibility information, etc.) and product registration, visit alesis.com.
For additional product support, visit alesis.com/support.

Setup

Items not listed under Introduction > Box Contents are sold separately.

Example A: One Strike Amp 12 (Mono)

Connect the Left (Mono) output of your drum module to the input on a Strike Amp 12.

Example B: Two Strike Amp 12s (Stereo)

Connect the Right and Left (Mono) outputs of your drum module to the inputs of your Strike Amp 12s.

Example C: Two Strike Amp 12s (Mono)

Connect the Left (Mono) output of your drum module to the input of one Strike Amp 12, and then connect the output of that Strike Amp 12 to the input of another.

Features

Rear Panel

AC Input: Use the included power cable to connect this input to a power outlet. Make sure the Power Switch is set to off when connecting or disconnecting the cable.
Fuse: If the unit’s fuse is broken, lift this tab to replace the fuse. Replace it with a fuse with an appropriate rating (printed under the unit’s power cable input).Using a fuse with an incorrect rating can damage the unit and/or fuse.
Power Switch: Use this switch to power the loudspeaker on or off. Make sure the Volume knob is set to its minimum (counterclockwise) position before turning it on
Power LED : This LED lights up when the loudspeaker is on.
Volume : Turn each knob to adjust the volume of each input.
Input: Use a standard XLR cable or 1/4” (6.35 mm) TRS cable (not included) to connect your audio source to this input.
Output: Use a standard XLR cable (not included) to connect this output to the input of another loudspeaker (i.e., another Strike Amp 12).
Signal Limit LED : This LED lights up green when an audio signal is sent to the loudspeaker—it flashes at lower levels and lights solidly at higher levels. The LED lights up red when output limit/protection is active—if the LED is lit red continuously, reduce the volume of your audio source.
Contour: Engage (depress) this button to emphasize low and high frequencies by +3 dB. Disengage (raise) the switch for a flatter response for live performance or for maximum output.
. Ground Switch : Engage (depress) this switch to reduce hum or noise.

Appendix

Technical Specifications

Output Power 2000 W (peak, 1300 LF + 700 HF)

1000 W (continuous RMS, 650 LF + 350 HF)

Drivers| Low-Frequency 12.0” (305 mm) low-frequency driver, 3.0” (76 mm) high-temperature voice coil
High-Frequency 1.4” (35 mm) voice coil, neodymium-magnet high-frequency driver with precision waveguide
Crossover Frequency| 2.0 KHz
Maximum SPL| 131 dB (peak), 128 dB (continuous) (dB-SPL @ 1 m)
Frequency Response| 53 Hz – 20 kHz (+3 dB)
Frequency Range| 46 Hz – 22 kHz (-10 dB)
Horn Coverage| 90º horizontal x 60º vertical (nominal)
Equalization| Contour switch with low- and high-frequency +3 dB boost
Connectors| (2) XLR/TRS 1/4” (6.35 mm) combo inputs
(1) XLR link output
(1) IEC power cable input
Controls| Power switch, (2) volume control knobs (1 per input), EQ contour switch, ground-lift switch
Indicators| (2) power LEDs (1 front-panel, 1 rear-panel), clip limiter LED
Protection| Electronic clip, thermal & transducer overdrive
Power| Connection| IEC
Input Voltage| 100 V~, 110–120 V~, 220–240 V~; 50/60 Hz (switchable)
Fuse| 100–120V T10AL AC250V
220–240V T5AL AC250V
Consumption| 800 W
Enclosure| Trapezoidal, injection-molded polypropylene enclosure with perforated steel grille
Dimensions