evolur AI-847 Toddler Guard Rail Instruction Manual

evolur AI-847 Toddler Guard Rail

ASSEMBLY INSTRUCTIONS

Adult assembly is required. Small parts may present a choking hazard prior to assembly.

Enclosed please find simple step-by-step instructions to help you quickly assemble your product. Before you begin, we recommend that you follow the steps below:

1. Please read the instructions thoroughly
2. identify all parts and hardware
3. You may need to provide the following tools:
   • .Philips Head screwdriver
   • Flat head screwdriver
   • Hammer

Do Not Use Power Drills Or Drivers

lo protect your parts during assembly please please place them on a soft surface. lo clean surface, use only water on a damp cloth. Do not use window cleaner or cleaning abrasive as it will scratch the surface and could damage the protective coating.

Furniture Care Instructions

Room Climate Control

Wood, when the first cut contains more than 50 percent water. When it is prepared for furniture construction it is placed in a Kiln and the moisture content is brought down to 8 to 10 percent. Wood is porous and responds to its environment. If the room has high humidity it will absorb it and expand and if the humidity is low it will lose moisture and shrink. It is important that the humidity levels in the room be controlled from extremes of too much humidity or too little. Furniture should not be placed close to air-conditioning outlets, fireplaces, radiators, space heaters, humidifiers or dehumidifiers. Exposure to extreme variations of temperature and humidity can damage any fine wood product.

The Ideal Environment for Fine Furniture

Fine wood furniture will have fewer problems when its environment is controlled at a temperature between 65 and 75 degrees and relative humidity between 35 and 40 percent. Wood placed in an environment outside of those limits can and will shrink or expand and may develop some small cracks which are not material or structural defects.

Avoid Direct Sunlight

Keep the furniture out of direct sunlight. Ultraviolet rays will fade colors and in some cases darken them. It can also cause erasing or hair line cracks in the finish. White finishes will yellow naturally over time and exposure to direct sunlight will hasten this natural process along with some woods darkening naturally over time; this is not considered to be a quality defect.

Proper Storage

If you need to put your furniture in storage for any period of time do not store them in a damp basement or hot dry attic. Allow air movement around the furniture and do not stack anything on it.

In General

• Protect furniture surface from hot or extremely cold items. U
• se coasters under hot or cold beverages
• Do not use synthetic fabric under accessories or lamps
• Protect tops from pens, makers and crayons
• Oils from potpourri and other seented items can damage the furniture finish.
• Do not drag items across the surface of the furniture.
• Allow the surface to breath by rotating your accessories and lamps.
• Do not over polish the furniture, do it only two or three times a year. Over-polishing can distort the natural finish of the product.
• Do not wax the furniture as wax build-up can destroy the natural finish of the product
• When moving furniture always lift the unit. Do not push or drag it to avoid damage to the legs
• Keep the furniture level so doors and drawers open and close freely.
• Clean with a damp, not wet, cloth. Use only a mild soap. Do not use abrasive cleaners.

HARDWARE AND TOOL DIAGRAM

PARTS ENCLOSED IN CARTON

STEP 1

REMOVE FOOTBOARD

Model shown is example only. Styles may vary.

STEP 2

ASSEMBLE STABILIER BAR

Model shown is example only. Styles may vary.

STEP 3

ASSEMBLE GUARD RAIL

WARNING

WHEN CONVERTING THIS CRIB TO A TODDLER BED, A GUARD RAIL AND STABILIZER BAR MANUFACTURED BY ÉVOLUR INC., MUST BE USED.

In order to convert your crib to a toddler bed, you must first remove the front rail of the crib, then attach the guard rail using the bolts from the front rail removal.

NOTE: Make sure the mattress support is in the lowest position. Please follow the complete instructions that come with the guard rail which is sold separately.

WARNING!

For Toddler Beds Use

• FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH FROM ENTRAPMENT OR STRANGULATION.
• DO NOT PLACE THE BED NEAR WINDOWS WHERE CORDS FROM BLINDS OR DRAPES MAY STRANGLE A CHILD.
• THE MATTRESS INTENDED FOR USE ON THIS BED SHALL BE A FULL-SIZE CRIB MATTRESS HAVING THE DIMENSIONS OF 51-5/8 IN (1310 MM) IN LENGTH AND 27-1/4 IN (690 MM) IN WIDTH AND THICKNESS OF 4 IN (100 MM) OR A GREATER THICKNESS AS SPECIFIED BY THE MANUFACTURER.
• THE MINIMUM AGE OF THE INTENDED USER SHALL NOT BE LESS THAN 15 MONTHS AND THE MAXIMUM WEIGHT SHALL NOT BE GREATER THAN 50 LBS. (22.7 KG).

Day Bed Conversion

WARNING
WHEN CONVERTING THIS CRIB TO A DAY BED,A  STABILIZER BAR MANUFACTURED BY ÉVOLUR INC., MUST BE USED. In order to convert your crib to a day bed, you must first remove the front rail of the crib, then attach the stabilizer bar, using the bolts from the front rail removal.
NOTE: Make sure the mattress support is in the lowest position. Please follow the complete instructions that come with the guard rail which is sold separately.

EVOLUR – 1532 S. WASHINGTON AVE, PISCATANAY, NJ 08854, Tel: 732-752-7220

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>