Kentec Electronics DNX-A-2R-K Intelligent Network Solutions User Guide
- June 4, 2024
- Kentec Electronics
Table of Contents
Kentec Electronics DNX-A-2R-K Intelligent Network Solutions
Safety
Suppliers of articles for use at work are required under section 6 of the
Health and Safety at Work Act 1974 to ensure as reasonably as is practical
that the article will be safe and without risk to health when properly used.
An article is not regarded as properly used if it is used ‘without regard to
any relevant information or advice’ relating to its use made available by the
supplier.
This product should be installed, commissioned and maintained by trained
service personnel in accordance with the following:
- Regulations for electrical equipment in buildings specific to the country of use.
- Codes of practice
- Statutory requirements
- Any instructions advised by the manufacturer.
Installers of this product are required to take such steps as necessary to
ensure that all appropriate information and training is provided to anyone
concerned with its use.
This equipment is designed to operate at a DC voltage of 18-36V and therefore
will require a separate power supply.
Any power supplies used with this equipment must be suitably approved to the
required local standards and must be installed following the relevant
electrical, installation standards and manufacturers’ recommendations.
This unit should be built into an apparatus cabinet, or similar, where access
is restricted to service personnel only.
This unit uses convection cooling. Avoid obstructing the airflow around the
unit.
This equipment is certified as environmental class A and therefore designed
for indoor use only at temperatures between -10°C and +70°C with a maximum
relative humidity of 95%. The IP rating for the enclosure is IP20
Operation outside of these limits may render the equipment unsafe.
iNS Quick Start Guide
This Start Guide provides iNS module connection/settings overview and links to the product range User Guides.
Important! Information in this Start Guide is supplementary.
The product Installation Manual and Operation Manual should read, understood
and referred to throughout.
QR Codes
The QR codes below provide links to iNS User Manuals. Using your Smartphone,
tablet or device (where necessary) install a third party QR Code Reader and
scan the code to open the documents.
Reading the QR Codes
Should you be unable to work with QR codes Manuals can be obtained by visiting the following website pages:
| Manual Variant | Website |
|---|---|
| DNX-A-2R-K User Guide | http://www.kentec.co.uk/manuals/man-1491.pdf |
| DNP-R-2F/FC-K User Guide |
http://www.kentec.co.uk/manuals/man-1572.pdf
DNX-A-2R-K Dual Port Fire Alarm Control Panel Connections & Selection
Settings
DNP-R-2F/FC-K Dual Port Fire Alarm Control Panel Fibre Connections & Passive
Mode Settings
DNP-R-2F/FC-K Dual Port Fire Alarm Control Panel Fibre/RS485 Connections &
Selection Settings
Terms and Conditions
Details of Kentec Electronics Ltd. Terms and Conditions including Warranties
and Returns & Repair Policies can be found on our website at the following
locations:
Terms, Conditions & Warranty https://kentec.co.uk/terms-and-conditions/
Returns & Repairs http://www.kentec.co.uk/returns-and-repairs/
Address of Kentec Electronics Ltd.
Units 25-26 Fawkes Avenue,
Questor, Dartford,
Kent. DA1 1JQ
United Kingdom
Registered in England: FACP
No.1937570
Tel: +44 (0)1322 222121
http://www.kentec.co.uk
Disclaimer
In no event shall The Manufacturer be liable for any damages or injury of any nature or kind, no matter how caused, that arise from the use of the equipment referred to in this manual. Strict compliance with the safety procedures set out and referred to in this manual, and extreme care in the handling or use of the equipment, are essential to avoid or minimize the chance of personal injury or damage to the equipment. The information, figures, illustrations, tables, specifications, and schematics contained in this manual are believed to be correct and accurate as at the date of publication or revision. However, no representation or warranty with respect to such correctness or accuracy is given or implied and The Manufacturer will not, under any circumstances, be liable to any person or corporation for any loss or damages incurred in connection with the use of this manual.
The information, figures, illustrations, tables, specifications, and schematics contained in this manual are subject to change without notice. Unauthorized modifications to the fire detection system or its installation are not permitted, as these may give rise to unacceptable health and safety hazards. By installing this equipment on a computer network, the owner accepts full and unequivocal responsibility for ensuring that it is protected against all cyber threats and illegal tampering during the lifetime of the equipment. Any software forming part of this equipment should be used only for the purposes for which The Company supplied it. The user shall undertake no changes, modifications, conversions, translations into another computer language, or copies (except for a nec-essary backup copy). In no event shall The Manufacturer be liable for any equipment malfunction or damages whatsoever, includ-ing (without limitation) incidental, direct, indirect, special, and consequential damages, damages for loss of business profits, business interruption, loss of business information, or other pecuniary loss, resulting from any violation of the above prohibitions.
References
- Home - Kentec Electronics Ltd
- Returns Policy - Kentec Electronics Ltd
- Terms and Conditions - Kentec Electronics Ltd
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>