perle IRG7440 5G Cellular Router User Guide

perle IRG7440 5G Cellular Router User Guide

This guide covers the basic installation and configuration of the IRG7440 5G Cellular Router and is intended for firsttime setup or product evaluation.

Complete details can be found in the following guides at www.perle.com/downloads.

• IRG7440 5G Cellular Router Hardware Installation Guide
• IRG7000/5000 5G/LTE Router User’s Guide
• IRG7000/5000 5G/LTE Router Command Line Interface Reference Guide

What’s in the box?

The following components may be included with your product. Components will vary depending on each model.
See the Perle website for updates

• IRG7440 5G Cellular Router
• IRG7440 5G Cellular Router Quick Start Guide (this guide)
• 5G/LTE SMA antenna pack-4 (#08000530)
• GPIO Cable with 4 pin plug (#2500468)
• GPIO Cable with 8 pin plug (#2500476)
• 12VDC/2A 4 pin (NA#08000150, EU #08000160, UK #08000170, AUS#08000180)
• Orderable–GNSS PAV RP Antenna SMA/CA (#08000130) passive
• Orderable–DIN Rail mounting kit (orderable from Perle)

Getting Started

Typical installation steps are:

1. Inserting the SIM card.
2. Connecting 5G/LTE antenna/s.
3. Connecting the Power.
4. Connecting to the Cellular Network.
5. Fast Setup Mode.

Inserting the SIM card

Use only a mini-SIM (2FF) card.
Ensure the power is disconnected before you insert the SIM card.

1. Unscrew the screws and gently pry the SIM cover loose from the opening (see below).
2. Align the SIM card so that the SIM card will slide into the SIM slot, ensuring that the SIM card connectors will be facing the router’s printed circuit board (face down).
3. Align the SIM cover plate and secure the plate with the screws.

Connecting the 5G/LTE Antennas

1. Connect an antenna to the connector Main.
2. Connect an antenna to the connector MIM01.
3.  Connect an antenna to the connector MIM02.
4. Connect an antenna to the connector DIV/GNSS L1.
   See Figure 2
   
   

Connecting the Power

See Figure 2 for wiring requirements. The colors indicated are for the Perle supplied DC cable.

Connecting to the Cellular Network

When the router is powered on, it begins activating and attempting to connect to the cellular network. This process typically takes a few minutes. A solid green WWAN LED indicates a successful connection; if not, see the IRG7440 5G Cellular Router Hardware Installation Guide for details.

Fast Setup Mode

Fast Setup provides a simple method of doing an initial setup from a PC. Your router is shipped in factory default mode.

1. Your PC must be set to obtain an IP address automatically using DHCP.

2. Plug the PC into your router’s Ethernet interface.

3. When the Power LED is flashing green, use a web browser, enter http://192.168.0.1 to access your router. On the setup screen, select, Getting Started.
   

4. Once connected, fill in the required fields, apply changes to save and exit. Your configuration changes will be immediately applied to the router

5. The router’s web configuration sign-on screen will be displayed. Using the credentials you previously defined in Step 4, you can now access your router’s full configuration.

For alternative methods of performing and initial Setup, see the IRG7440 5G Cellular Router Hardware Installation Guide.

© 2022 Perle Systems Limited. All rights reserved.

Documents / Resources

| perle IRG7440 5G Cellular Router [pdf] User Guide
IRG7440 5G Cellular Router, IRG7440, IRG7440 Router, 5G Cellular Router, Cellular Router, 5G Router, Router
---|---

References

• Perle | device networking, media conversion, & IoT connectivity

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>