perle SCR1618 Secure Out of Band Management Console Server User Guide
- June 6, 2024
- perle
Table of Contents
IOLAN SCR1618 RDAC
Quick Start Guide
This guide covers basic installation and configuration and is intended for first-time setup or product evaluation.
Complete details can be found in the following guides at www.perle.com/downloads.
- IOLAN SCR User’s Guide
- IOLAN SCR Command Line Reference Guide
- IOLAN SCR1618 RDAC Hardware Installation Guide
What’s in the box?
-
IOLAN SCR Chassis
√ 16 RS232 RJ45 Ethernet ports
√ 16 RS232 serial RJ45 ports -
Quick Start Guide (this guide)
-
Rack Mount Kit
What’s you need to supply
- Serial cables to connect serial devices to your IOLAN
- Ethernet CAT5e 10/100/1000BASE-T cables to connect Ethernet devices to your IOLAN
Setting up the IOLAN SCR
- Connecting dual or single power to the IOLAN SCR.
- Configuring the IOLAN SCR.
- Connecting Ethernet devices.
- Connecting Serial devices.
IOLAN SCR1618 RDAC Quick Start Guide - 5500463-11 (Rev B)
Version #A06.23.2021
SCR Front View
- Power Switch/s
- PWR LEDs
- LEDs 1 and 2
- Ethernet 18 and 17
- Admin
SCR Back View
- Serial Ports (1-16)
- Ethernet Ports 1-18
- Dual AC Power Supplies
- Reset
- Ethernet Ports
- Serial Ports
LEDs
PWR 1 (Power 1)
PWR 2 (Power 2)| Solid green
Solid green| Power available for this power supply
Power available for this power supply
---|---|---
| Off
Off| No Power connected
No Power connected
LED1| Solid green
Flashing green| System is ready for Normal Operation
No startup-config
LED2| | No valid IP health configured or active
Solid green| WAN high-availability mode = Failover
Wan failover interface with the highest priority (primary) is ACTIVE
WAN-high-availability mode = Load-share
All load-sharing WAN interfaces are ACTIVE
Blinking green| All interfaces with IP health configured, are active
Ethernet 17 / SFP
Ethernet 18 / SFP| Solid green or flashing
Solid green or flashing| Link up / Link activity
Link up / Link activity
Connecting the Power
Connect 1 or 2 power to power sources. Once power is connected, the IOLAN will cycle through several sequences. The LED 1, PWR 1 and 2 will show solid green when the IOLAN is fully booted and ready to configure. If dual power is used, then both PWR LEDs and LEDs 1 and 2 will be lit.
Setup Mode
Setup Mode provides a simple method of doing an initial setup from a PC. Your IOLAN is shipped in factory default mode. Setup Mode can also be accessed through the console port; see your IOLAN SCR1618 RDAC Hardware Installation Guide for more details.
- Complete the Connecting the Power step.
- Set your PC to obtain an IP address automatically using DHCP.
- Plug your PC into any of the IOLAN’s Ethernet ports (located on the back of the unit).
- Use a standard web browser to enter http://192.168.0.1 to access your IOLAN.
On the setup screen, select, Getting Started.
5. Once connected, fill in the required fields, apply changes to save and
exit. The configuration changes are immediately applied to the IOLAN.
6. The IOLAN’s web configuration sign-on screen is displayed. Using the
credentials you previously defined in Step 4, you can now access your IOLAN’s
full configuration.
Connecting Ethernet Devices
The Ethernet RJ45 ports provide the standard Ethernet interface speeds of 10/100/1000 Mbps. By default, all 10/100/1000 Ethernet ports will automatically set themselves up to match the speeds of attached devices.
Ethernet Port
| Left Hand | Right Hand | Description |
|---|---|---|
| N/A | Amber | 1000 Mbps/flashes with activity |
| Amber | Green | 100 Mbps/flashes with activity |
| Green | N/A | 10 Mbps /flashes with activity |
| Off | Off | No Lan connection |
Connecting Serial Devices
Connect devices, workstations, servers or routers using a straight through serial cable.
| Pinout | Direction | EIA-232 |
|---|---|---|
| 1 | in | CTS |
| 2 | in | DSR |
| 3 | in | RxD |
| 4 | GND | |
| 5 | GND | |
| 6 | out | TxD |
| 7 | out | DTR |
| 8 | out | RTS |
SFP Ports
The following SFPs are supported 1 Gbps fiber, 2.5 Gbps fiber and SGMII copper.
Connecting the Fiber
Ensure that the cable implements the proper TX to RX crossover. Once the device is connected and the link is established the corresponding SFP LED will turn green.
© 2021 Perle Systems Limited. All rights reserved.
Documents / Resources
|
perle SCR1618 Secure Out of Band Management Console
Server
[pdf] User Guide
SCR1618, Secure Out of Band Management Console Server, SCR1618 Secure Out of
Band Management Console Server, Out of Band Management Console Server,
Management Console Server, Console Server
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>