ECHTPOWER Joy Pad Controller User Manual
- June 3, 2024
- ECHTPOWER
Table of Contents
ECHTPOWER Joy Pad Controller
OVERVIEW
Product Descriptiont
The Joy-pad Bluetooth wireless controller is the standard controller of the
Nintendo Switch. It can be connected to the main screen through the slide rail
to play, or it can be used wirelessly without the slide rail. It has the
functions of a normal controller, In some specific games, the Joy-pad also I
is allowed to use a single controller in the horizontal direction, and some
game Joy-pads can be held tightly with both hands to become a somatosensory
controller, Joy-Pad is equipped with motor vibration and 6-axis functions, and
the joystick has cool ambient lights, allowing you to be immersed in the game.
The joy-pad has a wake-up function, no NFC function, no infrared camera, no
air upgrade, only support local upgrade package to upgrade.
Product Parameters
- Color: black
- B 109.2965.38″54 4650mm (single)
- Joy-pad weight: bare metal 174g (2 pieces)
- BABS environmental protection material
- Transmission medium: Bluetooth 2.1
- Carrier frequency: 2.402-2.480GHz
- Protocol: Bluetooth BT2.1+EDR (Only support BT ETR)
- LED: 8 monochrome LEDs, 6 Symphony LEDs (one pair)
- Pairing: After the handle enters the pairing mode, it will automaticaly sleep if the pairing is not successful within 2.5 minutes
- Battery: one polymer lithium battery 3.7V/500mAH on the left and right
- Endurance time: 6.5 hours of continuous work when fully charged (the usage time when the lights are not turned on)
- Working voltage: 3,7V4,2V
- Charging voltage: 5V
- Temperature cycle and high and low temperature work requirements: -10 C-50 c
- Required storage temperature: -20 C-70C
- Drop test height: 1.2m, 6 faces, 2 cycles, marble floor
- Button force: Silicone button force is 160g, touch switch force is 160g
- Key life: (ABXY, direction keys, L2, R2 keys) silicone keys 500,000 times, L, R, Home, Camera, +,- T keys 100,000 times
Connection method
Please do not touch the joystick during the connection of Joy-pad, and keep the joy-pad still for more than 5 seconds after the connection is successful, which can prevent the phenomenon of drifting during the game.
Operation guide
- Left and right resolution: The Joy-pad is facing up. the Joy-pad with the ” key on the upper right is installed on the left side of the NS console, and the Joy-pad with the “+” button on the upper left is installed on the right side of the NS console,
- Connect the Joy-pad to the NS console: the side with “+” and “”is up, along the slide rails on both sides of the console screen, slide the Joy-pad from top to bottom until a clicking sound is heard, which means the installation is successful.
- Remove the Joy-pad from the device: Find the unlock button on the top of the back of the Joy-pad. press and hold the unlock button and slide the Joy-pad from bottom to top until the Joy-pad is completely separated from the device, then release the unlock button.
Connecting to use
DFirst connection
Method 1: Install the two joy-pads in the slide rails on both sides of
the main screen, slide the Joy-pad from top to bottom until a clicking sound
is heard, and the console will have an icon to indicate that the connection is
successful. When the joy-pad is removed, it will be automatically connected to
the console,
Note: One console can log in up to 6 control devices, and one Joy-pad is
equivalent to one control device.
Method 2: 1. Press the power button on the console to enter the interface 2. Perform the following operations: Click “Controllers”- “Change Grip/Order” after entering this interface, press the pairing button on the two joy-pads for more than 2s Connect, at this time, the 4 LEDs flash as marquee lights. After the connection is successful, the indicator light of the corresponding player is always on, Press the L+R key to use.
Connect again
Method 1: When the Joy-pad is installed in the slide rails on both sides
of the console screen and needs to wake up the console, press the joy-pad HOME
button to wake up the console
Method 2: When the Joy-pad is separated from the console, and the console
is in the sleep state, long press the camera button and the HOME button of the
left and right Joy-Con handles for 1-2 seconds to wake up the two joy-pads,
and the four LEDs run quickly. Blinking connected to the Console
Automatic sleep
When the Joy-pad is installed on the console, the screen of the console is turned off, and the Joy-pad automatically sleeps, After the console sleeps, press the HOME button of the joy-pad to wake up the console, When the Joy-pad is separated from the console, if there is no operation within 5 minutes, the Joy-pad will automatically sleep.
Charging instruction
Turn off and charge: The 4 LED indicators flash slowly, and the indicators
will turn off when fully charged.
Play while charging mode: the corresponding channel indicator flashes slowly
and turns solid when fully charged.
TURBO function
- Press TURBO key+A/B/XYIL1/L2/R1/R2/cross key to set TURBO function
- Press TURBO key+A/B/XYIL1/L2/R1/R2/cross key again to set Auto TURBO function.
- Press the TURBO key + A/B/XYIL1/L2/R1/R2/cross key for the third time to clear the TURBO function.
Note: Press the button with the set TURBO function to have a vibration indication, and the corresponding TURBO button function can only be set to the corresponding handle button. Long press the single TURBO button for 5 seconds (with vibration prompt) to clear all TURBO button functions OTURBO speed adjustment (there are three speeds that can be adjusted) Left handle adjustment method: Press the TURBO button and the ” button, press the speed to increase by one gear, and adjust three gears, and cycle in turn Right handle adjustment method: Press the TURBO button and the “+” button, press the speed to increase by one gear, and adjust three gears, and cycle in turn
Back key function
-
Macro programming programmable keys: 2 joysticks, L3, R3, cross keys, ABXY, L, R, ZL, ZR, +” key, “-” key.
-
Press and hold the M key of the setting key to enter the macro programming (4 indicator lights are always on), then press the key you want to set (you can press one or more, you can press it at the same time or in sequence), and press the key you want to set. After pressing the button, release the setting button to indicate that the setting is complete (there will be a vibration prompt). The programming key will store the previous operation. Press the programming key next time to trigger the stored operation, which can be used to set up combos in the game.
-
For example: Press and hold the M key (4 LEDs are on at the same time, do not let go of the M key that is held down)+ B key, then press the A key every one second, and then press the X key every two seconds, release the M key after the setting is complete Press the key to save and exit (vibration prompt). At this time, the function of pressing the MR key is to copy the key pressed just now: B interval 1 second A interval 2 seconds X.
Note:
- Left M key: Only set the programmable key of the left handle.
- Right M key: Only set the programmable keys of the right handle. The controller can be powered off and restarted to clear the set macro programming.
Motor strong and weak vibration adjustment function
Press and hold the back vibration button to adjust the vibration intensity of the motor (the left and right handles can be used as separate handles to adjust the vibration, and the vibration intensity can be cycled in turn). There are five intensities in total, 100%, 75%, 50%, 25%, 0%.
Ambient light adjustment
- T+ (dick) R3/L3: Monochromatic light long-bright mode, the overall light color changes to one click to change a color, the order: redlyellow/blue/green/purplelorange/white/magic color, cyclic change.
- T+ (double click) R3/L3: breathing mode;
- First time: RGB seven-color breath
- The second time: LED magic color breathing:
- Third time: turn off the lights.
Light brghtness adjustment: 1+ rocker up buton can increase the handle ight brightness, T+ rocker down button can reduce the handle light
Handle hardware reset
Keep pressing the HOME button for more than 10 seconds to reset the controller nardware,
Handle back connection
When the handle matches the previous device, after the handle is in standby, you only need to press the HOME button/photograph button to connect back to the previous device.
Correction
When using it for the first time, you need to calibrate the joystick and gyro Sensor on the console after connecting to the console. Bridge—Handle Connector (English: Controller Connector) After the Joy-pad (left) and Joy-pad (right) are installed on both sides of the bndge, they can be used as grip-type controllers, and you will not get tired when playing V mode or desktop mode for a long time, and you can teel relaxed an nappy.
About the upgrade
when the joy-pad is in shutdown mode, open the upgrade ile on the inu.nar and then inset the 11SB data cahie that has heen ted to comouter to enter the upgrade mode. lck o he .Click on the Update Firmware on the computer- Complete
Precautions
Our products do not have NFC Tunction, the joy-pad is not equipped with an nirared camera, and iS not suitabie Tor games that require sucn runctions. The built-in motor is not an HD motor, and the vibration experience may vary in some games, Our products are compatible with Nintendo Switch and Switch Lite and can be used as a replacement for the original Joy-Con, but will not work with any accessories that go with the original Joy-Con.
Frequently Asked Questions
-
How to distinguish the left and right joy-pads ?
The Joy-pad on the left has a “” button at the top right, and the Joy-pad on the right has a “+” button at the top left -
How to connect the Joy-pad to the Switch console for the first time?
Method 1: Slide the two Joy-pads along the slide rails on both sides of the main screen from top to bottom until you hear a clicking sound
Method Two:
Step 1: Press the power button on the host to enter the console interface,
dlick the “Controllers” option
Step 2: Click on the “Change Grip/Order option
Note: The method of connecting the switch lite console for the first time is the same as the second step of connecting the switch console
How to remove the Joy-pad from the console?
Press and hold the unlock button on the back of the Joy-pad and slide it from
bottom to top to remove it.
If the Joy-pad is removed from the console, the matching information with the
console will still be retained, and it can be used directly as a wireless
controller. When the pOwer is low, it can be charged by the console installed
in the charging.
How to installremove Joy-Pad from the middle frame?
Installation method: Remove the Jay-Con from the switch and slide it in from top to bottom along the left and right side of the frame until you hear the “elick” sound.
Removal method: Press and hold the unlock button on the back of the Joy-Con and slide out the Joy-Con from the bottom to the top.
FCC warning
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation, If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.