SOUNDTUBE SM1001 Passive Subwoofer Installation Guide
- June 3, 2024
- SOUNDTUBE
Table of Contents
SOUNDTUBE SM1001 Passive Subwoofer
OVERVIEW
The SM1001 ships without mounting accessories.
Optional accessories include:
- Surface Mount Bracket (AC-SM1001p-S)
- Corner Mount Bracket (AC-SM1001p-C)
Mounting brackets include
mounting instructions.
Box contents: SM1001
1 Subwoofer
4 Removable feet
1 Forged eyebolt
1 Seismic cable
3 Zip ties
Warning
SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.
Installation
- Unpack subwoofer.
- Place in desired location.
- Connect signal wire to to the Euroblock connector on the back of the subwoofer
- For a safety cable attachment, screw the forged eye bolt into the 1/4-20 inserts on the back of the speaker. Attach included safety cable from forged eyebolt to secure mounting point on structure. Installer to supply structural fastener
For wiring instructions, consult SM1001p installation instructions. Alternate optional accessory is a surface mount bracket (AC-SM1001p-S). This bracket is also compatible with the SM1001 Passive Subwoofer. The installation procedure is the same.
Box contents: Corner-mount kit
1 Corner-mount bracket
2 Speaker brackets
8 Fasteners (1/2 inch wood screws)
1 Security screw
Warning
SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.
Warning
Do not spec or install speaker near support beam, ventilation duct or other structure that may interfere with speaker function or dispersion
- Unpack subwoofer and unscrew 4 feet. Remove screws from rubber plugs and replace screws to fill holes.
- Choose a secure corner and mount bracket with tabs pointing up. Corner mount bracket must be mounted at least 3 inches below ceiling, beam or other top structure. Bracket accepts up to 1/4 inch lag bolts (installer supplies fasteners). Be sure mounting tabs point up.
- Mount speaker brackets to back of speaker with tabs down. Use included 1/2 inch wood screws.
- For a safety cable attachment, screw the forged eyebolt into the 1/4-20 insert on the back of the speaker and attach included safety cable from forged eyebolt to a secure mounting point on the structure. Installer to supply fasteners to structure.
- Run wires through hole in top or bottom of bracket. Connect wires and set gain and filters as described in the SM1001p installation instructions.
- Slide speaker onto pre-mounted bracket.
- Install security screw.
- Done!
For wiring instructions, consult SM1001p installation instructions. Alternate optional accessory is a corner mount bracket (AC-SM1001p-C). This bracket is also compatible with the SM1001 Passive Subwoofer. The installation procedure is the same.
Box contents: Surface-mount kit
1 Surface-mount bracket
2 Speaker brackets
8 Fasteners (1/2″ wood screws)
1 Security screw
Warning
SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.
-
Unpack subwoofer and unscrew 4 feet. Remove screws from rubber plugs and replace screws to fill holes.
-
Choose a secure mounting surface with sufficient strength to reliably hold the speaker. Surface-mount bracket must be mounted at least 3 inches below ceiling, beam or other top structure. Bracket accepts 1/4 inch lag bolts (installer to supply fasteners). Be sure mounting tabs point up.
-
a. Outward aiming: Mount speaker brackets to back of speaker with tabs down.Use included 1/2 inch wood screws.
3b. Downward aiming: Mount speaker brackets to top of speaker with tabs facing front of speaker. Use included 1/2 inch wood screws. -
For a safety cable attachment, screw the forged eye bolt into the 1/4-20 inserts on the back of the speaker. Attach included safety cable from forged eyebolt to secure mounting point on structure. Installer to supply fastener to structure.
-
Connect wires and set gain and filters as described in the SM1001p installation instructions.
-
Slide speaker onto pre-mounted bracket
-
Install security screw.
-
Done!
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>